• 한국분말재료학회지
• /
• 제26권3호
• /
• pp.208-213
• /
• 2019

In this study, lanthanum oxide ($La_2O_3$) dispersed molybdenum ($Mo-La_2O_3$) alloys are fabricated using lanthanum nitrate solution and nanosized Mo particles produced by hydrogen reduction of molybdenum oxide. The effect of $La_2O_3$ dispersion in a Mo matrix on the fracture toughness at room temperature is demonstrated through the formation behavior of $La_2O_3$ from the precursor and three-point bending test using a single-edge notched bend specimen. The relative density of the $Mo-0.3La_2O_3$ specimen sintered by pressureless sintering is approximately 99%, and $La_2O_3$ with a size of hundreds of nanometers is uniformly distributed in the Mo matrix. It is also confirmed that the fracture toughness is $19.46MPa{\cdot}m^{1/2}$, an improvement of approximately 40% over the fracture toughness of $13.50MPa{\cdot}m^{1/2}$ on a pure-Mo specimen without $La_2O_3$, and this difference in the fracture toughness occurs because of the changes in fracture mode of the Mo matrix caused by the dispersion of $La_2O_3$.

• 한국결정성장학회지
• /
• 제9권1호
• /
• pp.23-28
• /
• 1999

Au 미립자가 분산된 $TiO_{2}$ 박막을 졸겔담금법과 열처리공정으로 실리카 유리기판위에 제조하였다. $TiO_{2}$ 박막제조는 titanium tetraisopropoxide-EtOH-HCl-$H_{2}O$-hydrogen tetrachloroaurat (III) tetrahydrate계를 이용하였다. 고농도로 Au 화합물을 함유하면서 투명한 코팅용액을 형성하는 조건을 검토하였다. Au 금속미립자의 크기를 조절하기 위하여 광환원공정을 채택하였다. UV 조사에 따른 Au 입자의 변화와 $TiO_{2}$ 매트릭스의 상전이과정을 XRD, SEM, TEM and UV-visible spectrophotometer로 관찰하였다. 분산제로서 CPCl (Cetylpyridinium chloride monohydrate)의 효과를 평가하였다.

• 한국수소및신에너지학회논문집
• /
• 제2권1호
• /
• pp.57-67
• /
• 1990

This study is proposed to investigate the effect of electrode preparation method for Alkaline Fuel Cell using NaOH as an electrolyte on the Fuel Cell performance. The materials used for the preparation of electrode are Pt and Ag on Vulcan XC-72. Surface area of Vulcan XC-72 have different values according to the pretreatment conditions and the dispersion of Pt is dependent on the impregnation Particle size of Pt impregnated on unpretreated carbon was observed to be $20{\sim}40{\AA}$ and that on pretreated carbon in $N_2$ stream at $950^{\circ}C$ was found to be finely dispersed less then $15{\AA}$. The electrode performance was affected by the particle size of metals and operating temperature. It was revealed from this study that the optimum particle size about $30{\AA}$ and optimum temperature range is between $90{\sim}100^{\circ}C$.

• 한국수소및신에너지학회논문집
• /
• 제28권1호
• /
• pp.77-84
• /
• 2017

In this study, Poly-urethane acrylate (PUA) was synthesized by the reaction between Polycaprolactonetriol (PCLT) and Isophorone dissocyanate (IPDI) and hybridized with inorganic materials. Tetraethylortho silicate (TEOS) and nano clay (Closite 20A) were used as inorganic particles. For the hybridization of TEOS with PUA, sol-gel method is used, in which TEOS is made into spherical particle in the firsthand. In the case of Nano clay, hybridization is carried out through the dispersion as Nano clay has a layered structure. The solution of PUA hybrid was made into a film after UV curing and its thermo and electrical properties were measured. The experimental analysis and result demonstrate that the PUA hybrid shows an improved thermal properties and lower dielectric constant than that of the non-hybrid PUA. The trend of improved properties was different depending on structure of inorganic materials.

• 한국수소및신에너지학회논문집
• /
• 제22권2호
• /
• pp.240-248
• /
• 2011

All-vanadium redox flow battery (VRFB) has been studied actively as one of the most promising electrochemical energy storage systems for a wide range of applications such as electric vehicles, photovoltaic arrays, and excess power generated by electric power plants at night time. Among consisting elements of the VRFB, the ion exchange membrane and the electrode play important roles. In this study, carbon PVC coposite sheets for the VRFB have been developed and electrochemical characteristics investigated. Current collector for VRFB, carbon PVC composite sheets (CPCS), were prepared with G-1028 as a conducting particle, PVC as a polymer, Dibutyl phthalate (DBP) as a plasticizer and fumed Silica (FS) as a dispersion agent. CPCS has been shown to have the characteristics as an excellent current collector for VRFB and electrochemical properties of specific resistivity 0.31 ${\Omega}cm$, which were composed of G-1028 80 wt%, PVC 10 wt%, DBP 5 wt% and FS 5 wt%.

