• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.2
• /
• pp.134-145
• /
• 1998

The purpose of this paper is to construct a computer simulation system which can analyze and design the hydraulic excavator Theoretical analyses are performed on the hydraulic circuit and attachment of excavator with load sensing system. Databases are constructed for control valve opening areas, horsepower control and for load sensing regulator. For hydraulic components modularized programming techniques are applied which is expected to be utilized for software development of fluid power system. Through simulation an information of any point in hydraulic circuit can be obtained.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2535-2542
• /
• 2000

The regulator system has been modeled and combined to a swashplate type axial piston pump. Linear approximation has been performed for nonlinear coefficient terms of an axial piston pump-regulator model without significantly affecting accuracy. Based on the mathematical model of an axial piston pump-regulator system, a couple of characteristic curves of negative flow control and horsepower control are drawn, which show a good correlation with those of experimental results. So the simplified axial piston pump-regulator model in this paper is expected to be utilized not only for the design and analysis of hydraulic circuit of excavator but also for prevention of engine overload.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.994-999
• /
• 2007

The particulate matters emitted by diesel locomotives cause serious air pollution in stations and railroad. There have been various attempt to reduce the air pollution from diesel bus or trucks. However, the air pollution from the diesel locomotives has been out of control because there has not any adaptable technology. In this study, a diesel particulate filter was developed and applied to the diesel locomotives. A 3,000 horsepower large-scale locomotive and a 1,500 horsepower middle-scale locomotive were used for the test of the filter. The particulate matter emissions before and after the treatment was monitored by a scanning mobility particle sizer and a dust monitor. As a result, it was observed that the particulate matters could be successfully removed from the emission gases by using the filter.

• Journal of Biosystems Engineering
• /
• v.9 no.2
• /
• pp.19-26
• /
• 1984

This study intended to develop the prediction models of the traction and field performance of two-wheel tractors by using the principles which were applied for predicting those of the four-wheel tractors. The traction model developed in this study consists of the net traction coefficient, rolling resistance coefficient and traction efficiency, Which are expressed as functions of both wheel numeric and slip. A computer program on the field performance of two-wheel tractors is also developed to predict the drawbar horsepower, traction force, traction efficiency, rotational speed of engine and engine horsepower if the characteristics of the engine performance and operational condition of the two-wheel tractor are known. Based on the developed models, the conditions of basic variables to maximize the field performance were analyzed so as to assess the existing two-wheel tractor.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.6
• /
• pp.599-605
• /
• 2013

The characteristics of centrifugal pump performance according to fluid viscosity change were studied experimentally. A small volute pump with low specific speed was tested by changing the viscosity of an aqueous solution of sugar and glycerin, which is considered a Newtonian fluid. After finishing the test, the total head, shaft horsepower, and pump efficiency were compared with those of a water pump. The results are summarized as follows: (1) when the fluid viscosity is increased, the shut-off head shows very little change but the total head decreases gradually as the flow increases, and this makes the H-Q curve leaning rapidly, and (2) when the fluid viscosity is increased, the shaft horsepower shows very little change at the shutoff condition; however, the shaft horsepower increases more rapidly with an increase in the flow and viscosity.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.53 no.4
• /
• pp.446-455
• /
• 2017

The improvement of resistance performance for the 4.99 ton class fishing boats was shown. The 4.99 ton fishing boats are the most commonly used one in the Korean coastal region. The evaluation of resistance performance was estimated by the Computational Fluid Dynamics (CFD) analysis. The CFD simulation was performed by the validation for various types of bow shapes on the hull. The optimized hull form from the simulation was selected and showed the best resistance performance. This hull type was tested on the towing tank in the National Institute of Fisheries Science (NIFS). The effective horsepower (EHP) was estimated by the resistance test on the towing tank with the bare hull condition. The drag force on the three service speed conditions was obtained for the resistance analysis to power prediction. The measured drag forces are compared with the results from the CFD simulation with one another. As results of the model tests, it was confirmed that the shape of the bow is an important factor in the resistance performance. The effective horsepower decreased about 30% in comparison with the conventional hull form. Also, the resistance performance improved the reduction of required horsepower, which especially contributed to the energy-saving for the fisheries industry. In the CFD analysis, the resistance performance improved slightly. In this case, the ratio of the residual resistance ($C_R$) in the total resistance ($C_T$) was high. Therefore, the CFD analysis was not enough to satisfy with reflection for the free surface and wave form in the CFD procedure. Both model test and CFD calculation in this study can be applied to the initial design process for the coastal fishing vessel.

