• Journal of the Korean housing association
• /
• v.14 no.6
• /
• pp.51-58
• /
• 2003

When apartment buildings are builed and re-builded, they tends to be taller. This tendency causes the problems for solar access and view in the neighboring area. So the impact factor of sunlight and view by apartment building in its neighboring area is examined. The results of this study are as follows： When analyzing sky view by dividing the sky vault into the differential area, the analysis of view can be efficient. The shorter the apartment building, the more the continuous solar access time. And the taller the building, the more the accumulated solar access time. As the height of building is taller and it is farther from the border of apartment building, view ratio, sky view ratio, and form ratio are increased. It implies that the slimmer the building, the more the visual environment can be improved.

• Journal of the Korean housing association
• /
• v.17 no.5
• /
• pp.107-116
• /
• 2006

This study was to figure out the design characteristics of court housing type for the purpose of searching for the possibility of applying it to the housing design in Korea. In spite of changes of housing design condition in Korea, especially steep increase in density, there have been changes only in the height of housing block, not in the housing types, layout, spatial organization and other design properties. Due to such a situation, housing in Korea has been criticised as too high, monotonous one - especially types of housing block tend to be fixed into a slab block and a point block. As one of the alternatives to respond to the criticism, this study focused on the positive aspects of the court housing type, and suggested the design direction throughout the analysis of 8 entries in the design competition of EunPyeong New Town, which attempted to overcome the negative problems - mainly the daylighting, orientation, and privacy - and tried to maximize the positive properties of this type of housing.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.3
• /
• pp.1-6
• /
• 2011

To compare the lighting environment of kitchen and bathrooms in the apartments in China and Korea, this research conducted a study of the current status, targeting 68 households in China and 79 households in Korea. The results are as follows. First, the Korean kitchen space is a little bigger than China's, but the height of the sink and table show no difference. China does not use local lighting in the kitchen. And Korea 40.2[%], China 65.6[%] is sink's KS based was below. In the case of the dining table, KS criteria satisfy both Korean and Chinese standards. 20[%] appear to be very feeble; urgent improvements are required. Secondly, regarding the size of the bathroom, Korea and China show similar sizes; the average height of the vanities and toilet is higher in Korea than in China by 2[cm]. China does not use local lighting in the bathroom. The levels of illumination were measured; lighting is higher in China's bathrooms compared to Korea's.

• Journal of the Korean housing association
• /
• v.17 no.3
• /
• pp.111-121
• /
• 2006

The objective of the study is to derive the quantitative result and method from the solar simulation on the traditional architectonic control methods and their effects for the sunshine on Ddeuljip in Northern Area of Kyongsang-Bukdo Province, Korea. The Ddeuljip(rectangular-shaped housing plan having an inner court) has distinctive form to introduce plentiful sunshine deep inside to the house in spite of disadvantageous condition resulted from the structure of traditional housing composition, that is, Ickrang(linkage block connecting buildings). From the research on the Ddeuljip, following results were derived: First, in the plan the sunshine environment was improved by placing the master bedroom on the right diagonally, or projecting it toward the Ickrang when there isn't enough space for the inner court and the Daechung(wooden floored main hall). Second in the elevation specific sunshine control methods were developed by increasing the height of the master bedroom, reducing the eaves of south elevation, or differentiating the height of ceiling structure gradually.

• Korean Membrane Journal
• /
• v.1 no.1
• /
• pp.100-105
• /
• 1999

A novel system to thicken the concentrated colloidal solution from membrane water treat-ment processes was developed. A hollow-fiber microfilter(hydrophilic polyethylene nominal pore size 0.1 ${\mu}$m total surface area 0.42 m2) was installed in an acrylic housing that has an aeration port 5 cm below the membrane and a clarifier in the bottom. The concentrate was uniformly supplied from the top of the housing. Bacuum filtration caused downward flow of concentrate and as a result thickening interface. The addition of poly-aluminum chloride (PAC) resulted in rapid increase of trans-membrane pressure (TMP) and in no improvement of the filtered water turbidity and thickening process. Two types of con-centrate and concentrate turbidity had little effect on the increase of TMP and concentrate thickening. It was observed that for the same height of membrane housing membrane surface area to housing volume (A/V) ratio had significant effect on the increase of TMP. When the housing volume was increased ten times the increasing rate of TMP was three times faster as compared to the original housing. A hydraulic model successfully simulated the formation and sedimentation of thickening interface.

