• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.17-24
• /
• 2004

As the environmental pollution becomes serious global problem, the regulation of emission exhausted from automobiles is strengthened. Therefore, it is very important to know how to reduce the NOx and PM simultaneously in diesel engines, which has lot of merits such as high thermal efficiency, low fuel consumption and durability. By this reason, the new concept called as Homogeneous Charge Compression Ignition(HCCI) engines are spotlighted because this concept reduced NOx and P.M. simultaneously. However, it is well known that HCCI engines increased HC and CO. Thus, the investigation of combustion characteristics which consists cool and hot flames for HCCI engines were needed to obtain the optimal combustion condition. In this study, combustion characteristics for direct injection type HCCI engine such as quantity of cool flame and hot flame, ignition timing and ignition delay were investigated to clarify the effects of these parameters on performance. The results revealed that diesel combustion showed the two-stage ignition of cool flame and hot flame, the rate of cool flame increase and hot flame decrease with increasing intake air temperature. On the other hand, the gasoline combustion is the single-stage ignition and ignition timing is near the TDC. In addition mixed fuel combustion showed different phenomenon, which depends on the ratio of gasoline component. Ignition timing of mixed fuel is retarded near the TDC and the ignition delay is increased according to ratio of gasoline.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.287-290
• /
• 2005

Once hot forgings for automotive parts such as wheel bearing flange to which cyclic asymmetric bending stress is continuously applied are produced, it is necessary to control their microstructure to obtain superior mechanical properties. It is however hard to control the microstructure uniformly because the strength is reduced as coarsening of ferrite grains. To investigate the microstructural alteration according to process variables during hot working, the variation of the ferrite grain size was studied by utilizing of the computer aided servo-hydraulic Gleeble tester which is hot deformation behavior reproduction equipment. In addition, the effect of the ferrite grain size of raw material on the austenite grain behavior of hot forgings was also examined. The rolling contact fatigue resistance of the induction hardened SAE 1055 steel was compared with the occasion of the same condition of SAE52100 bearing steel. As a result, it was confirmed that the ferrite grain sizes of the forgings depend on the heating temperature and cooling start temperature during hot forging and cooling processes. The induction hardened SAE1055 steel showed a superior rolling contact fatigue resistance to the induction hardened SAE52100 steel. The reason is that SAE1055 steel is freer from the material defect such as segregation than the comparative steel.

• 한국자동차공학회논문집
• /
• 제14권3호
• /
• pp.58-67
• /
• 2006

In this paper, fuzzy logic based active ventilation system with security function is proposed and implemented. We can easily experience the situation that inner air is so hot to get start immediately after parking at summer day. Hot temperature is enough to explode a gas lighter or to suffocate a little chid. Proposed system has 1 blower and 2 axial fans to ventilate inner air. Based on the fuzzy logic, speed and direction of each fan are controlled. In addition to controlling fans, controller put down windows and adjust the periods of open time. In order to prevent the theft and security problems, IR sensors are used to detect objects. On detecting objects, controller put up windows. Experimental result shows that implemented system can be effectively ventilate inner air and reduce temperature. Proposed system can be applicable to commercial automobiles.

• 설비공학논문집
• /
• 제21권12호
• /
• pp.695-702
• /
• 2009

Dynamic behavior of Libr-water absorption system using low-temperature hot water was investigated numerically. Thermal-hydraulic model of single-effect/double-lift 100 RT chiller was developed by applying transient conservation equations of total mass, Libr mass, energy and momentum to each component. Transient variations of system properties and transport variables were analysed during start-up operation. Numerical analysis were performed to quantify the effects of bulk concentration and part-load operation on the system performance in terms of cooling capacity, coefficient of performance, and time constant of system. For an absorption chiller considered in the present study, optimum bulk concentration was found to exist, which resulted in the minimum time constant with stable cooling capacity. COP and time constant increased as the load decreased down to 40%, below which the time constant increased abruptly and COP decreased as the load decreased further.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.5-9
• /
• 2010

본 논문에서는 75톤급 액체로켓엔진 1/2.5-scale 연소기의 연소시험에서 얻어진 동적특성 결과에 대해 기술하였다. 엔진 시동 구간 및 연소실 압력에 따른 동적특성 변화를 살펴보기 위해 연소실 압력 30 bar와 60 bar 상태에서 연소시험이 수행되었으며 이에 따른 연소기의 연소안정성을 검토하였다.

