• Computers and Concrete
• /
• 제22권3호
• /
• pp.291-303
• /
• 2018

As the concept of "sponge city" is proposed, the pervious concrete for permeable pavement has been widely used in pavement construction. This paper aims at investigating the dynamic behavior and energy evolution of pervious concrete under impact loading. The dynamic compression and split tests are performed on pervious concrete by using split Hopkinson pressure bar equipment. The failure criterion on the basis of incubation time concept is used to analyze the dynamic failure. It is demonstrated that the pervious concrete is of a strain rate sensitive material. Under high strain rate loading, the dynamic strength increases while the time to failure approximately decreases linearly as the strain rate increases. The predicted dynamic compressive and split tensile strengths based on the failure criterion are in accordance with the experimental results. The total damage energy is found to increase with the increasing of strain rate, which means that more energy is needed to produce irreversible damage as loading rate increases. The fractal dimensions are observed increases with the increasing of impact loading rate.

• Structural Engineering and Mechanics
• /
• 제44권6호
• /
• pp.753-762
• /
• 2012

The ratcheting characteristics of cylindrical shell under cyclic axial loading are investigated. The specimens are subjected to stress-controlled cycling with non-zero mean stress, which causes the accumulation of plastic strain or ratcheting behavior in continuous cycles. Also, cylindrical shell shows softening behavior under symmetric axial strain-controlled loading and due to the localized buckling, which occurs in the compressive stress-strain curve of the shell; it has more residual plastic strain in comparison to the tensile stress-strain hysteresis curve. The numerical analysis was carried out by ABAQUS software using hardening models. The nonlinear isotropic/kinematic hardening model accurately simulates the ratcheting behavior of shell. Although hardening models are incapable of simulating the softening behavior of the shell, this model analyzes the softening behavior well. Moreover, the model calculates the residual plastic strain close to the experimental data. Experimental tests were performed using an INSTRON 8802 servo-hydraulic machine. Simulations show good agreement between numerical and experimental results. The results reveal that the rate of plastic strain accumulation increases for the first few cycles and then reduces in the subsequent cycles. This reduction is more rapid for numerical results in comparison to experiments.

• Geomechanics and Engineering
• /
• 제14권2호
• /
• pp.203-209
• /
• 2018

Reliable estimation of compressive as well as tensile in-situ stresses is critical in the design and analysis of underground structures and openings in rocks. Kaiser effect technique, which uses acoustic emission from rock specimens under cyclic load, is well established for the estimation of in-situ compressive stresses. This paper investigates the Kaiser effect on marble specimens under cyclic uniaxial compressive as well as cyclic uniaxial tensile conditions. The tensile behavior was studied by means of Brazilian tests. Each specimen was tested by applying the load in four loading cycles having magnitudes of 40%, 60%, 80% and 100% of the peak stress. The experimental results confirm the presence of Kaiser effect in marble specimens under both compressive and tensile loading conditions. Kaiser effect was found to be more dominant in the first two loading cycles and started disappearing as the applied stress approached the peak stress, where felicity effect became dominant instead. This behavior was observed to be consistent under both compressive and tensile loading conditions and can be applied for the estimation of in-situ rock stresses as a function of peak rock stress. At a micromechanical level, Kaiser effect is evident when the pre-existing stress is smaller than the crack damage stress and ambiguous when pre-existing stress exceeds the crack damage stress. Upon reaching the crack damage stress, the cracks begin to propagate and coalesce in an unstable manner. Hence acoustic emission observations through Kaiser effect analysis can help to estimate the crack damage stresses reliably thereby improving the efficiency of design parameters.

• 농업과학연구
• /
• 제43권3호
• /
• pp.450-458
• /
• 2016

High performance small and mid-sized tractors are required for dryland and orchard operations. A power transmission system is the most important issue for the design of high performance tractors. Many operations, such as loading and lifting, use hydraulic power. In the present study, a hydraulic power transmission system for the 3-point hitch of a 50 kW narrow tractor was developed and its performance was evaluated. First, major components were designed based on target design parameters. Target operations were spraying, weeding, and transportation. Main design parameters were determined through mathematical calculation and computer simulation. The capacity of the hydraulic cylinder was calculated taking the lifting force required for the weight of the implements into consideration. Then, a prototype was fabricated. Major components were the lifting valve, hydraulic cylinder, and 3-point hitch. Finally, performance was evaluated through laboratory tests. Tests were conducted using load weights, lift arm sensor, and lift arm height from the ground. Test results showed that the lifting force was in the range of 23.5 - 29.4 kN. This force was greater than lifting forces of competing foreign tractors by 3.9 - 4.9 kN. These results satisfied the design target value of 20.6 kN, determined by survey of advanced foreign products. The prototype will be commercialized after revision based on various field tests. Improvement of reliability should be also achieved.

