• Journal of the Korean housing association
• /
• v.12 no.3
• /
• pp.141-148
• /
• 2001

To design mechanical ventilation for bathroom of apartment houses where air supply and exhaust are taken into consideration, mock-ups of ventilation systems, widely used in bathroom of apartment houses with an area of 100$\textrm{m}^2$, were made and installed in a laboratory. These ventilation mock-ups were available for control of air supply and exhaust, and the sizes of supply openings were 40cm${\times}$1cm, 40cm${\times}$3cm, and 40cm${\times}$5cm. They were installed at five positions, spaced 45cm at a height of 5cm from the floor. The exhaust fan was designed for its operating voltage to be set to five steps(100V, 130V, 150V, 180V and 220V) in order to control its air flow rates. When the size and position of each supply opening were changed with the wind velocity of the exhaust fan set to the step 5, the ventilation rates were measured and analyzed by the concentration decay method of tracer gas method, in order to present an efficient mechanical ventilation system. The results of the study revealed that the ventilations rates would increase in the presence of supply openings, compared to the absence of supply openings, and that the larger the size of the supply opening, the more the ventilation rates. Therefore, it was found necessary to take air supply into consideration.

• Journal of the Korean housing association
• /
• v.23 no.4
• /
• pp.41-48
• /
• 2012

The purpose of the study, approaching from the aspect of the construction technologies, is to determine the architectural techniques of traditional wood architects in existence, through which the systems and techniques that create the inherent characteristics of Korean Architecture are clarified. With understanding traditional construction system and focusing on the fact that built environment results from the consistent standards and technologies of architects, this study inquires into the systematic standard and its formation that present in the process of planning for the overall scale and shape of a building from the following (four) perspectives. The study determines the characteristics of '間(Kan)' (unit; fundamental unit that measures Korean traditional houses) and the methods of columns disposition of which the '間 (Kan)' is made up. Once the necessary spaces are decided according to the size of a building, then floor plans are drawn with the standard unit, '間(Kan)'. The '間(Kan)', as a modular unit, is not only composing the floor plans, but also functioning as an Area unit, Space unit and Structural unit. Composition of '間(Kan)' varies with disposition of columns, and therefore multiform of floor and spaces are created. In this study, the '間(Kan)', as a standard unit, is used in the form of specific size and area, and it is demonstrated how the floor plans are developed by organizing the columns in accordance with the spaces requested.

• Journal of Families and Better Life
• /
• v.20 no.6
• /
• pp.219-227
• /
• 2002

This study was conducted to examine housing preferences among single-person households and to propose guidelines for housing design choices for single people. One hundred and sixty responses to the questionnaire developed by this researcher were analyzed utilizing frequencies, percentages, and t-tests. There were significant differences between single households and non-single households in various aspects of housing preferences. Differences were found in the desired type and size of housing, needed amount of space, and the importance of space itself. Single persons wanted to live in a small apartment, about 83.45$m^2$ (25.29 pyung) size. They consider the bathroom and the master bedroom more important than the living room and kitchen. They prefer to have specifically function-oriented rooms such as shower, home office, computer room, exercise room, or leisure space. Single persons consider information-technological facilities within an apartment very important. They would like to adopt automatic and electronic technology in the house, such as optical communication network, automatic air-cleaning system, and internet TV. Housing preferences differ significantly according to socio-demographic variables such as gender and age. I propose in this study a small-sized, information-, high-tech- and leisure-oriented design that corresponds with the actual housing preferences of the single-person households.

• Korean Institute of Interior Design Journal
• /
• v.14 no.4 s.51
• /
• pp.79-86
• /
• 2005

According to the new multi-media appeared as a result of rapid growth of the information and science technique, the school library must be changed to the integration of the teach-study media resource from the existing print media. It means that the school library has to play a role of the study center with a different media from the existing teaching material, teaching instrument, facility and opportunity. The Information education must be conducted in the way of an integrated education course and able to do both information transaction and problem settlement. The education facility to solve this problem is the school library. Therefore, the school library becomes important more and more. It means that the school library is the center of entire study and education material for the teacher and student is focused on it. It is urgent to make the standard of the school library In order to cope with the new education and information environments. And especially it is very important to make a plan about the location and scale of the school library to improve the quality of the children's studying activity. The location of the school library is decided under consideration of the relationship with other room of school house and the proper scale of it is between 2.5units and 7.0units of classroom based on the number of class.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.5
• /
• pp.61-68
• /
• 2014

The energy efficiency of papermaking process becomes more significant because of various new regulation of the energy consumption and the green house gas emission. In this study, the effects of wood powder addition on the drainage and the drying efficiency of the OCC based paper products, linerboard, were deeply investigated for improving energy efficiency. The fractionation of wood powder depending on the size were conducted. The bigger size of wood powder resulted in the higher bulk and the higher drainage efficiency, but the lower paper strength. The drying efficiency were in detail evaluated depending on the drying process level. In the first section of drying process until the 80% solid level, there were no significant changes in the drying efficiency by the addition of wood powder. However, after the 80 % solid level, the drying efficiency was greatly improved by the addition of wood powder. Those results showed the addition of wood powder could greatly affect not only the drainage in forming and wet pressing but also the drying process.

