• 조명전기설비학회논문지
• /
• 제27권6호
• /
• pp.59-67
• /
• 2013

This paper presents a neural net type process model for enhancing learning compensation function in hot strip finishing rolling mill. Adequate input and output variables of process model are chosen, the proposed model was designed as single layer neural net. Equivalent carbon content, strip thickness and rolling speed are suggested as input variables, and looper's manipulation variable is proposed as output variable. According to simulation result using process data to show the validity of the proposed process model, neural net type process model's outputs give almost similar data to process output under same input conditions.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.73.3-73
• /
• 2001

Finishing mill (FM) is set up with rolling conditions (rolling speed, rolling force, roll gap, etc.) calculated by a FSU (Finisher Setup) model considering the temperature, qualities and size of a transfer bar and a strip at the entry and exit of FM before the transfer bar is rolled through FM. If the accuracy of setup is low mass flow unbalance occurs, so that the accuracies of the strip thickness and width become lower or rolling operation fault occurs. Therefore, to enhance the performance of the FSU model and to improve mass flow and the thickness accuracy of a strip in the 7-stand finishing mill using a hot strip speed measurement system. This study is being performed. In this paper, the speed measurement system, a developed neural network for predicting ...

• 한국정밀공학회지
• /
• 제13권2호
• /
• pp.48-61
• /
• 1996

In the hot strip mill, not only the chatter vibration of finishing stands has a great influence on the surface quality of hot products, but also that is the major factors to shorten the life of rolling mill housings or to create the machine troubles. As long as the mill has been operating, the low frequency chatter at the early mill stands (No.2 and No.3) of POSCO's Kwangyang No.2 hot strip mill had been detected when rolling certain types of products, e.g., thinner gage, hard grade products. For several years, the experimental study was undertaken to analyze the cause of the chatter vibration and establish the methods to avoid the vibration to acceptable levels. The analysis and solution to the vibration problem with recommendations and revised maintenance practice are the subjects of this article.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.13-16
• /
• 2000

In the hot strip mill, a bad threading and shape of strip strip in the finishing mill was caused by asymmetric rolling In roughing min. Mathematical analysis for camber control of roughing mill in hot strip rolling has been developed. Each equation in the camber control model was derived from geometrical characteristics of camber mechanism. The model can predict variables such as wedge, side slippage and roll force difference etc. from a measured camber value and then find an optimum roll gap condition for minimizing camber in the next pass.

• 소성∙가공
• /
• 제8권6호
• /
• pp.583-590
• /
• 1999

New forward slip model has been developed for the precise prediction of rolling speed in the hot strip finishing mill. Besides those influential factors such as neutral point, work roll diameter, friction coefficient, bite angle and the thickness at each side of entry and delivery of the rolls, roll torque was specifically taken into account in this study. To consider the effect of width change on forward slip, calibration factors obtained from rolling torque has been added to new prediction model and refining method has also been developed to reduce the speed unbalance between adjacent stands. The application of the new model showed a good agreement in rolling speeds between the predictions and the actual measurements, and the standard deviation of prediction error has also been significantly reduced.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.169-169
• /
• 2000

The modeling for the looper of a hot strip finishing mill to control the tension of the strip is presented. The looper is an arm pushing against the strip between stands in a tandem mill to keep the strip tension constant and to isolate the interactions of the adjacent stands. Tension is influenced by the difference in mass flow through the up stream and down-stream rolling stands. Tension is critical to strip quality, influencing width, gauge, and shape. This paper presents how looper angle and strip tension are controlled for a hot strip finishing mill.

• Journal of Mechanical Science and Technology
• /
• 제18권6호
• /
• pp.972-978
• /
• 2004

Forward slip is an important parameter often used in rolling-speed control models for tandem hot strip rolling mills. In a hot strip mill, on-line measurement of strip speed is inherently very difficult. Therefore, for the set-up of the finishing mill, a forward slip model is used to calculate the strip speed from roll circumferential velocity at each mill stand. Due to its complexity, most previous researches have used semi-empirical methods in determining values for the forward slip. Although these investigations may be useful in process design and control, they do not have a theoretical basis. In the present study, a better forward slip model has been developed, which provides for a better set-up and more precise control of the mill. Factors such as neutral point, friction coefficient, width spread, shape of deformation zone in the roll bite are incorporated into the model. Implementation of the new forward slip model for the control of a 7-stand hot strip tandem rolling mill shows significant improvement in roll speed set-up accuracy.

• 소성∙가공
• /
• 제8권1호
• /
• pp.65-77
• /
• 1999

In recent years, the quality requirements from the customers of hot rolled steel strip have been steadily increasing in diversity and strictness. To meet these quality requirements as well as to improve productivity, steel mills have been doing their efforts for developing high performance Automatic Gauge Control (AGC) system. However, it is very time consuming and also needs a lot of money to develop the new technologies of AGC in actual mill. So, there has been a demand for developing the Dynamic Hot Rolling Simulator since late 80's. It is a kind of software packages and can analyze the dynamic behaviors of hot finishing rolling process without laborious experiments in actual mill. It can also be used as a designing tool of Automatic Gauge Controller. In this work, the Dynamic Hot Rolling Simulator which is applicable to 6 sands hot strip mill rolling was developed. The MATLAB with SIMLINK was used as a software developer for making the main part of simulator because it is very powerful tool for modeling, integrating, controller design, and simulation. In this paper, the structures and the mathematical models of the simulator were briefly described and the results of simulation on the transient phenomena of hot rolling process with actual mill data were also presented.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.368-373
• /
• 2003

A major concern at present is the simultaneous control of transverse thickness profile and flatness in the finishing stages of hot rolling process. The mathematical modeling of hot rolling process has long been recognized to be a desirable approach to investigate rolling operating practice and the design of mill equipment to improve productivity and quality. However, many factors make the mathematical analysis of the rolling process very complex and time-consuming. In order to overcome these problems and to obtain an accurate rolling force, the predicted model of rolling force using neural networks has widely been employed. In this paper, Radial Basis Function Network(RBFN) is applied to improve the accuracy of rolling force prediction in hot rolling mill. In order to verify and analysis the performance of applied neural network, the comparison with the measured rolling force and the predicted results using two different neural networks - RBFN, MLP, has respectively been carried out. The results obtained using RBFN neural network are much more accurate those obtained the MLP.

• 한국공작기계학회논문집
• /
• 제13권6호
• /
• pp.29-33
• /
• 2004

A major concern at present is the simultaneous control of transverse thickness profile and flatness in the finishing stages of hot rolling process. The mathematical modeling of hot rolling process has long been recognized to be a desirable approach to investigate rolling operating practice and the design of mill equipment to improve productivity and quality. However, many factors make the mathematical analysis of the rolling process very complex and time-consuming. In order to overcome these problems and to obtain an accurate rolling force, the predicted model of rolling force using neural networks has widely been employed. In this paper, Radial Basis Function Network(RBFN) is applied to improve the accuracy of rolling force prediction in hot rolling mill. In order to verify and analyze the performance of applied neural network the comparison with the measured rolling force and the predicted results using two different neural networks-RBFN, MLP, has respectively been carried out. The results obtained using RBFN neural network are much more accurate those obtained the MLP.