• Journal of Biosystems Engineering
• /
• 제27권1호
• /
• pp.11-18
• /
• 2002

One of the major obstructing factors against managing dairy farm in Korea has been a shortage of roughage supply, which resulted in excessive abuse of concentrate feed. In order to solve this problem, production of the wrap silage by the winter cereal forages raised in the fallow paddy field is strongly recommended in Korea. The main objective is to develop a tractor attached round bale wrapper which can process the silage by wrapping the round bales with thin plastic films. This is the first half of the study which is divided by two parts. In this first part, bale wrapping process was analyzed, and based on this results the followings were designed, developed and tested. 1. Bale wrapper which haying the maximum capacity of 1 ton bale with various functions such as loading, wrapping, discharging the round bales and supplying and cutting wrap films was designed. 2. An actuator and its hydraulic circuit of each process were developed and tested. 3. Also, the variations of hydraulic pressure and engine speed were investigated by operating bale wrapper developed. In this test, maximum pressure of the hydraulic circuit for the bale wrapping was 130 kg/㎠ when it raised the bale, which was quite below the relief pressure of 170 kg/㎠ of hydraulic circuit. In the engine speed test, speed drop was 20∼67 rpm, which meant that there was no over-load operation. Therefore, the experiment proved that developed hydraulic circuit and mechanism is stable in bale wrapping operation

• 한국산업정보학회논문지
• /
• 제7권3호
• /
• pp.68-73
• /
• 2002

본 연구는 대중교통 수단인 버스를 이용하는 교통약자인 휠체어 장애인의 접근을 돕는 휠체어리프트 개발을 위하여 안전을 고려한 유압시스템과 제어장치를 제작하기 위한 설계기술에 대하여 논하고자 한다. 현대는 고령화시대에 진입하면서 노약자와 장애인의 이동권과 접근권이 문제로 대두되고 있다. 본 연구에서는 기존 전동휠체어장애인과 보호자를 버스에 탑승 할 수 있는 접근성을 향상하는데 중요한 역할을 하는 리프트를 제작하는 과정에서 발생되는 안정성과 편리성을 중심으로 리프트를 선계 제작하고자 한다. 이 선계기술은 노약자 및 장애인의 이동권과 접근권을 향상시킬 수 있는 전동휠체어리프트의 대량생산체제를 확보하기 위한 중요한 기초자료가 됨으로써 제품의 안전도와 정밀도 품질보증 확보에 큰 기여를 하게 된다.

• 대한기계학회논문집A
• /
• 제26권8호
• /
• pp.1552-1564
• /
• 2002

Meter-in, meter-out and bleed-off circuits are widely utilized in order to adjust the speed of a hydraulic actuator by using a flow control valve and in order to regulate the pressure of a hydraulic volume by using a simple on-off valve. In these circuits, a relief valve serves either to maintain constant system pressure or to protect the system from over-pressure loading. The relief valve of a bleed-off circuit is the second case frequently undergoing on-off action during operation. It makes the analysis of the pressure control characteristics of the circuit highly difficult. In this paper, steady-state flow rate, pressure, heat loss and efficiency of the three circuits are reexamined and basic experiments far obtaining the characteristics of a pump and relief valve are conducted. Finally, simple empirical first-order dynamic models of decreasing and increasing pressure were separately proposed and verified by comparison with experiment. As the result, the basis for the theoretical analysis of the pressure control characteristics of a bleed-off circuit using a simple on-off valve is established.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2004년도 Proceedings of ISRS 2004
• /
• pp.61-63
• /
• 2004

The procurement of a mobile microwave scatterometer platform involved the consideration to ensure a mobile platform and equipment selected full-filled technical requirement and safety standard in Malaysia. Designing, and modification works involved engineering methodology in determining and selecting a suitable hydraulic telescopic boom that suit a selected mobile platform available locally. The mobile platform is a delivery system for microwave remote sensing microwave scatterometer and other accessories to any locations in Malaysia. Total loading to be carried by the mobile platform is 4500 kg and its overall weight must be 16,000 kg as recommended by hydraulic telescopic boom manufacturers. The telescopic boom will elevate microwave scatterometer system including the antenna to a maximum height of 27 m, and can also be rotated through $3600^{\circ}$. A mechanism is incorporated in the system to enable tracking or monitoring angular movement of the hydraulic telescopic boom when positioned towards predetermined target.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.537-543
• /
• 2003

This paper presents the improved procedure to assess static and dynamic strength of crawler type excavators. A fully integrated model including front attachment and chassis was prepared for structural analysis. In this paper, two types of loading input methods were investigated and the method imposing digging force directly on bucket tooth was more convenient than imposing cylinder reaction force on cylinder pin even if the two methods showed no discrepancy in analysis results. Static strength analysis was carried out for eight analysis scenarios based on two extreme digging positions, maximum digging reach position and maximum digging force positions. The results from static strength analysis were compared with measured stresses, cylinder pressures and digging forces and showed a good quantitative agreement with measured data. Dynamic strength analysis was carried out for simple reciprocation of boom cylinders. It was recognized that the effect of compressive stiffness of hydraulic oil was very important for dynamic structural behavior. The results from dynamic strength analysis including hydraulic oil stiffness were also compared with measured acceleration data and showed a qualitative agreement with measured data.

• 한국산업정보학회:학술대회논문집
• /
• 한국산업정보학회 2002년도 춘계학술대회 논문집
• /
• pp.1-6
• /
• 2002

본 연구는 대중교통 수단인 버스를 이용하는 교통약자인 휠체어 장애인의 접근을 돕는 휠체어리프트 개발을 위하여 안전을 고려한 유압시스템과 제어장치를 제작하기 위한 설계기술에 대하여 논하고자 한다. 현대는 고령화시대에 진입하면서 노약자와 장애인의 이동권과 접근권이 문제로 대두되고 있다. 본 연구에서는 기존 전동휠체어장애인과 보호자를 버스에 탑승할수 있는 접근성을 향상하는데 중요한 역할을 하는 리프트를 제작하는 과정에서 발생되는 안정성과 편리성을 중심으로 리프트를 설계 제작하고자 한다. 이 설계기술은 노약자 및 장애인의 이동권과 접근권을 향상시킬 수 있는 전동휠체어리프트의 대량생산체제를 확보하기 위한 중요한 기초자료가 됨으로써 동 제품의 안전도와 정밀도 품질보증 확보에 큰 기여를 하게된다.