• Korean Journal of Metals and Materials
• /
• v.48 no.5
• /
• pp.387-393
• /
• 2010

High-strength aluminum alloy sheets with high magnesium contents were fabricated by a strip caster equipped with an asymmetric nozzle, which has been proven to be effective for reducing surface defects and internal segregation. 4 mm thick as-cast sheets consisting of fine dendrites and minor $Al_{8}Mg_{5}$ segregation were hot-rolled successfully to 1 mm sheets and subsequently annealed at various temperatures. The sheet revealed the tensile strength and elongation of 306 MPa and 34%, respectively, when it was rolled at 250${^{\circ}C}$ and subsequently annealed at 475${^{\circ}C}$, which exhibits the feasibility of the practical application for autobodies. The observed mechanical properties were explained on the basis of the microstructural characteristics of the alloy sheets.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.512-517
• /
• 1993

The cold rolled strip meets continuously rising demands on the less deviation of thickness at the width direction of their rolled products. Especially, the special interest has been to find the methods to reduce the edge drop which influences seriously on the yield losses and the quality of the rolled products. In this study, the influence of hot coils on the thickness profile of cold rolled strip was analyzed. For obtainint the tapered work roll shig\ft conditions, the thermal crown and the flattening between the work roll and the strip were calculated, and the main parameters which have mostly effects on the edge drop were simulated. Also the obtained conditions from the simulation were applied to Tandem Cold Rolling Mill to investigate the change of the edge drop and the crown ratio depending on the amount of work roll taper and the length of contact of taper. The results of the application led to better thickness profile than conventional one.

• Journal of Surface Science and Engineering
• /
• v.34 no.2
• /
• pp.115-124
• /
• 2001

Gas wiping process of continuously hot-dip galvanized coating on steel strip has noise and coating problems. To improve the qualify of product, characteristics of air flow on the steel surface must be investigated. In this paper, fluid dynamic model of the gas flow is setup and solved numerically using STAR-CD. The effects of edge baffle, distance between steel plane edge and baffle, inlet pressure, and gap between air knife and strip steel surface are investigated, and it is concluded that edge baffle can reduce over-coating and edge built-up.

• Transactions of Materials Processing
• /
• v.18 no.1
• /
• pp.52-58
• /
• 2009

Generally, a vertical rolling process is used to achieve extensive width reduction in hot strip mill. However, it is impossible to avoid the defects such as dog-bone and edge-seam defect. The sizing press process has been developed in response to the defects mentioned above. Especially, this study is carried out to investigate the deformation of slab by two-step sizing press. The deformation behavior of slab in the sizing press process is more favorable than that in conventional vertical rolling edger. The FE-simulation is applied to predict the deformation behavior of the slab. In this paper, the several causes of the asymmetrical deformation are mentioned for the purpose of understanding of the anvil shape. Load, dog-bone and edge-seam defect are discussed in width sizing process considering the anvil shape. And to reduce the problems generated at rougher mill just after sizing press, these are studied in this paper. The deformation behavior of slabs and optimum anvil shape are obtained by rigid-plastic finite element analyses and neural network.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.142-146
• /
• 2001

In this study, it was investigated the influence of cold rolling factors on the edge drop. Edge drop was highly affected by the shape of work roll, the amount of work roll shift and the crown of hot strip, but the effect of bending force at the front stand was relatively small. The used numerical model was examined by comparing to the result of measured field data, and it showed a qualitative agreement with each other.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.4
• /
• pp.387-394
• /
• 2016

Today, hot rolled mill plant are currently operating 24 hours a day. The main processes of hot-rolled steel mill are Reheating Furnace, Roughing Mill, Fishing Mill and the Down Coiler. In the process checking over the thickness and width of rolled material, temperature control is an important factor. It is quite often the cause of the work breakdown and find a bad elements for product. After the shipping out the product, when a claim occurs requires an investigation. In each process of the conventional thickness gauge, width, and thermometer. Operation by an independent data acquisition and this monitoring is problematic and straining of the operator. The monitoring process the data of each function and incorporate monitoring results can also check future work. The installation of this system will improve our efficiency and productivity. In the rolling process by developing more efficient operating quality monitoring system, this will be made possible.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1996.03a
• /
• pp.101-109
• /
• 1996

Mini-mill process which is one of the new steel -marking technologies to be able to produce the hot rolled coils by thin slab caster of ISP(In-Line Strip Production) type, will be completed in the Kwangyang Steel Works of POSCO in August, 1996, SEt-Up Model of finishing mill which consists of 5 stands is the most basic and essential in mini-mill plant. Therefore, the simulation program of Finishing-mill Set-Up model were developed in this research , using new temeprature prediction model, roll gap model and rolling physical model. Using the developed FSU program , pass schedules to produce the strips with target strip thickness of 1.8mm, 2.0mm, 2.3mm, 2.7mm an d3.0mm were also determined respectively.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.03a
• /
• pp.233-237
• /
• 1995

Effects of frictional laws on finite element solutions in bulk metal forming were investigated in this paper. The Coulomb friction and the constant shear friction law were compared through finite element anlayses of compression of ring and cylinders with different aspect rations, ring-gear forging and hot strip rollin under the isothermal condition. It has been shown that two laws may yield quite different results inthe case that the aspect ration of a process is large, for example , strip rolling and ring -gear forging and that the difference depends mainly on the aspect ratio and the friction.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.249-252
• /
• 1997

Mini-mill process which is one of the new steel making process to be able to produce the hot rolled strip by thin slab caster, was completed in the kwangyang steel work. The new process was constructed liquid core deduction, tandem reduction unit, induction heater, coil box and finishing mill to be varied width. Therefore, in oder to make sure of target strip width, analysis of actual plant data was done to fine out amount of width deviation. Finally, the predication system of width in the mini-mill process was developed to included temperature caculation model.

• Transactions of Materials Processing
• /
• v.23 no.3
• /
• pp.139-144
• /
• 2014

In the current study, we present a new model for predicting width spread of a slab with a dog-bone shaped cross section during rolling in the roughing train of a hot strip mill. The approach is based on the extremum principle for a rigid plastic material and a three dimensional admissible velocity field. The upper bound theorem is used for calculating the width spread of the slab. The prediction accuracy of the proposed model is examined through comparison with the predictions from 3-D finite element (FE) process simulations.