• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.1159-1162
• /
• 2003

Recently we suffered lot of failures of polymer surge arresters made by same manufacture after one year field operation. In order to set up countermeasures we investigated the causes of failures. We extracted faulted arresters and sound ones which were installed in same pole with faulted ones for the electrical test and dissection. 44 arresters were removed from 8 branch offices. Almost all of faulted arresters hadtracking damage on the interface between inner module and housing and the surface of inner module was very rough and irregular. It was possible to occur moisture ingress into the interface between inner module and housing due to the void of the interface and non tight sealing caps. Lots of sound arresters were failed during the moisture ingress test. This result must relate with tracking damage of faulted arresters. Therefore we can say that arresters had poor interface and sealing system. But we could not found aging and defects of ZnO elements because the electrical performance except moisture ingress test of arresters showed good.

• International Journal of Concrete Structures and Materials
• /
• v.9 no.4
• /
• pp.439-451
• /
• 2015

This study analyzed the isolation effect for a 15-story reinforced concrete (RC) building with regard to changes in the beam-column stiffness ratio and the difference in the vibration period between the superstructure and an isolation layer in order to provide basic data that are needed to devise a framework for the design of isolated RC buildings. First, this analytical study proposes to design RC building frames by securing an isolation period that is at least 2.5 times longer than the natural vibration period of a superstructure and configuring a target isolation period that is 3.0 s or longer. To verify the proposed plan, shaking table tests were conducted on a scaled-down model of 15-story RC building installed with laminated rubber bearings. The experimental results indicate that the tested isolated structure, which complied with the proposed conditions, exhibited an almost constant response distribution, verifying that the behavior of the structure improved in terms of usability. The RC building's response to inter-story drift (which causes structural damage) was reduced by about one-third that of a non-isolated structure, thereby confirming that the safety of such a superstructure can be achieved through the building's improved seismic performance.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.3
• /
• pp.234-239
• /
• 2013

There are many types of speed reducer for industrial uses. However the cycloid speed reducer is widely used in manipulators based on excellent performance of low backlash, high reduction ratio and compact size. It is essential to use precision speed reducer for accuracy of position controls on robot systems and electric vehicles. The cycloid speed reducer has a eccentric rotating motion and offset to avoid some problem of assembly, so it has a disadvantage for vibration. In this paper, a multi-body dynamic model is developed for a cycloid speed reducer and the dynamic behaviors of the reducer are investigated. The cycloid speed reducer consists of cycloidal plate gears, housing gear, input shaft, output pin and shaft, and eccentric bearings. Using a CAD program, each component of cycloid reducer is modeled based on the offset and eccentric. Multi-body simulations using Recurdyn and test using a rig tester are performed. As a result, the pin reaction force and the amplitude of housing displacement are increased by the larger offset and smaller eccentric value of cycloid reducer.

• Journal of the Korean housing association
• /
• v.24 no.5
• /
• pp.69-76
• /
• 2013

The seriousness of greenhouse gas exhaustions and energy use of the building has increased, the world is making an effort with many requests and the consultation for sustainable development. For this reason, Green Building Certification Criteria has been implemented to reduce environmental load, high-performance and environmentally friendly in the United States, the United Kingdom and Germany. In response to the global trend like this, the Korean Government has induced the eco-friendly construction and sustainable development to implement the G-SEED (Green Building Certification Criteria of Korea) in 2002. However, in spite of the many authentication result, G-SEED has been pointed out that it needs for improve in the evaluation system of Apartment sector which accounts for more than 40% of the authentication. Therefore, the purpose of this study is to suggest improvements in the evaluation system. To achieve this, this study have selected for LEED, BREEAM, DGNB of comparison target, drawn improvements through comparing transition process in G-SEED.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.3
• /
• pp.273-280
• /
• 2007

In this paper, the ZnO surge arrester performance of power distribution class has been studied under different manufacturing conditions such as housing materials(polymeric, porcelain), interface sealants and one-body molding type. In the recent years, the polymeric ZnO surge arresters have been developed and put into operations based on their excellent characteristics. For polymeric surge arresters, the inner gas volume is extremely small, especially in solid insulation polymeric arresters there are not any gas volume inside arresters in the structure due to polymeric materials are filled into the internal gas volume. The sealing integrity is related to safe operation of surge arrester, the prime failure reason of porcelain housed arresters is moisture ingress. In this paper, the sealing integrity of polymeric surge arresters is investigated with moisture multi-aging test and ingress test. The evaluation techniques are used to inspect the sealing integrity of polymeric arresters, including leakage current, surface temperature, reference voltage and dissipation factor.