• Korean Journal of Breeding Science
• /
• v.42 no.5
• /
• pp.431-438
• /
• 2010

Anthers of sweet pepper $F_1$ cultivar 'Special' were cultured on Dumas De Vaulx (C medium), supplemented with $0.1mgL^{-1}$ 2, 4-D and $0.1mg{\cdot}L^{-1}$ kinetin with 3% sucrose, and 0.32% phytagel. The calluses obtained were further sub-cultured on Murashige and Skoog (MS) medium without growth regulators for regeneration. Regenerated plantlets were grown in plastic pots under plastic house and characterized their cytological and morphological characters in spring, 2008. Twenty percent plantlets were identified as haploid plants after chromosome and ploidy analysis. Haploid plants contained 12 chromosomes, high stomatal density with small stomatal length as compared to diploid plants. Stomatal length in haploids was 23.3% smaller than diploids. Haploid plants were characterized as small leaf and petiole size, poor vigor, thin stem and short plant height, short internodes and small flower buds, fruit size and fruit weight as compared to diploid plants and most of the haploid fruits were seedless. SP55, SP62, SP68, SP72 and SP77 are found high yielding double haploids with high total soluble content (8.6, 8.7, 9.2, 9.1 and $9.8^{\circ}Brix$, respectively) and desirable fruit shape, and recommended them to exploit as inbred lines for heterosis breeding.

• STI Policy Review
• /
• v.9 no.1
• /
• pp.77-98
• /
• 2018

In the past few decades, the importance of dynamics of University-Industry Linkage(UIL) in strengthening national and regional innovation competency and global competitiveness has been progressively more acknowledged. However, establishing an effective UIL for a better economic development is still a challenging endeavor in Ethiopia, particularly in Tigray region. This study is aimed at assessing the status of UIL and in order to achieve such aim it analyzed the determinants of firms' intensity of interaction with the Mekelle University (MU) and the effect of the intensity of interaction on the relevant firms' innovation performance. The findings of the study showed that the status of UIL between the firms and the university in Tigray region was at an infant stage. The study also found that firm size, firm age (startups) and government supports have had a significant effect on firms' intensity of interaction with the MU. However, the firms' intensity of interaction with the MU did not have any significant effect on the firms' innovation performance. In contrast, cooperation with customers, other groups and suppliers, firm size, firm age, and in-house R&D activities were found to have a significant effect on the firms' innovation performance. In conclusion, the acquisition of knowledge and technology from university does not have an important role in firms' innovation performance in the studied region. Consequently, the government should design effective strategies and assign responsible bodies to implement the strategies, create awareness, and organize both firms and university to meet and work together in order to enhance firms' innovation performance.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.3
• /
• pp.11-18
• /
• 2019

The purpose of this study was to estimate the resistance capacity of a traditional wooden house with shear walls made of wood panel. In order to achieve the purpose of the study, the load - displacement test was carried out and the resistance moment values of the shear walls were proposed. The shear walls were made by placing studs with a nominal dimension of $38mm{\times}89mm$ at intervals of 600 mm, and attaching 12 mm thick plywood with 8-d size pegs at intervals of 150 mm. The type of traditional building wall was classified and showed the moment resistance ability of each wall type. This value is expressed as a proportional value divided by the moment resisting capacity of the standard size shear walls not divided into the divided small frames. Although some frames have proportional values larger than 1.0 even though they have openings, most of them show values smaller than 1.0. Also, even without the openings, it showed a smaller value than 1, such as 0.84 and 0.67.

• Nuclear Engineering and Technology
• /
• v.54 no.9
• /
• pp.3205-3214
• /
• 2022

The aim of this study is to provide a clear and accessible method to obtain accurate true-stress strain data, and to extend the limited material data beyond the ultimate tensile strength (UTS) for AISI 304L. AISI 304L is used for the outer construction for some types of nuclear transport packages, due to its post-yield ductility and high failure strain. Material data for AISI 304L beyond UTS is limited throughout literature. 3D digital image correlation (DIC) was used during a series of uniaxial tensile experiments. Direct method extracted data such as true strain and instantaneous cross-sectional area throughout testing such that the true stress-strain response of the material up to failure could be created. Post processing of the DIC data has a considerable effect on the accuracy of the true stress-strain data produced. Influence of subset size and smoothing of data was investigated by using finite element analysis to inverse model the force displacement response in order to determine the true stress strain curve. The FE force displacement response was iteratively adapted, using subset size and smoothing of the DIC data. Results were validated by matching the force displacement response for the FE model and the experimental force displacement curve.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.05a
• /
• pp.14-15
• /
• 2021

Recently, the size of tiles used for bathroom walls in apartment houses is gradually increasing in size. The problem is that when these large-sized tiles are attached by the sticking method, due to the nature of the method, there is a concern about the stability of the attachment to the part (pupil) where the tile and the adhesive are not attached. The problem is serious as it leads to lawsuits in the outbreak court. In addition, it is urgent to verify the adhesion stability of the sticking method because secondary damage occurs due to a safety accident caused by the falling of the tile. Ministry of Land, Infrastructure and Transport [Investigation of defects in apartment houses, calculation of repair cost and defect determination criteria] ① The tile adhesion strength is 0.39N/mm² or more and ② It is specified to fill 80% or more of the base area of the tile backside, but this is currently trendy. It is considered that large-sized tiles need to be verified from multiple angles, and as part of that, we intend to verify the adhesion stability according to the area to be attached to large-sized tiles.