• 한국수소및신에너지학회논문집
• /
• 제24권5호
• /
• pp.451-460
• /
• 2013

In a direct coal fuel cell (DCFC) system, it is essential to identify volume fraction of coal suspended in electrolyte melt in order to control its dispersion and fluidity. This requirement is compelling especially at anode channel where hot slurry is likely to flow at low velocity. In this study, light scattering techniques were employed to measure the volume fraction for a pulverized coal suspension with relatively high absorption coefficient. The particle size, scattering angle, and volume fraction were varied to evaluate their effects on the scattering behavior as well as scattering regime. The larger coal size and smaller forward scattering angle could provide a shift to more favorable scattering regime, i.e., independent scattering, where interferences of light scattering from one particle with others are suppressed.

• 한국수소및신에너지학회논문집
• /
• 제30권6호
• /
• pp.578-584
• /
• 2019

The occurrence of white plume in the cooling tower is phenomenon that the steam in the air through the cooling tower fan is condensed again by the cold ambient air to become saturated moist air. Accordingly, this can cause many problems like spoiling landscape around the cooling tower, odor of ambient air, falling accident by frozenness in the winter, and traffic accident, etc. This study was to install the heat exchanger in the inside of the cooling tower in order to prevent the white plume phenomenon in the cooling tower without affecting the performance of cooling tower. In addition, this study was to discharge the part of cooling water into the atmosphere through the recirculation of heat exchanger after creating dry air by heating the saturated moist air to the dew point temperature. At that time, this study was to conduct the experimental study in order to secure the optimal design data to prevent the white plume in the cooling tower because it checked the dry·moist temperature and relative humidity in the inside·outside of cooling tower on the moist air, and evaluated the performance of the heat exchanger.

• 한국환경과학회지
• /
• 제30권6호
• /
• pp.501-505
• /
• 2021

V₂O₅-TiO₂ catalysts were prepared by various methods. V₂O₅-TiO₂ were prepared by sol-gel method with different drying conditions (aerogel and xerogel), and V₂O₅ supported on TiO₂ obtained by sol-gel method with precipitation-deposition method and impregnation method. The performance of the V₂O₅-TiO₂ catalysts was investigated for the selective oxidation of hydrogen sulfide in the stream containing both ammonia and excess water. All the catalysts showed good dispersion of vanadium and they had high H₂S conversion with no or little production of sulfur dioxide. The V₂O₅-TiO₂ aerogel catalyst prepared by sol-gel method with drying under super critical condition had the highest surface area which led to better catalytic activity compared to those by other synthesis methods.

• 한국수소및신에너지학회논문집
• /
• 제32권1호
• /
• pp.86-91
• /
• 2021

In order to save the energy in vehicles using renewable energy, it is necessary to reduce the weight of parts with polymer matrix composites. Carbon nanotube (CNT) is the nano-scale reinforcement used to increase the interlaminar strength of fiber reinforced composites or enhance the fracture toughness of polymer. However, since the degree of improvement in mechanical properties varies according to the various experimental conditions such as shape of reinforcement, types of matrix and dispersion of reinforcement, research to find the optimal conditions is essentially needed. In this study, CNT/epoxy composites with different CNT concentration were fabricated under the same conditions, and the optimal CNT content (2 wt%) was found through Mode 1 fracture toughness test. Furthermore, through optical microscopy, it was confirmed that the fracture toughness was rather decreased due to the CNT aggregation when the CNT content exceeded 2 wt%.

• Korean Chemical Engineering Research
• /
• 제57권3호
• /
• pp.413-419
• /
• 2019

최근 화석연료기반에서 친환경 수소 기반의 청정에너지원으로 전환되는 세계적 흐름에 따라, 수소연료전지의 고성능 저가격 핵심 소재 기술 개발에 많은 관심이 이루어지고 있다. 그 가운데 연료전지의 전해질로 사용되는 강화복합막의 기술 도입은 과불소계 술폰산 이오노머(Perfluorosulfonic acid, PFSA) 양의 감소 및 막 두께 감소를 통한 가격 저감 및 셀 저항 감소, 치수 안정성 개선 그리고 계면 안정성에 대한 확보가 가능하여 최종적으로 연료전지 성능 향상과 가격절감이 동시에 가능하다. 본 연구에서는 연료전지용 불소계 전해질 강화복합막 코팅 공정에서 이오노머 분산용매에 따라 막 형성 및 물성 변화와 연료전지 성능에 미치는 영향에 대해 연구하였다.