• 대한기계학회논문집B
• /
• 제20권8호
• /
• pp.2601-2610
• /
• 1996

Surface protrusions have been attached on a cylinder surface to reduce the flow-induced structural vibration by controlling the wake flow. Wind tunnel tests on the near wake of a circular cylinder with surface protrusions were carried out to investigate the flow characteristics of the controlled wake. Three experimental models were used in this experiment; one plain cylinder of diameter D and two cylinders wrapped helically by three small wires of diameter d=0.075D with pitches of 5D and 10D, respectively. Free stream velocity was ranged to have Reynolds number from 5000 to 50,000. Streamwise and vertical velocity components of the wake were measured by a hot-wire anemometry. The spanwise velocity component measured by a one-component fiber optic LDV revealed that time-averaged wake field has a nearly two-dimensional structure. It was found that the surface protrusions elongate the vortex formation region, which decrease the vortex shedding frequency. The suppression of vortices caused by the surface protrusions increases the velocity deficit in the center of wake region.

• Journal of Mechanical Science and Technology
• /
• 제15권7호
• /
• pp.895-905
• /
• 2001

This paper presents vector fields, three dimensional mean velocities, turbulent intensities, turbulent kinetic energy and Reynolds shear stresses measured in the X-Y plane of the gas swirl burner with a cone type baffle plate by using an X-type hot-wire probe. This experiment is carried out at the flow rates of 350 and 450ℓ/min which are equivalent to the combustion air flow rate necessary to release 15,000 kcal/hr in a gas furnace. The results show that the maximum axial mean velocity component exists around the narrow slits situated radially on the edge of a burner. Therefore, there is some entrainment of ambient air in the outer region of a burner. The maximum values of turbulent intensities occur around the narrow slits and in front of a burner up to X/R=1.5. Moreover, the turbulent intensity components show a relatively large value in the inner region due to the flow diffusion and mixing processes between the inclined baffle plate and the swirl vane. Consequently, the combustion reaction is expected to occur actively near these regions.

• Journal of Mechanical Science and Technology
• /
• 제15권7호
• /
• pp.906-920
• /
• 2001

This paper presents three-dimensional mean velocities, turbulent intensities and Reynolds shear stresses measured in the Y-Z plane of the gas swirl burner with a cone type baffle plate by using an X-type hot-wire probe. This experiments is carried out at the flow rate of 450ℓ/min which is equivalent to the combustion air flow rate necessary to heat release 15,000 kcal/hr in a gas furnace. Mean velocities and turbulent intensities etc. show that their maximum values exist around the narrow slits situated radially on the edge of and in front of a burner. According to downstream regions, they have a peculiar shape like a starfish because the flows going out of the narrow slits and the swirl vanes of an inclined baffle plate diffuse and develop into inward and outward of a burner. The rotational flow due to the inclined flow velocity going out of swirl vanes of a cone type baffle plate seems to decrease the magnitudes of mean velocities V and W respectively by about 30% smaller than those of mean velocity U. The turbulent intensities have large values of 50%∼210% within the range of 0.5

• 대한기계학회논문집B
• /
• 제21권5호
• /
• pp.700-712
• /
• 1997

The flowfield generated by a 2-D rotating cylinder on a plane moving at freestream velocity was experimentally investigated in a wind tunnel to simulate aerodynamic characteristics of rotating wheels of an automobile. In the flowfield around a rotating cylinder at 3*10$^{3}$ < Re$_{d}$<8*10$^{3}$, unique mean flow and turbulence characteristics were confirmed by hot-wire measurements as well as frequency analysis, which was supported by flow visualization. In the vicinity of a rotating cylinder, a unique turbulence structure on .root.over bar u'$^{2}$ profiles was formed in hump-like shape at 1 < y/d < 3. A peak frequency which characterized the effect of a rotating cylinder had the same value of the rotation rate of a cylinder. In case of cylinder rotation, the depths of mean velocity -defect and turbulent-shear regions were thickened by 20-40% at 0 < x/d < 10 compared with the case of cylinder stationary. Far downstream beyond x/d > 10, the flowfield generated by a rotating cylinder showed self-similarity in the profiles of mean velocity and turbulence quantities. The effect of a rotating cylinder was independent of its rotation rate and Reynolds number in the measurement range.

