• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.2
• /
• pp.271-271
• /
• 2000

Although inverter-driven hydraulic elevators(HEL's) have advantages over traditional valve-controlled HEL's energy efficiency and performance they need robustness in performance and stability to accomodate nonlinearities big parametric variations and resonances in mechanical-hydraulic inner system. In this paper a robust controller based on DGKF/μ mixed approach is applied to a HEL system with carring capacity of 24 persons for Incheon International Airport. The results of a test tower(T/T) has shown good ro-bustness in performance and stability of the proposed controller thereby proving a feasibility of this robust controller-based approach for other HEL problems.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.7 no.1
• /
• pp.11-19
• /
• 2010

A gas-assisted hydraulic breaker uses both hydraulic and pneumatic energies and the appropriate balance between them mostly effects its performance. Mathematical modeling of the breaker is established and verified by experiment. Through sensitivity analysis using AMESim, the key design parameters are selected, which mostly affect the performance of the breaker. Taguchi method is used to optimize the key design parameters to maximize the output power for long and short strokes through simulation. As the result, the output power as well as the impact energy are increased significantly compared with the existing design. The pressure pulsation in the supply line is reduced to a tolerable level and the dynamic characteristics of the piston displacement is also improved by the optimization.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.2
• /
• pp.291-295
• /
• 2006

Recently, greenhouse effect by $CO_2$ gas emitted by use of fossil fuel causes earth environmental problem. As a countermeasure of the global warming. micro hydropower under 100kW becomes the focus of attention for its clean and renewable energy sources. Newly developed micro positive displacement hydraulic turbine shows high efficiency and good applicability for the micro hydropoewer. The purpose of this study is to clarify the influence of leakage loss and effective head on the performance of the positive displacement hydraulic turbine for the further improvement of the turbine performance. The results show that the turbine. with a smaller side clearance. has much higher efficiency than that with bigger side clearance and it can sustain the high efficiency under the wider range of operation conditions. The turbine torque is proportional to the effective head and independent of the flow rate. The leakage is also dependent on the effective head but nearly independent of the flow rate.

• International Journal of Control, Automation, and Systems
• /
• v.1 no.4
• /
• pp.484-494
• /
• 2003

In this paper, we describe a hydraulic system design and vehicle dynamic modeling for development of tire roller traction, an essential aspect in the system analysis of tire rollers. Generally, tire rollers are one of the most useful types of machines employed in road construction, technically applied to many construction fields. We also conceptualize a new hydraulic and driving system as well as define the motion equations for dynamic and hydraulic analysis. First, we design the hydraulic circuit of the steering control and driving machine system, which can be employed to advance the performance of the lateral control, creating a prototype of construction equipment. Second, we formulate the hydraulic steering system model and hydraulic driving system model through tire roller system development technology. Finally, we validate the acquired performance results in actual tire roller equipment using the data acquisition system. These results may perhaps facilitate the establishment of priorities and design strategies for incremental introduction of tire roller technology into the vehicle and construction field.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.4
• /
• pp.189-196
• /
• 2000

In this study, the hydraulic breaker system was analyzed and the analysis tool using GUI was developed. The analysis on the system with the accumulator was included. from the parametric analysis, the effects of each factor were revealed. Through the simulation with varying parameters, the method to improve the performance of the hydraulic breaker system was presented. The analysis tool will help a man without special knowledge about programming analyzse the hydraulic breaker system. The result of this study will help improve the hydraulic breaker system in sight of "Blow energy" and "Blows per minute".ws per minute".uot;.

• Tribology and Lubricants
• /
• v.19 no.2
• /
• pp.59-64
• /
• 2003

In this study, the hydraulic breaker system was analyzed and the analysis tool using GUI was developed. The analysis on the system with the accumulator was included. From the parametric analysis, the effects of each factor were revealed. Through the simulation with varying parameters, the method to improve the performance of the hydraulic breaker system was presented. The analysis tool will help a man without special knowledge about programming analyze the hydraulic breaker system. The result of this study will help improve the hydraulic breaker system in sight of Blow energy and Blows per minute.

• Journal of Power System Engineering
• /
• v.15 no.6
• /
• pp.86-94
• /
• 2011

In this paper, an electro hydraulic power steering system based on electro hydrostatic actuator (EHA) is proposed. A detailed steering model for the proposed electro hydraulic power steering system including mechanical and hydraulic subsystems is established. A conventional electro hydraulic power steering system is also modeled to evaluate the performance of the proposed power steering system such as responsiveness, assist force, command tracking and steering feel by computer simulation. From the computer simulation results, it is found that the proposed power steering system based on EHA has desirable performance.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.365-366
• /
• 2006

Hydraulic circuit breaker is the most popular type of electric power circuit breaker because of its superiority of operating performance and capacity. For the improvement of hydraulic circuit breaker's operating performance, it is very important to analyze its dynamic behavior characteristics. In this study, hydraulic circuit is modeled, analyzed and experimented. As a result, the experimental data agree well with the numerical ones, and the numerical results can be applied to the design and the improvement of hydraulic electric power circuit breaker.

• Journal of Biosystems Engineering
• /
• v.17 no.1
• /
• pp.18-26
• /
• 1992

A mechanical-hydraulic hitch control system has been adapted to most agricultural tractors. But it has various defects due to friction, inertia and hysteresis. Recently a number of electronic-hydraulic hitch control systems have been developed in several countries to improve control performance of the agricultural tractors equipped with a mechanical-hydraulic hitch control system. This study was conducted to develop a new electronic-hydraulic hitch control system using an electro-hydraulic servo valve instead of an on-off valve and to carry out computer simulation of the system. According to the result of computer simulation, the control system showed the best performance when the proportional constants were 9 and 4 for position and draft control respectively. The step and frequency responses were improved as flow rate increased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.4
• /
• pp.382-388
• /
• 2004

The hydraulic and suction performance of an inducer varies sensitively with the inducer geometry and this paper deals with solidity as the inducer geometry parameter. The typical performance characteristics of a basic inducer was investigated and tests with another three inducers of which the solidity is different from each other were performed, so the effect of solidity on the inducer performance was experimentally investigated. For a fixed flow coefficient, required NPSH of the inducer did not follow the conventional similarity rule, so this paper suggested another empirical formula. The hydraulic and suction performance was measured at four cases of the tip solidity ranged from 1.32 to 2.76. As long as the tip solidity had the value above 1.84, the hydraulic and suction performance of the inducer increased with decrease in the tip solidity. With further decrease in the tip solidity up to 1.32, however, inducer head decreased and the suction performance dropped sharply.