• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.4
• /
• pp.320-326
• /
• 2019

Recently, the application of atmospheric plasma technology in air filtration is increasing. Sterilization by an atmospheric plasma device is very effective. However, ozone gas, which is generated during atmospheric plasma formation, poses a hazard to human health. To reduce the ozone gas during plasma discharge, we fabricated a one-plate hybrid plasma discharge device with a heating element, which can decompose ozone gas effectively by a simple heating action. In this study, we evaluated the plasma discharge characteristics and ozone concentrations with various Ar flow rates and temperatures. With increasing Ar gas flow rate, the ozone concentration and spectrum intensity increased till an Ar gas flow rate of 60 sccm, and decreased thereafter. When discharged in high temperature, the ozone concentration and spectrum intensity decreased. Further, to evaluate the state of the treated surface under various plasma discharge and heating conditions, we measured the variation in the contact angles on the surface. Regardless of the temperature, the contact angle increased with increasing discharge voltage. However, the contact angle increased when discharged at high temperature.

• Journal of Powder Materials
• /
• v.17 no.4
• /
• pp.319-325
• /
• 2010

Electrical discharge machining (EDM) is an attractive machining technique but it requires electrically conductive ceramic materials. In this study, Alumina matrix composites reinforced with CNTs were fabricated through CNT purification, mixing, compaction and spark plasma sintering (SPS) processes. $Al_2O_3$ nanocomposites with the different CNT concentrations were synthesized. The mechanical and electrical characteristics of $Al_2O_3$/CNTs composites were examined in order to apply the materials to the EDM process. In addition, micro-EDM using wire electrical discharge grinding (WEDG) was conducted under the various EDM parameters to investigate the machining characteristics of machined hole by Field Emission Scanning Electron Microscope (FE-SEM). The results show that $Al_2O_3$/CNTs 10%Vol. was more suitable than the other materials because high conductivity and large discharge energy caused violent sparks resulting in bad machining accuracy and surface quality.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.1
• /
• pp.68-73
• /
• 2024

In this study, the praseodymium-doped yttrium phosphate (YPO₄:Pr³⁺) powder, which is well known for its high luminescent efficiency, and long life in the UV range, was synthesized with various content ratios of Pr₆O₁₁ and calcination temperature. Crystal structure and luminescent properties of various phosphor powders based on different concentrations and calcination conditions were characterized by XRD (X-Ray Diffraction) and PL (photoluminescence) spectrometers. From the XRD analysis, the structure of YPO₄:Pr³⁺ which is calcinated at 1,200℃ was stable tetragonal phase and crystal size was calculated about 25 nm by Scherrer equation. PL emission of YPO₄:Pr³⁺ with a different content ratio of Pr₆O₁₁ by excitation λ_exc=250 nm shows that 0.75 mol% phosphor powder has maximum PL intensity and PL decreases with the increase of the ratio of Pr₆O₁₁ up to 1.25 mol% which is caused by changes of crystallinity of phosphor powders. With increasing dopant ratio, photo-luminescence Emission decreases due to Concentration quenching, which is commonly observed in phosphors. Currently, 0.75 mol% is considered the optimal doping concentration. A hybrid ultraviolet-emitting device incorporating YPO₄:Pr³⁺ fluorescent material with plasma discharge was fabricated to enhance UV germicidal effects while minimizing ozone generation. UV emission from the plasma discharge device was shown at about 200 nm and 350 nm which caused additional emission of the regions of 250 nm, 315 nm, and 370 nm from the YPO₄:Pr³⁺ phosphor.

• Composites Research
• /
• v.23 no.3
• /
• pp.13-18
• /
• 2010

One of the biggest challenges in the nano-field is how to effectively disperse nano-scale particles, especially CNTs, which are strongly agglomerated by intermolecular van der Waals forces. This study suggests a new method, discharge flocking, in order to disperse nano-scale particles effectively, which combines corona discharge phenomenon and a traditional electrostatic flocking process. In order to evaluate the discharge flocking process, composite specimens were fabricated by the process and RFI(resin film infusion) process, and then the mechanical and electrical properties of the specimens were measured and compared. Moreover, the evaluation of gas discharge effect on the CNTs and epoxy was performed to compare the mechanical and electrical properties of the composite specimens including the plasma treated CNTs. The experimental results showed that the electrical and mechanical properties of the specimens fabricated by the discharge flocking process were similar to those of the RFI process. In addition, plasma treated CNTs were not affected by gas discharge during the discharge flocking process.