• Korean Institute of Interior Design Journal
• /
• v.13 no.5
• /
• pp.48-55
• /
• 2004

The remodeling of apartment that improves the improves the life level is going to be in the market because of lots of old apartment buildings. Until now, the research of remodeling is mainly restricted to the laws and financial funding, however, the needs in the trend of remodeling. This research, first, through the examples of remodeling in the country, this study draws remodeling factors that can be applied. Secondly, this study targets the study of remodeling to apartments and analyzes the type of housings made by the Korea National Housing Corporation. Thirdly the study analyzes the features that appear in housing units and draws out factors of remodeling This research's result Is arranged as follows. \circled1Need Remodeling thorough study of space expanded, grant between artificer and active performance improvement direction such as building equipment expansion along with Remodeling concept of unit repair. \circled2When apartments are newly built, systematic construction is necessary that considers future efficiency improvement from the design stage. \circled3This study, which applied the characteristic factors appearing after the 1990s to remodeling factors, show that they can be applied when remodeling the worn out wall-slab type apartments.

• Journal of the Korean Home Economics Association
• /
• v.42 no.12 s.202
• /
• pp.175-190
• /
• 2004

The purposed of this research was to suggest a basic material of Korean-typed cohousing plan for a dual-income family by examining the difference of cohousing residing environment needs. Selecting Employed and unemployed housewives as this research's subject, the following results were drawn from the analysis between the two groups. 1) The housewives takes responsibility of the household works regardless of whether or not they are employed. Also, more than half of employed housewives stated that the time of nursery facilities was shorter than their needs and that they favored a nursery facility located inside the residential area. 2) The most meaningful difference of cohousing residing environment needs was the demand for sharing household work in terms of cohousing need of the subjects. The desirable cohousing area is the suburbs of the metropolitan areas and the preferable resident organization is need to be organized by people sharing the same goal through an announcement. 3) The need of cohousing and residence intention were generally low, but the employed housewives' need was higher than the unemployed ones.

• KIEAE Journal
• /
• v.15 no.5
• /
• pp.89-94
• /
• 2015

Purpose: Various policies to reduce the energy consumption have been carried out to save Earth environment against global warming and environmental pollution in many countries. Energy consumption of buildings in Korea has reached 24% of total energy consumption, and energy consumption of apartment has been continuously increasing. Therefore, Korea government has executed building energy efficiency rating certification system to control energy consumption of buildings. Method: This study was conducted to evaluate the energy performance of apartment unit plans according to the increasement of front width of unit plans, and tried to present the basic data to design more energy conscious unit plans for apartments. For the study, three shapes of unit plans -the 2Bay, 3Bay and 4bay unit- were selected for imput models. They were simulated using ECO2 software to assess building energy efficiency rating certification in Korea. Result: According to the results, in cases that balcony windows were not installed, the primary energy consumption of the 3Bay and 4Bay units were less than 2Bay unit, respectively, 0.1% and 2,5%. The primary energy consumption of the 3Bay and 4Bay units, in cases that balcony windows were installed, was less than 2Bay unit, respectively, 1.7% and 3.2%.

• KIEAE Journal
• /
• v.7 no.1
• /
• pp.95-100
• /
• 2007

In apartment houses, said to be similar to a typical housing form, every household share the walls and floors. Many problems inevitably accompany such as an arrangement, as noise and vibration are shared among households. When investigating the percentage of apartment resident's dissatisfaction with housing environments, discontent due to noise ranks the highest. Among many different kinds of noises, noise such as floor crashing sounds show the highest indication rate in the residents' comparison of discontent. Therefore, it is the practice of insulating against noises such as floor crashing sounds that improves the apartment house environments. The factors influencing the floor impact sound insulation include floor finishing materials, shock absorbing floors (slabs included), and ceiling structures. The ceilings of the apartment houses, currently built in Korea, are set up with lower parts of slabs and paper finishing, or with double floors for protecting against floor impact sounds in order to improve the sound insulating performance. The most common the method of ceiling structure construction consists of 'wood boarded frames +Gypsum boards + ceiling papers', which is called the wood boarded frame method. This study aimed to measures and evaluates floor impact sound insulation by which the ceiling space are widened according to suppression system is added in apartment house ceiling structure.

• Land and Housing Review
• /
• v.10 no.2
• /
• pp.53-58
• /
• 2019

Particulate matter (PM) is designated as a group 1 carcinogen by the International Agency for Research on Cancer (IARC) of the World Health Organization (WHO). In South Korea, the health threat caused by PM is the most serious level internationally. Therefore, in order to solve the urban PM problem, it is important to develop the technology that can control PM efficiently. In this study, CFD(Computational Fluid Dynamics) simulation was performed for PM pre-filter (type 1-3 with different PM collecting room) to develop a high-efficiency PM collecting device. The complex flow field and the local flow phenomenon inside the PM collecting device were understood with CFD simulation by changing the shape and size of the pre-filter. The PM removal performance can be described with flow rate through the device and PM removal efficiency. The type-1 pre-filter with 5x5 size collecting room was confirmed to have the highest efficiency. Based on the analysis results, the optimal type of pre-filter could be developed and it would be applied as an element technology included in the PM collecting device.