• 국제학술발표논문집
• /
• The 6th International Conference on Construction Engineering and Project Management
• /
• pp.411-414
• /
• 2015

The purpose of this study is to conduct a comparative analysis between Korea and the United States of the supply process of unit modular housing at both the factory production phase and the transportation and lifting phase, as part of an attempt to invigorate the unit modular housing market in Korea. Unlike the practice in the United States, one of Korea's unique characteristics is that the floor is constructed with reinforced concrete and hot water heating system. To do this, the wet method in Korea is used that includes concrete placement, curing and constructing hot water floor heating system at the factory production phase, which results in a longer production time and also requires the lifting of heavier loads. In the United States, interior and exterior finishing works of modular housing are performed by different companies, and the distance between the unit module factory and the construction site is quite far. This kind of dualized production structure may cause confusion when it comes to schedule management, procurement management, and stock management. Moreover, problems caused by external environmental factors such as wind and rainfall were reported in the course of long-distance transportation. The results of this case comparison are expected to provide fundamental data that will reduce the amount of trial and error in the unit module production, transportation and lifting work in Korea, which has a comparatively small number of unit modular housing cases.

• 에너지공학
• /
• 제19권4호
• /
• pp.228-233
• /
• 2010

기존의 열풍건조기의 효율은 약 30% ~ 50%인 반면, 최적 설계된 열풍-열펌프 건조기 효율은 약 60% ~ 80% 수준이므로 에너지 효율향상과 에너지 절약을 이룰 수 있다. 외국의 여러 사례에서는 기존 대비 약 60% ~ 80%의 에너지를 절약할 수 있으며, 밀폐형 순환방법을 사용하여 건조공기에 포함될 수 있는 환경오염물질의 외부로의 유출을 최소화 할 수 있어 기존의 건조기에 비해서 환경문제에 적극적으로 대응할 수 있을 것을 판단된다. 본 논문에서는 이와 같은 특성을 가진 건조기에 적용하기 위한 고온 생산이 가능한 열펌프를 얻기 위하여 시스템의 사이클을 설계하고 시스템을 구축하여 목표 성능을 만족하는지 여부를 확인하였다. 본 연구에서는 열펌프 복합건조기 적용을 위한 고온용 열펌프 시스템을 설계하고 제작한 후, 성능평가를 수행하여 다음의 결론을 얻었다. (1) 고온생산을 위한 시스템 설계는 2사이클이 가장 우수한 것으로 나타났다. (2) 2사이클 시스템은 저단이 R134a를, 고단이 R124를 냉매로 사용할 경우 가장 적합한 것으로 나타났다. (3) 사이클 운전을 통하여 상용압력으로 간주되는 범위에서 R134a시스템은 $75^{\circ}C$, R124시스템은 $95^{\circ}C$ 생산이 가능한 것으로 나타났다. (4) 수냉식 2사이클 시스템의 성능 시험을 수행한 결과 목표성능을 상회하는 결과를 얻어 고온 생산이 가능한 열펌프 시스템의 설계 및 제작이 가능한 것으로 나타났다.

• Journal of Preventive Medicine and Public Health
• /
• 제2권1호
• /
• pp.81-87
• /
• 1969

Three Combinations of cloths were evaluated for the protective effects of different kinds of clothings in cold environments. Table 1 shows the components of the three models of clothings. A prototype was made by putting a sheet of vinyl at the middle layer of raw cotton in a fabric-quilt cloths. A glove mannequin was covered by each of these cloths. The globes contained 1,000 cc of hot water about $40^{\circ}C$. Tele-thermistors were fixed in order to check the temperature of cloths space and water temperature for evaluation of calorie-loss and climate of clothings. Results are summarized as follows: 1) Without wind, there is no significant difference of air temperatures between sti-parka and quilt-wear clothing. 2) The prototype with vinyl sheet best protects against wind, the next is the ski-parka. Quilt-wear protects the least. 3) It is well-known that a working-clothing needs not have any separate liners nor outers. 4) For innermost layer of a clothing preventing cold, a cotton-fabrics is recommended and a water-proof cloths for outer layer. 5) Heat-loss was calculated from the cooling degrees of water. Calorie-loss was $910cal/m^2/hr$. when bared, but with the prototype of vinyl sheets the calorie-loss was $350cal/m^2/hr$. (38.5% of bared). Quilt-wear and ski-parka were 380(41.8%) and $440cal/m^2/hr$. (48.4%) respectively.

