• 한국작물학회:학술대회논문집
• /
• 한국작물학회 1998년도 춘계 학술대회지
• /
• pp.123-124
• /
• 1998

• 전기화학회지
• /
• 제10권2호
• /
• pp.104-109
• /
• 2007

연료 전지의 소형화를 위하여 흑연(graphite)를 기본으로 하는 분리판을 실리콘분리판으로 대체하였으며, 실리콘 분리판과 active area가 $4cm^2$인 MEA (membrane electrode assembly)와 결합하여 단위 전지를 제작하였다. 단위 전지에 공급되는 수소와 산소의 공급량은 고정하고 가습기의 구동 온도만을 변화시키면서 단위 전지의 성능을 확인하고 최적의 가습 조건을 결정하였다. 또한 가습 조건이 실리콘으로 제작된 연료 전지 스택에 미치는 영향을 알아보기 위하여 실리콘 분리판과 2개의 MEA로 이루어진 스택을 제작하여 가습 조건의 영향을 알아보고 실리콘 분리판으로 제작된 연료전지 스택의 문제점 및 특징을 알아보았다.

• 한국분무공학회지
• /
• 제23권1호
• /
• pp.30-35
• /
• 2018

The objective of this study is to predict numerically the effect of intake humidification on the injected diesel fuel spray characteristics in a compression ignition engine. In this work, Wave model and Ducowicz model were applied as the break-up model and evaporation model, respectively. The amount of water vapor for the humidification was changed from 0% to 30% of injected fuel mass. The number of applied meshes was generated from 49,000 to 110,000. At the same time, the results of this work were compared in terms of spray tip penetration, SMD and equivalence ratio distributions. It was found that the cylinder temperature and cylinder pressure were decreased with increasing water vapor mass by vaporization latent heat and specific heat, however, the difference was very small. So, the spray tip penetration was not different by water vapor mass. Also, higher equivalence ratio distributions were observed with increasing water vapor mass by the improvement of fuel atomization.

• Journal of the Korean Wood Science and Technology
• /
• 제20권3호
• /
• pp.29-37
• /
• 1992

This research was carried out to investigate the effects of cyclic humidification on the dimensional stability of particleboard manufactured according the three specific gravity levels and com-ply fabricated with a core of particleboard and veneer or plywood as the face and back materials. Both the particleboard and com-ply were subjected to four cycles of 50-90-50% relative humidity. The results are summarized as follows: Particleboard and com-ply followed a clear pattern of increasing dimensions and weight on the adsorption cycle and decreasing dimensions and weight on the humidification cycle. After the fourth cycle, the dimensions and weight of both particleboard and com-ply were greater than those originally measured. The greater part of increase in occurred during the first humidification cycle. The specific gravity of particleboard has a significant effect thickness and volume change. The dimensional stability of com-ply was better than that of particleboard. In addition, the dimensional stability of com-ply bonded with plywood was better than that of com-ply bonded with veneer.

• Child Health Nursing Research
• /
• 제17권2호
• /
• pp.145-152
• /
• 2011

Purpose: To evaluate the efficacy of Optimal humidification during Nasal Continuous Positive Airway Pressure (nCPAP) for Extremely Low Birth Weight Infant (ELBWI). Methods: The study design was a pre-test-post-test nonequivalent nonsynchronized quasi-experimental design. The participants were 218 ELBWI on nCPAP (experimental group: 102 and control group: 116). Data collection was conducted from January 2005 to April 2010. In order to measure and analyze the nCPAP duration, reintubation and nasal condition, Chi-square test and t-test were used. Results: Hypothesis 1, that the duration with nCPAP in the experimental group is longer than that of the control group and hypothesis 2-3, that the rate of reintubation and nasal problems in the experimental group are lower than the control group, were all supported as there were statistically significant differences between two groups. Conclusion: The findings suggest that the Optimal humidification in this study is an efficient intervention because it helps increase the last time of nCPAP with ELBWI and minimize complications. It is expected that Optimal humidification is beneficial and helpful in preventing and caring for respiratory problems in these infants.

• 한국산학기술학회논문지
• /
• 제20권2호
• /
• pp.732-740
• /
• 2019

가습 소자를 이용한 증발식 가습은 건물이나 데이터 센터의 공조에 널리 사용되고 있다. 가습 소자의 성능은 가습 효율로 나타내는데 이 효율은 공기의 온습도나 물 온도에 무관하게 사용되고 있다. 본 연구에서는 데이터 센터와 건물 공조의 두 공기 조건에 대하여 셀룰로오스/PET, Glasdek의 두 소자를 사용하여 전벙 풍속과 물 온도를 변화시키며 일련의 실험을 수행하였다. 실험 결과 측정된 가습 효율은 공기 조건과 물 온도에 따라 다르게 나타났다. 심지어 건물 조건에서는 소자의 입구부에서 감습이 나타나기도 하였는데 그 이유는 공급수 온도가 입구 공기의 노점온도보다 낮았기 때문이었다. 건물 조건에서는 공급수 온도와 공기의 노점 온도 차이가 증가할수록 가습 효율은 감소하였다. 이로부터 가습 효율 모델을 적절히 세우려면 길이 방향으로 수분 전달량이 변화하는 입구 영역에 대한 해석이 중요하다고 판단된다. 셀룰로오스/PET 소자에 대하여 성능 해석을 수행한 결과 Sherwood 수는 적절히 예측하였으나 마찰 손실은 과대 예측하였다. 이는 해석시 채널 형상을 단순한 삼각형으로 가정하고 소자 표면에 형성된 액막의 영향을 무시한 때문으로 판단된다.

