• Geomechanics and Engineering
• /
• v.35 no.4
• /
• pp.385-393
• /
• 2023

To analyze the consolidation with horizontal sand drains, the plane strain consolidation model under multi-ramp loading is established, and its corresponding analytical solution is derived by using the separation of variables method. The proposed solution is verified by the field measurement data and finite element results. Then, the effects of the loading mode and stress distribution on consolidation and dissipation of pore pressure are investigated. At the same time, the influence of hydraulic conductivity and thickness of sand blankets on soil consolidation are also analyzed. The results show that the loading mode has a significant effect on both the soil consolidation rate and generation-dissipation process of pore water pressure. In contrast, the influence of stress distribution on pore pressure dissipation is obvious, while its influence on soil consolidation rate is negligible. To guarantee the fully drained condition of the sand blanket, the ratio of hydraulic conductivity of the sand blanket to that of clay layer k_d/k_v should range from 1.0×10⁴ to 1.0×10⁶ with soil width varying from 100 m to 1000 m. A larger soil width correspondingly needs a greater value of kd/kv to make sure that the pore water can flow through the sand blanket smoothly with little resistance. When the soil width is relatively small (e.g., less than 100 m), the effect of thickness of the sand blanket on soil consolidation is insignificant. And its influence appears obvious gradually with the increase of the soil width.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.124-130
• /
• 2003

Many structural evaluation procedures of road and airfield pavements use the Falling Weight Deflectometer (FWD) as a critical element of non-destructive deflection testing. FWD is a trailer mounted device that provides accurate data on pavement response to dynamic wheel loads. A dynamic load is generated by dropping a mass from a variable height onto a loading plate. The magnitude of the load and the pavement deflection are measured by a load celt and geophones. And database concerning pavement damage should be enhanced to analyze loss of thickness asphalt layer caused from the plastic deformation of pavement structure, such as cracking or rutting. The prototype FWD is developed, which consists of chassis system, hydraulic loading system, data acquisition and analysis system. This system subsequently merged to from automation management system and is then validated and updated to produce a working FWD which can actually be used in the field.

• Journal of Drive and Control
• /
• v.20 no.2
• /
• pp.1-6
• /
• 2023

This study aims to develop a Korean dental chair hydraulic circuit by improving the existing equipment in order to localize foreign leading companies' products. The suggested Hydraulic circuit can be applicable to varied sectors where height and backrest angle control of chair-type equipment are required. The study followed the steps below. First, three kinds of foreign hydraulic circuits were analyzed and three kinds of Korean dental chair hydraulic circuits were suggested. Second, it was determined whether the three kinds of Korean hydraulic circuits operate normally through SimulationX, a software specialized in multi domain analysis, and the effectiveness of each circuit was examined.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.6
• /
• pp.1011-1019
• /
• 2000

The purpose of this study is to examine the basis of design condition of existing treatment processes, namely, Extended Aeration Process, Conventional Activated Process, High Rate Aeration Process and Modified Aeration Process, by clarifying the correlations of influent wastewater concentration, hydraulic retention time, food-to-microorganism ratio and sedimentation of sludge, as well as to ascertain the feasibility of design, regardless of the existing design condition. In particular, this study made a priority investigation of hydraulic retention time and sludge sedimentation, because sludge sedimentation is the main factor$^{1)}$ which determines the operating conditions of existing treatment processes. Therefore, it is generally known that in case exceeds the sphere of design presented for each treatment, sludge bulking may occur. The results of Lesperance's test$^{1)}$, which formed the basis of design, showed the sphere of loading without security of sludge sedimentation, as in Fig. 1. The reason for sludge bulking in a certain condition, as above, is due to failure in application of optimum loading corresponding to each retention time by employing a few operating condition, which proved to be consecutively workable after years of trials and failures by Lesperance, for test conditions. However, the result of this test showed that in case of proper maintenance of loading. sludge sedimentation can be ensured under 120 SVI. Therefore, this study suggested hydraulic retention time and its corresponding optimum loading, and identified the hydraulic retention time as a determinant of sludge sedimentation. And. on the basis of these findings, this study suggested the feasiblity of UHR(Ultra High Rate), a new operating process, exceeding several times the applicable loading value of High Rate Aeration Process under one hour retention time which has not yet applied to the existing treatment processes.

• 한국기계연구소 소보
• /
• s.14
• /
• pp.157-168
• /
• 1985

In cargo vessels, hatch covers are used to prevent sea water from penetrating into the cargo hold and to keep the vessels buoyant. And also they can be used as cargo loading devices as in container ships. In this paper, hatch covers are classified according to their operation method and their characteristics are briefly demonstrated. Systematic description on the scantling of the hatch cover panel and how to determine the capacity of the hydraulic power system fir folding hatch cover panels are also presented. The hydraulic power system is selected from the result of dynamic analysis of the movements of the hatch cover panels when stored on the upper deck. The hatch coaming height is determined as shortly as the hydraulic cylinders can be installed. This study deals with the hatch cover system of the medium sized multi-purpose cargo vessel, but the results of this study can be applied to large-sized cargo vessels with a slight change of the input data in the calculations. Further research on the high pressure pump, hydraulic cleating system and hydraulic piping will realize domestic production of the whole hatch cover system which have been supplied from foreign makers until now

• Proceedings of the Korean Reliability Society Conference
• /
• 2001.06a
• /
• pp.91-97
• /
• 2001

These Study are for the development of the reliability assessment test code and test equipment and test procedures of the heavy sluice gate hydraulic cylinder. Because there is no reliability test code for the heavy sluice gate hydraulic cylinder inside and outside of the country, the modified reliability test code is made reference for the related existing standards like as ISO, JIS, MIL, TUV, DIN, KS and etc. In this study, the novel method is proposed to evaluate efficiency of the heavy sluice gate hydraulic cylinder on the loading conditions and established the conditions of the acceleration life test to reduce the testing time and cycles. The testing equipments for life test, lode operating test, high and low temperature test and salt spray test have been established for 8 month, and the reliability tests are accomplished. The test results of the heavy sluice gate hydraulic cylinder which is produced and tested initially in Korea are satisfied the durability life cycle on the using conditions.