• KIEAE Journal
• /
• 제3권3호
• /
• pp.19-25
• /
• 2003

The Address No.0 of Eco-friendly Architecture offers unique experience for those who visit the place to envisage the future architecture where nature, human and building exist in harmony. It is open to the general public including the students of elementary and secondary schools. This house has been built to provide opportunities for the general public to experience eco-friendly architecture. It's floor area is 42 pyung($140m^2$) and the overall site has the area of 180 pyung($600m^2$). The following illustrates some of its prominent features : ${\bullet}$ Remodeling of a traditional Korean residence ${\bullet}$ Application of passive solar systems ${\bullet}$ Use of clerestory windows and daylighting systems(washroom and machine room) ${\bullet}$ Operation of solar water heaters with flat plate collectors ${\bullet}$ Construction of Biotop(small ecological world) ${\bullet}$ Water circulation for Biotop by photovoltaic(150W) and wind power(400W) generation ${\bullet}$ Outdoor hot water supplied by all-glass evacuated solar tubes. Through this Address No.0 of Eco-friendly Architeture conclusions are as followings. 1. The array of tubes in collector has the best nice in that the number of tube is nine and the tilt angle is the latitude $+20^{\circ}$. 2. The thermal performance of the all-glass solar vacuum collector was excellent than of the flate-plate solar collector. 3. The adaption of new small wind power systems to buildings were proved to produce a profit if it is considered the expense of environment improvement and the wind speed increasing according to rise of building hight.

• 한국조경학회지
• /
• 제40권1호
• /
• pp.1-11
• /
• 2012

이 연구는 인간 에너지 균형 모델에서 출발한 인간 열환경 지수 분석 방법을 이용하여 캐나다 BC주에 있는 나나이모시 상업지구안 좁은 길과 경상남도 창원시 중심상업지구에 있는 소공원을 연구 대상지로 2009년 여름철 열환경을 분석한 것이다. 기후 입력 자료는 기온, 상대습도, 풍속, 태양 및 지구 복사에너지이었으며, 그 결과 인간 열환경 지수에 가장 크게 영향을 미치는 요소들은 태양 직사광선, 건물시계지수 그리고 풍속이었다. 음지는 약간 더운 정도의 열환경을 조성하는 것으로 나타나 매우 덥게 나타난 양지에 비해 훨씬 좋은 열환경을 조성하는 것으로 나타났다. 나나이모 연구 대상지에 있는 좁은 길들은 주변의 넓은 장소들에 비해 주변 건축물에서 나오는 태양 반사광선과 지구 복사에너지들이 더 많이 영향을 미쳐 훨씬 덥게 나타났다. 낮은 풍속에 의해서 인체에서 방출되는 현열과 잠열의 양이 현저히 줄어듦으로서 더 더운 열환경이 조성되는 것으로 나타났다. 기후요소를 조경에 접목하기 위해서, 인간 열환경 지수 분석 방법을 이용하는 것은 열환경적으로 쾌적한 옥외 공간조성에 영향을 미칠 것이며, 도시 열섬 완화와 기후변화 연구에도 잘 이용될 수 있을 것이다.

• 한국농림기상학회지
• /
• 제11권4호
• /
• pp.192-205
• /
• 2009

2009년 2월 9일 화왕산에서는 대보름 행사인 '억새 태우기'가 많은 사람들이 지켜보는 가운데 시작되었지만 예상하지 못한 강풍으로 산불로 확대되어 많은 인명피해가 발생하였다. 본 연구에서는 3차원 계산 유체역학 모형인 CFD_NIMR_SNU 모형을 이용하여 복잡한 산악지역에서 국지적 가열에 따른 바람장을 모사함으로써 이날 발생한 산악 화재의 특성을 분석하였다. 화재가 발생한 지역의 지표 온도는 가열이 없을 때, $300^{\circ}C$ 및 $600^{\circ}C$ 일 때의 3가지 가열 강도조건을 주어 모사하였다. 지표 가열은 화재 발생 지역 중앙에서 수직 바람장을 $0.7m\;s^{-1}(300^{\circ}C)$와 $1.1m\;s^{-1}(600^{\circ}C)$만큼 증가시켰다. 난류운동에너지는 화재의 열에너지 자체 및 열적 순환에 의해 증가된 운동에너지에 의해 증가하였다. 화재로 인한 열은 복잡한 지형과 강한 경계 바람 조건과 함께 화왕산의 예상하지 못한 난류와 강풍 조건을 유도하였다. CFD_NIMR_SNU 모형은 인명피해를 발생시킨 산불을 이해하는데 도움이 되는 귀중한 분석 자료를 제공하였다. 모사 결과에 따르면 화재 발생 지점은 풍상측의 높은 지형으로 인하여 화재 발생 직전까지는 바람이 거의 억제되었던 것으로 보인다. 이러한 바람의 억제는 화재 발생에 따른 뜨거운 공기의 상승과 강한 경계 바람 조건에 의해 쉽게 되돌려졌다. 즉, 강한 경계 바람과 화재로 인한 가열이 함께 작용하여 강한 난류가 만들어졌고, 여러 명의 사상자가 발생한 산악 화재로 확산되었던 것이다. CFD_NIMR_SNU 모형은 중규모 모형과의 결합을 통하여 좁은 영역의 화재로 인한 난류 예보를 생산하는 등 산불 예방을 위해 활용될 수 있을 것이다.