• 펄프종이기술
• /
• 제41권1호
• /
• pp.9-16
• /
• 2009

Cylindrical dry forming mould was developed to carry out a feasibility study of dry forming of papers. The effect of disintegration, forming, humidification and pressing on dry formed papers was examined. Dry disintegrated fibers showed the similar fiber length distribution to wet disintegrated fibers, but they showed distorsion and damaged appearance on the surface. Process parameters required to form a uniform fiber pad was investigated. A proper screening and air dispersion method was selected that gives proper formation. Humidification and pressing conditions were examined to get a good dry formed papers in dry forming. Results showed that dry forming method can be used to make a sheets with reasonable formation and properties.

• 한국작물학회지
• /
• 제43권3호
• /
• pp.157-160
• /
• 1998

To find out the effects of humidification and hardening of rice (Oryza sativa L. cv. Ilpumbyeo) seeds on the germination, both normal and artificially aged seeds with 60% germination rate were humidified at 40, 60, and 80% RHs and $25^{\circ}C$ for five weeks or hydrated for 6, 12, 18, and 24 hours at $25^{\circ}C$ from one to five cycles for hardening. Relative humidity and duration of humidification did not affect the germination rate of normal seeds, while reduced the time to get 50% germination rate ($T_{50}$) by 1.0～1.6 days compared to that of normal seeds at $25^{\circ}C$. Aged seeds humidified at 40 and 60% RHs did not affect the germination rate and $T_{50}$ regardless of relative humidity and duration of treatment, while at 80% RH, the germination rate decreased and $T_{50}$ increased significantly with the duration of humidification. Hardening of normal seeds reduced $T_{50}$ by 0.7～1.1 days without changes in the germination rate. However, the germination rate and $T_{50}$ of aged seeds soaked in water for 6, 12, and 18 hours were similar regardless of soaking/drying cycles, while hardening of artificially aged seeds with 1～4 cycles in 24 hours soaking increased the germination rate by 11-16% and reduced $T_{50}$ by 1.4～2.0 days.

• 한국산학기술학회논문지
• /
• 제19권11호
• /
• pp.326-331
• /
• 2018

최근 들어 건물이나 데이터 센터의 공조에 기화식 가습기가 널리 사용된다. 일반적으로 가습 효율은 외기 조건에 관계없이 동일하게 적용된다. 하지만 이 부분에 대해서는 확인이 필요하다. 본 연구에서는 일반 건물과 데이터 센터의 설계 온습도 조건에서 일련의 실험을 수행하고 상기 가정이 적절한지를 판단하였다. 실험에 사용된 소자는 cellulose/PET 재질로 깊이 100mm, 200 mm, 300 mm 세 종류이고 전방 풍속 1.0 m/s에서 4.5 m/s 사이에서 수행되었다. 실험 결과 가습 효율은 외기 조건에 따라 차이가 났다. 데이터 센터 ($25^{\circ}C$ DBT, $15^{\circ}C$ WBT) 조건에서 건물 공조 ($35^{\circ}C$ DBT, $21^{\circ}C$ WBT) 조건보다 크게 나타났는데 그 이유는 입구 영역에서 수분 전달 성능의 차이 때문이다. 심지어 건물 공조 조건에서는 입구 영역에서 제습이 일어났다. 또한 공급수 온도가 외기 공기의 습구온도에 근접할수록 가습 효율이 증가함을 확인하였다. 따라서 가습소자의 성능을 적절히 예측하기 위해서는 입구 영역에 대한 해석 모델이 포함되어야 한다. 한편 소자의 두께가 100 mm에서 200 mm로 되면 가습효율이 29% 증가하고 300 mm가 되면 42% 증가한다. 하지만 압력 손실도 47%, 86% 증가한다.

• 펄프종이기술
• /
• 제39권2호
• /
• pp.1-8
• /
• 2007

To examine the feasibility of dry forming technology for papermaking, a dry forming mold (DFM) was developed and evaluated. Main fanning section of DFM was a cylindrical tube, and at the top of the mold a stirring equipment was placed to disperse dry fibers. These fibers were screened using a hole type screen plate placed just under the stirring equipment and dropped freely on the fanning wire located 0.9 m below of the screen plate to form a dry fiber pad. The vertical and horizontal velocity of air flow in the forming cylinder were evaluated and analyzed to find the most effective method of air flow control in the cylinder. Humidification and pressing conditions to obtain a decent dry fanned papers were examined. Results showed dry fanned papers can be prepared with this dry forming mold. And this mold can be used to examine the effect of the papermaking process factors including pressing pressure, drying temperature, humidification on sheet quality of dry formed papers.