• Magazine of korean Tunnelling and Underground Space Association
• /
• v.21 no.2
• /
• pp.103-116
• /
• 2019

Permanent sprayed concrete tunnel linings waterproofed with bonded membranes have been used at a number of important traffic projects over the last decade. Research has been carried out in several teams in order to increase the understanding of the function, properties and behavior of such linings under different loading and boundary conditions. The basic layout of this lining gives fundamental different system properties compared to the traditional lining systems. The main differences pertain to the groundwater exposure and the resulting hydraulic loading, the response of the concrete and membrane materials to this loading, as well as the geomechanically induced loading of the lining structure. The current understanding of the function and properties of such lining structures is presented in the paper based on review of recent research carried out in Norway, as well as field observations and monitoring carried over a several years. The influence of the water exposure on the final condition of the concrete and membrane materials has proven to be of vital importance for proper material testing and acceptance, assessments of the mechanical contribution of the bonded membrane, as well as assessments of the longterm durability of such linings. Obtaining realistic material parameters for the concrete and membrane materials subject to the boundary conditions posed by the groundwater exposure in an undrained structure is emphasized. Finally, some recent results from currently ongoing research on such linings, particularly the hydraulic response of the rock mass and the long term behavior of the concrete and membrane materials are presented.

• Structural Engineering and Mechanics
• /
• v.12 no.2
• /
• pp.157-168
• /
• 2001

In this paper, experimental investigation into the behavior of reinforced concrete (RC) columns tested under large lateral displacement with four different types of loading arrangements is presented. Each loading arrangement has a different system for controlling the consistency of the loading condition. One of the loading arrangements used three units of link mechanism to control the parallelism of the top and bottom stub of column during testing, and the remaining employed eight hydraulic jacks for the same purpose. The loading systems condition used in this investigation were similar to the actual case in a moment-resisting frame where the tested column was displaced in a double curvature. Ten model column specimens, divided into four series were prepared. Two columns were tested monotonically until collapse, and unless failure took place at an earlier stage of loading, the remaining eight columns were tested under cyclic loading. Test results indicated that the proposed system to keep the top and bottom stubs parallel during testing performed well.

• Computers and Concrete
• /
• v.24 no.6
• /
• pp.527-539
• /
• 2019

In this paper, the fracture characteristics of concrete specimens with different notch depths under three-point flexural loads are studied by finite element and fracture mechanics methods. Firstly, the concrete beams (the size is 700×100×150 mm) with different notch depths (a=30 mm, 45 mm, 60 mm and 75 mm respectively) are tested to study the influence of notch depths on the mechanical properties of concrete. Subsequently, the concrete beams with notch depth of 60 mm are loaded at different loading rates to study the influence of loading rates on the fracture characteristics, and digital image correlation (DIC) is used to monitor the strain nephogram at different loading rates. The test results show that the flexural characteristics of the beams are influenced by notch depths, and the bearing capacity and ductility of the concrete decrease with the increase of notch depths. Moreover, the peak load of concrete beam gradually increases with the increase of loading rate. Then, the fracture energy of the beams is accurately calculated by tail-modeling method and the bilinear softening constitutive model of fracture behavior is determined by using the modified fracture energy. Finally, the bilinear softening constitutive function is embedded into the finite element (FE) model for numerical simulation. Through the comparison of the test results and finite element analysis, the bilinear softening model determined by the tail-modeling method can be used to predict the fracture behavior of concrete beams under different notch depths and loading rates.

• Agricultural and Biosystems Engineering
• /
• v.3 no.2
• /
• pp.73-78
• /
• 2002

Cabbage is one of the most important vegetable in Korea. The cabbage production was mainly based on human labor A comprehensive research fur substituting the human labor by machines has been performed until now. In general, cabbage is cultivated on hillside in Korea. Picking up the harvested cabbages in field and carrying to a vehicle fur transportation are very laborious work. Manual transportation of cabbage is likely to damage the quality and is also a cause to increase the cost of cabbage production. This study was to develop and evaluate a prototype cabbage loader fur efficient and safe transportation of cabbage. The developed loader was a semi-tracked vehicle operated by a hydraulic system, allowing the safe transportation and loading of cabbage in a steep field. The maximum loading weight of the loader was 1.0 ton. By using two sets of safety devices attached to the loader to avoid the roll-over in a steep field, the static rollover slopes were increased up to 34.0% and 37.4% fur the left and the rear direction, respectively The maximum field speed was about 6km/hr with two cabbage pallets of 750kg at a 25% inclined field. The loading capacity of the loader was about 35 pallets/hr when picking up, carrying, and unloading two cabbage pallets for one loading operation. The loading capacity was more than 8 times in comparison with the conventional human labor. The developed loader could be used fur loading and carrying the other vegetables. The study suggested a possible approach for designing the field machines operated on hillside.