• Journal of the Architectural Institute of Korea Planning & Design
• /
• v.35 no.6
• /
• pp.27-37
• /
• 2019

This study focused on the possibility of reducing the cooling load through the change of micro climate in the outdoor space during summer season. This study proposes an efficient planning model by comparing the effects of urban heat island mitigation through wind path planning, outdoor space vegetation, and exterior material change by using the basic model of the street-oriented block housing proposed in the previous research by the same author. As a result, the most effective wind path planning strategy in the street-oriented block housing was the change of the air flow through the mass height adjustment. When the tall building masses were staggered and arranged in a balanced manner, the overall wind environment could be improved. The greater the height difference between low and high masses, the better the air flow was shown. It was also important to arrange the building masses so that the inlet of the main wind was open and to allow the external space to connect to the adjacent block to create a continuous flow. The change of outdoor space vegetation and flooring, and the formation of wind paths through the opening of lower part also showed the effect of heat island reduction. In addition, the change of PMV in summer was the biggest influence of shadow by tall building mass. Attention should be paid to the fact that high-albedo exterior materials are adversely affected by multiple reflections in dense street-oriented block housing. The use of albedo of the exterior material showed that it is necessary to pay attention to apply in the high density block housing. This is attributed to the rise of the temperature due to the absorption of energy into the low-albedo flooring, where the high-albedo exterior causes multiple reflections.

• Journal of the Korean housing association
• /
• v.14 no.5
• /
• pp.105-116
• /
• 2003

The purpose of this study is to suggest the method of prevention of staircase accidents, and to make housing environment better through researching the dimension of a housing staircase for Korean. The scope and method of this thesis is to investigate the dimension limits of a staircase (slope, minimum width of tread, maximum height of riser), and to analyze the characteristics of foot condition (jutting rate, foot angle, ball joint, nosing clearance, clearance distance) using the experiment which takes a photograph of foot motion during walking stairs. The results of this thesis are as follows. The slope of a staircase in house is $32.3^{\circ}$$^{\circ}$-$42.1^{\circ}$$^{\circ}$. The riser should be less than 190 mm. The minimum size of tread is 210 mm and proper size is 270 mm.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.958-968
• /
• 1994

This paper presents a dynamic analysis of the high-speed spindle system for vertical machining center using finite techniques. The computed natural frequencies are compared with the measured frequencies obtained from experimental modal analysis. The results show that the bending and twisting deformations of the spindle housing dominate in the lowest modes owing to low dynamic stiffness of the housing structure. The design parameters in the analysis are : (a) panel thickness of the housing (b ) height of the housing, and (c) spindle-to-column distance of the housing. Through sensitivity analysis and optimizing simulation considering design constraints, an optimal design of the spindle system has been obtained.

• Journal of the Optical Society of Korea
• /
• v.19 no.5
• /
• pp.531-536
• /
• 2015

This paper presents a new graphical method for selecting a pair of optical glass and housing materials to simultaneously achromatize and athermalize a multilens system composed of many elements. To take into account the lens spacing and housing, we quantify the lens power, chromatic power, and thermal power by weighting the ratio of the paraxial ray height at each lens to them. In addition, we introduce the equivalent single lens and the expanded athermal glass map including a housing material. Even though a lens system is composed of many elements, we can simply identify a pair of glass and housing materials that satisfies the athermal and achromatic conditions. Applying this method to design a black box camera lens equipped with a 1/4-inch image sensor having a pixel width of $2{\mu}m$, the chromatic and thermal defocusings are reduced to less than the depth of focus, over the specified ranges in temperature and frequency.

• Journal of the Korean housing association
• /
• v.23 no.6
• /
• pp.11-20
• /
• 2012

This Study developed library of parts, applied with 3-dimension character which has width, length and height and a reference plane, for the system development of BIM design on housing unit modular. The current BIM software has not the concept of a reference plane or work tolerance in modular, so the development of parts library applied to unit modular has not moved forward. So, we developed, in this study, parts library applied to windows, built-in-furniture, kitchen systems and knock down bathrooms, with a reference plane and work tolerance based on single roon prototype on urban-life-housings. BIM library can utilize changed size and work tolerance of parts, and fabricating reference plane will be created automatically when an engineer puts work tolerance in the BIM library with supplement of some category related to work reference. Through this BIM library development, we consider the part module can be used for housing complex planning, and architectural designers will be able to utilize the BIM library for housing complex design.