• 대한조선학회논문집
• /
• 제29권2호
• /
• pp.66-72
• /
• 1992

유한수심에 대한 Michell적분의 계산을 위해 선각함수를 종방향 및 수직방향에 대해 Legendre다항식으로 전개하여 조파저항계수를 형상계수와 유체동력학적계수의 곱에 대한 4중급수로 구할 수 있는 식을 얻었다. 여기서 형상계수는 선각의 기하학적 형상만의 함수이고, 유체동력학적계수는 수심에 근거한 Fn와 수심과 홀수의 배의 길이에 대한 비들만의 함수이다. Wigley의 포물선형 선각과 Series 60의 $C_B$ 0.6에 대한 계산을 수행하고 그 결과를 기존의 실험결과(무한수심) 및 다른 이론결과(유한수심)와 비교하였다.

• 한국군사과학기술학회지
• /
• 제21권1호
• /
• pp.10-16
• /
• 2018

The Republic of Korea Marine Corps is planning to develop a new amphibious assault vehicle which is able to operate with higher water speed than current KAAV. In order to achieve a higher water speed for hydrodynamically bulff-body vehicles, it is essential to develop drag reduction strategies. In this paper, resistance characteristics including trim angles of amphibious assault vehicles with several appendage designs are investigated using a commercial CFD code, STAR-CCM+. The computed results are compared with experimental data conducted at the towing tank with 1:4.5 scaled model and show good correlation. Comparing with the results of bare hull, 3.4 % of hydrodynamic drag and 52 % of trim angle are reduced by the application of double angled bow flap and a hydrofoil attached at the transom.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제4권3호
• /
• pp.322-334
• /
• 2012

This paper shows the numerical and experimental results about the hydrodynamic characteristics of X-Twisted rudders having continuous twist of the leading edge along the span. All the results were compared with those of the semi-balanced rudder. Calculation through the Reynolds-Averaged Navier-Stokes Equation (RANSE) code with propeller sliding meshes shows large inflow angle and fast inflow velocity in the vicinity of ${\pm}0.7$ R from the shaft center, so it may cause cavitation. Also, X-Twisted rudder has relatively small inflow angles along the rudder span compared with semi-balanced rudder. For the performance validation, rudders for two large container carriers were designed and tested. Cavitation tests at the medium sized cavitation tunnel with respect to the rudder types and twisted angles showed the effectiveness of twist on cavitation and the tendency according to the twist. And the resistance, self-propulsion and manoeuvring tests were also carried out at the towing tank. As a result, in the case of X-Twisted rudder, ship speed was improved with good manoeuvring performance. Especially, it was found out that manoeuvring performance between port and starboard was well balanced compared with semi-balanced rudders.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제12권1호
• /
• pp.810-818
• /
• 2020

A moored floating structure may exhibit resonant motion responses to low-frequency excitations. Similar to the resonant responses of many vibration systems, the motion amplitude of a moored floating structure is significantly affected by the damping of the entire system. In such cases, the damping contributed by the mooring lines sometimes accounts for as much as 80% of the total damping. While the damping induced by catenary mooring lines is well-investigated, few studies have been conducted on the damping induced by taut mooring lines, especially one partly embedded in soil. The present study develops a simple but accurate model for estimating the damping contributed by mooring lines. A typical type of taut mooring line was used as the reference and the hydrodynamic drag force and soil resistance were taken into consideration. The proposed model was validated by comparing its predictions with those of a previously developed model and experimental measurements obtained by a physical model. Case studies and sensitivity studies were also conducted using the validated model. The damping induced by the soil resistance was found to be considerably smaller than the hydrodynamic damping. The superposition of the wave frequency motion on the low-frequency motion was also observed to significantly amplify the damping induced by the mooring lines.

• 수산해양기술연구
• /
• 제23권4호
• /
• pp.157-162
• /
• 1987

장어통발의 P.P깔때기 살과 대나무 깔때기 살의 탄성을 측정하고 측면 구멍을 막은 통발과 원형의 유수저항, 침강시간 및 미끼의 냄새확산 등을 관찰한 다음 해상어획 시험을 행한 결과는 다음과 같다. 1. P.P 깔때기 살의 탄성은 대나무 살보다 훨씬 작고, 하중이 증가할수록 탄성회복도는 감소하였다. 2. 플라스틱 장어통발의 유수저항 R(kg)는 유속 V(m/sec)에 따라 다음 관계식으로 나타낼 수 있다. R=0.36V 상(2.01) 3. 장어통발의 침강시간은 측면 구멍을 막은 경우 수면상에서의 완전 침수까지 1~2초 정도 원형보다 지연되나 그 후의 침강속도는 거의 차이가 없었다. 4. 통발 내의 미끼 수용액은 측면 구멍을 많이 막을수록 원형보다 입구쪽으로 집중되어 확산되었다. 5. 측면 구멍을 일부 막은 통발과 원형을 가지고 어획시험을 한 결과 통발당 평균 어획미수나 평균어획량의 어획성능에 있어서 뻘로 된 어장에서는 차이가 없는 것 같다.