• 한국수소및신에너지학회논문집
• /
• 제24권1호
• /
• pp.70-75
• /
• 2013

It has fabricated membrane electrode assemblies (MEA) for proton exchange membrane fuel cell by hot-pressing method. The hot-pressing was used for the fabrication of MEA which is composed of commercial platinum electrode on carbon paper. The performance of MEA was studied with different fabrication conditions of temperature, pressure and torque. As the temperature increased, the performance of MEA was increased. and started to decrease l after arrived at the maximum performance of MEA. This is related with good contact between electrode and polymer electrolyte membrane at high temperature and microstructural change at much higher temperature. Similarly, as the pressure increased, the performance of the MEA increased up to highest values and start to decrease. According to the our results, the maximal performance of the MEA was at the temperature of $140^{\circ}C$ and the pressure of $1.5{\times}10^3$ kPa. The optimal torque to assemble the single stack was 3.2 N m.

• 한국자동차공학회논문집
• /
• 제23권4호
• /
• pp.410-419
• /
• 2015

In this study, the roadability, fuel economy and emission characteristics were evaluated for a natural gas converted vehicle. The results are as follows; Not only the shortage of power was observed in stall test, but also large deterioration of acceleration performance was exposed in roadability. Compared to the original LPG system, the acceleration is 76% in start acceleration and 45 ~ 65% in overtaking acceleration, especially the decline became larger when air conditioner is at work. Furthermore, because the mapping data, which controls the injection depending on driving condition, do not match up with injection system, the failure of air-fuel ratio feedback control occurs resulting from the large gap between the required and the really supplied amount of fuel. This failure cause the exhaust gas to emit without catalytic conversion and the fuel economy based on the fuel heat value to get worse 22% in the mode test and 16% in road test respectively. In addition, the existing injection system does not secure enough fuel at the starting so that it may lead to the fail of clod start, the deterioration of hot start and inharmonic of engine at the idle after start.

• 한국추진공학회지
• /
• 제3권4호
• /
• pp.38-43
• /
• 1999

본 연구는 액체 추진제 로켓 엔진의 연소성능을 평가할 수 있는 절차를 확립하고, 운동량비와 혼합비가 연소성능에 미치는 영향을 고찰하여 안정된 연소를 보장하면서 최대의 효율을 제공하는 설계조건을 결정하고자 수행되었다. 연구를 위해 질산/Kerosene을 추진제로 사용하고 추력 24 $\iota{b}_f$, 연소실 압력 200 psia, uni-element impinging streams doublet injector를 사용하는 엔진을 설계 및 제작하여 연소시험을 수행하였다. 연구로부터 점화시 발생하는 hard start 현상은 연소실 압력을 설계치의 25 % 정도가 되도록 한 후, 설계 압력으로 상승시키는 2단계 점화방법을 채택함으로서 최소화 할 수 있었다. 그리고 최대의 연소성능은 혼합비 3.6에 존재하였고, 연소성능은 운동량비 증가에 따라서 감소하였다.

• 한국분무공학회지
• /
• 제23권2호
• /
• pp.66-73
• /
• 2018

Volatile organic compounds (VOCs) are well known as ozone precursors from photochemical reactions and contribute to the formation of photochemical smog which pose health hazards. Also, some of these compounds directly affect the human health due to their toxicity such as benzene. In this study, NMVOCs composition in exhaust gas from recreational vehicle (RV) and (MPV) were characterized using a chassis dynamometer. The results for NMVOCs have reported that alkanes emission was higher than alkenes, aromatics and cycloalkanes due to reactive of diesel oxidation catalysts. The NMVOCs composition according to carbon number was highly distributed between C3 and C6~C8. During the engine cold start condition, NMVOCs emission was higher compared to the engine hot start condition due to the increased catalytic activity. The NMVOCs emission with DPF increased compared to that without DPF. The results of this study will be provide to calculate VOCs emissions from mobile source.

• 한국지열·수열에너지학회논문집
• /
• 제18권4호
• /
• pp.33-44
• /
• 2022

In this study, we analyze the existing heating and cooling operation method for an office-type complex building with a central heating and cooling system, and examine the effects of applying various EMS that can be applied according to the load size to save energy in the building. For this purpose, simulation analysis was performed. As a control method, reset control of chilled water, hot water, cooling water and supply air temperatures, optimal start/stop of heat source, and number of heat source control were applied according to the load size, and energy consumption was analyzed accordingly. In addition, when all of these control methods were applied, the overlapping energy saving effect was finally confirmed. As a result, it was possible to confirm the energy saving effect when EMS for reset control and heat source control were applied compared to the existing control method of the heating and cooling system, and the effect for the case of using all these control methods in combination was also confirmed.