• International Journal of Highway Engineering
• /
• v.15 no.4
• /
• pp.177-186
• /
• 2013

PURPOSES: The purpose of this study theoretically reviews vertical grade deriving process in super high speed environment and compares overseas design criteria with Domestic Standardization also draws suitable vertical grade design criteria of high standard for Domestic Circumstances in Korea. METHODS : By researching domestic vehicle registration status, calculating typical vehicle, using Vissim which is traffic simulation program, Speed-distance curve of the vehicle is derived under each design speed condition. Through Speed-distance curve, estimating critical length of grade and considering critical length of grade, maximum longitudinal incline is proposed. RESULTS : The result of domestic vehicle registration status, the typical vehicle for deriving vertical grade is calculated based on gravity horsepower ratio 200 lb/hp. For calculating critical length of grade, according to change speed of uphill entry, speed-distance curve is derived by using Vissim. Critical length of grade is calculated based on design speed 20 km/h criteria which is point of retardation. Estimated critical length of grade is 808 m and based on this result, maximum longitudinal incline was confirmed in the design speed between 130km/h to 140km/h. CONCLUSIONS: The case of the typical vehicle(truck) which is gravity horsepower ratio 200 lb/hp, maximum longitudinal incline 2% is desirable at the super high speed environment in the design speed between 130km/h to 140km/h.

• Journal of Korean Society of Transportation
• /
• v.25 no.5
• /
• pp.79-90
• /
• 2007

In determining vertical grades in highway alignment design, engineers usually consider heavy vehicle performances on the upgrade. Heavy vehicles usually experience speed reduction on the upgrade and with recent years weight/horsepower improvements for heavy vehicles the speed reduction shows some change. However, in spite of the weight to horsepower improvements for the design vehicles from 300lb/HP to 200lb/HP in the AASHTO, there was no change in the maximum vertical grades. Therefore, a review of the maximum vertical grade reflecting existing heavy vehicle performances is required. In particular, in South Korea where highways pass through lots of mountaineous terrain, the maximum vertical grades must be reviewed throughly. In this study the amount of heavy vehicle performances during past decades were investigated and their expected impacts on highway vertical alignment designs were subsequently analyzed. A worldwide terrain analysis and international design standards were compared to set South Korean vertical grade standards. Traffic flow simulation Vissim was utilized to simulate vehicular flows on the upgrade and new truck performance curves on the grades were developed. Based on the new curve, it was decided that $1{\sim}2%$ increase of the maximum vertical grades could be allowed.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.7
• /
• pp.851-857
• /
• 2019

This study is about ship horsepower prediction of machine learning method using the big data of ship. Currently, new ships use the ISO15016 method to predict external environmental resistance through mathematical equations but due to complicated equations and requires many input variables so it is less applicable to be used in ship. In this recent research, we propose a model capable of predicting ship performance with high performance using SVM (Support Vector Machine) algorithm which shows excellent performance in recent prediction and recognition. The proposed predictive model has the advantage of being able to predict better performance than ISO15016 only if secured big data is used. In this study, we compared the ISO15016 technique and the SVM algorithm-based horsepower analysis method using the 178K bulk carrier's voyage data to reduce ship model data preparation, which is a disadvantage of ISO15016, and improve inaccurate horsepower prediction performance.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.211-212
• /
• 2008