• 수산해양기술연구
• /
• 제44권1호
• /
• pp.68-74
• /
• 2008

This study is concerned with the development of the basic planing hull form of small fishing boat in 25 knots high speed. A series of model test to determine the optimum performance hull form of actual fishing boat with 10 gross tonnage was carried out for 5 models made available planing hull form in the circulation water channel. Model test was performed with the resistance test to study the hydrodynamic characteristics of model ships and the sinkage and trim measurement to investigate the stability of model ships and also the wave pattern observation to analyze the effectiveness of model ships. As the result, the planing hull form of P-4 with deep V type bow can be derived as the best hull form with good performance especially in ship's resistance efficiency showing less residual resistance and sinkage and trim and the spray effect, etc..

• 수산해양기술연구
• /
• 제52권2호
• /
• pp.79-87
• /
• 2016

Mobile fish-cage was developed assuming a cage net with an enclosed area, which and estimated the hydrodynamic characteristics of the cage through the model experiment. Flux-shielding plates, installed in the bow were compared with the resistance test carried out by making a hole, bilge keel and stud, and basic block flow rate consisting of the results to a flat surface plate. The experimental results confirmed the improved resistance performance effect of 3~6% in the bilge keel and the stud form. To assess the stability of the fish-cage, evaluation of the stability in accordance with the stability criteria for determining the floating docks had confirmed that it satisfied the static stability performance under operating conditions at sea.

• 대한조선학회논문집
• /
• 제50권2호
• /
• pp.88-94
• /
• 2013

The primary objective of the current work is to obviously analyze regarding effects of trim conditions of a ship on resistance performance using model test and CFD. Model tests at a towing tank are conducted to investigate resistance for trim conditions at the given same displacement. Measured resistance shows small but distinct differences according to trim conditions. However, these differences are difficult to be clarified by measured physical quantities and wave pattern analysis from model tests. CFD is employed for the assessment of resistance performance according to trim conditions. The flow computation is conducted considering free surface and dynamic trim using a commercial CFD code (STAR-CCM+). The initiative of the present work is to systematically demonstrate pressure resistance acting on each region of divided finite zones of ship surface along the length and draught direction of surface when pressure distribution on the ship is interpreted. Also, a standard to assess the pressure resistance applied on the divided regions of a ship is established.

• Journal of Ship and Ocean Technology
• /
• 제10권2호
• /
• pp.1-10
• /
• 2006

Numerical analysis of viscous flow around twin-skeg hull forms was conducted according to the variations of distance between skegs and vertical skeg inclinations by using a hydrodynamic analysis system, WAVIS. Six twin-skeg hull forms were derived by combining three distances between skegs (16m, 20m, 24m) and four vertical skeg angles ($0^{\circ},\;10^{\circ},\;15^{\circ},\;20^{\circ}$). It is found that the better resistance performance can be obtained with larger vertical skeg angle and smaller skeg distance for the present test cases. It also can be seen that the same trend is true for the nominal wake distributions in the propeller plane. Those tendencies were confirmed by the experimental results of MOERI. It is shown that numerical analysis can be a useful and practical tool for the evaluation and improvement of hydrodynamic performances for the complex stern hull forms with twin skegs.

• 수산해양기술연구
• /
• 제29권3호
• /
• pp.200-213
• /
• 1993

A model experiment on a midwater rope trawl net which is used in the North Pacific to catch alaska pollack is carried out in the circulating tank to examine the basic efficiency of the net. The prototype is the net used by M/S Hanil(1, 179GT, 2, 700PS), a Korean trawler. The model net was made according to the Tauti's Similarity Law of Fishing Gear in 1/100 scale by considering the condition of the tank. To measure the basic efficiency of the standard model net, the vertical opening and width between some points marked on the net were measured, and the hydrodynamic resistance were determined. Then the constructive conditions of the net were varied as follows and the factors were measured again to compare the efficiency of those nets with that of the standard net(A-1 type) front weight multiplied 1.5 times: A-2 type. buoyancy and depressing force multiplied 1.7 times: A-3 type. front weight multiplied 1.5 times on A-3 type: A-4 type. depressors rigged at ground rope: B type. cod-end stuffed with cashmylon wad: C type. The results obtained can be summarized as follows: 1. The vertical opening at the center of head rope was steeply decreased with the flow velocity increasing and the vertical opening H(m) can be expressed in H=1.2v super(-1.2)(v : flow velocity in m/sec). The width of the net varied a little when the flow velocity was over 0.4m/sec, and the width of net mouth showed about 37% of the distance between the fore tips of net pendant. The shape of net mouth was almost a circle at 0.2m/sec and then steeply flatted elliptically with the flow velocity increasing and the area of mouth S(m super(2)) can be expressed in S=(1.65-2.3v)$\times$10 super(-2). The hydrodynamic resistance of the net increased almost linearly with the flow velocity increasing and the resistance R(kg) can be expressed in R=3.2$\times$d/l$\times$abv. where d/l denotes the mean of d(diameter of netting twine) and l(length of a leg in a mesh) from wing tip to the end of bag-net except cod-end on the side pannel, and a denotes the strectched circumference of the net at the fore end of a meshed part and b the stretched length of the whole net from wing tip to the end of cod-end. 2. In the condition-varied nets, the vertical opening of head rope showed some increase in every type net except the C type, and the increase showed the greatest in the B type by 30~54%, whereas it showed decrease in the C type by 5~10%. Variation of the area of net mouth showed almost the same tendency as the vertical opening and the increase showed the greatest in the B type by 20%, whereas it showed decrease in the C type by 12%. Hydrodynamic resistance showed some increase in every type compared with the standard net, and the rate of increase indicated 5~10% in the A-2, A-3 and A-4 type, 22% in the B type and 3% in the C type.