• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.11 s.176
• /
• pp.135-141
• /
• 2005

Measurement of five DOF motion errors in a ultra precision feed table was attempted in this study. Yaw and pitch error were measured by using a laser interferometer and roll error was measured by using the reversal method. Linear motion errors in the vertical and horizontal directions were measured by using the sequential two point method. In this case, influence of angular motion errors was compensated by using the previously measured ones by the laser interferometer and the reversal method. The capacitive type sensors and an optical straight edge were used in the reversal method and the sequential two point method. Influence of thermal deformation on sensor jig was investgated and minimized by the periodic measurement according to the variation of room temperature. Deviation of gain between sensors was also compensated using the step response data. 5 DOF motion errors of a hydrostatic table driven by the linear motor werer tested using the measurement method. In the horizontal direction, measuring accuracies for the linear and angular motion were within ${\pm}0.02\;{\mu}m$ and ${\pm}0.04$ arcsec, respectively. In the vertical direction, they were within ${\pm}0.02{\mu}m$ and ${\pm}0.05$ arcsec. From these results, it was found that the introduced measurement method was very effective to measure 5 DOF motion errors of the ultra precision feed tables.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.7
• /
• pp.81-88
• /
• 2004

In case of mechanical down tilting, a horizontal pattern is distorted and beam width widens whenincreasing tilt angle, which causes an expansion of hand off region and burden base station equipment. In contrast, electrical down tilting has advantage that horizontal HPBW is kept constant with down tilting. In this paper, based on a phased array technology, dual polarized base station antenna with electrical down tilting was developed at 800MHz band. The antenna has down tilting range of 0$^{\circ}$ to 14$^{\circ}$, and 15㏈i gain. We use stacked microstrip patch as a radiated element and apply balanced feed technique to improve isolation between ports and discrimination of cross polarization. The effect of electrical down tilting was verified by field test.

• Asian-Australasian Journal of Animal Sciences
• /
• v.28 no.5
• /
• pp.662-670
• /
• 2015

The objectives of this study were to investigate the effects of feeding barley naturally contaminated with Fusarium mycotoxins on growth performance, vulva swelling, and digestibility of dry matter, organic matter, and crude protein of gilts and the recovery of gilts fed normal diets immediately after the exposure to contaminated diets by measuring growth performance and vulva swelling. In Exp. 1, four diets were prepared to contain 0%, 15%, 30%, or 45% contaminated barley containing 25.7 mg/kg deoxynivalenol and $26.0{\mu}g/kg$ zearalenone. Sixteen gilts with an initial body weight (BW) of 33.3 kg (standard deviation = 3.0) were individually housed in a metabolism crate and assigned to 4 diets with 4 replicates in a randomized complete block design based on BW. During the 14-d feeding trial, individual BW and feed consumption were measured weekly and the vertical and horizontal lengths of vulva were measured every 3 d. From d 10, feces were collected by the maker-to-marker method for 4 d. Blood samples were collected on d 14. During the overall period, the average daily gain, average daily feed intake, and gain:feed of pigs linearly decreased (p<0.01) as the dietary concentration of contaminated barley increased. However, the digestibility of crude protein was linearly increased (p = 0.011) with the increasing amounts of contaminated barley. Increasing dietary Fusarium mycotoxin concentrations did not influence vulva size, blood characteristic as well as immunoglobulin level of pigs. In the Exp. 2, a corn-soybean meal-based diet was formulated as a recovery diet. Pigs were fed the recovery diet immediately after completion of the Exp. 1. During the 14-d of recovery period, the individual BW and feed consumption were measured weekly and the vertical and horizontal length of vulva were measured every 3 d from d 0. On d 7, the feed intake of pigs previously fed contaminated diets already reached that of pigs fed a diet with 0% contaminated barley and no significant difference in growth performance among treatments was observed during d 7 to 14 of the recovery period. In conclusion, increasing levels of mycotoxins in diets linearly decreased the growth performance of pigs, and these damages can be recovered in 7 d after the diet was replaced with a normal diet. The vulva size, blood characteristic, immune responses were not affected by increasing level of contaminated barley in the diets fed to pigs.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.20 no.43
• /
• pp.47-57
• /
• 1997

As a general index in surface quality of machined products, surface roughness is to measure worker's skill level, a ground product quality and machining accuracy, etc. The surface roughness is defined by a function of rotational speed and radius of a grinding wheel, distances of active grains composed of the wheel, and feed of a grinder's worktable. To predict surface roughness in horizontal surface grinding operations, probability distributions were used. Probability distribution functions(p.d.f.) of surface roughness were found as results when the size of active grains(=the radius of a grinding wheel) is given as uniform, exponential distribution, and the distance between active grains follows the distributions of uniform, exponential. For each pdf case, probabilistic features of surface roughness were also analyzed and presented. This study is a substantial step for determining mathematically the surface roughness instead of using empirical approaches. More works should be presented to develop a general model by which an accurate roughness value can be obtained in horizontal surface grinding operations.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.6
• /
• pp.1074-1079
• /
• 1987

We present a fast, constructive algorithm for the automatic placement of standard cells, which consists of two steps. The first step is responsible for cell-row assignment of each cell, and converts the circuit connectivity into a multi-stage graph under to constraint that sum of the cell-widths in each stage of the multi-state graph does not exceed maximum cell-row width. Generatin of feed-through cells in the final layout was shown to be drastically reduced by this step. In the second step, the position of each cell within the row is determined one by one from left to right so that the cost function such as the local channel density is minimized. Our experimental result shows that this algorithm yields near optimal results in terms of the number of feed-through cells and the horizontal tracks, while running about 100 times faster than other iterative procedures such as pairwise interchange and generalized force directed relaxation method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.653-657
• /
• 1996

This paper presents adaptive cutting force control in milling process using indirect cutting force measurement. The cutting forces in X, Y, and Z axes are measured indirectly from the sensing current of the feed-drive servo motor. After modelling the feed-drive system of a horizontal machining center, the relation between the cutting force and the servo motor current is analyzed. The pulsating milling forces are measured from the sensing current within the bandwidth of the servo. It is shown that indirect cutting farce measurement can be used in adaptive cutting force control. The adaptive control scheme which is globally convergent and stable is attached to a commercial CNC machining center. Cutting experiments on end milling are performed for diagonal cutting.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.1C
• /
• pp.94-101
• /
• 2008

In this paper, we introduce a real-time state-of-polarization(SOP) finding system. The system divides the optical wave into linear horizontal- and vertical-SOP components and measures two different beat-signals, which are produced by superposition with reference optical source, in time domain. From these measured beat signals we can get SOP information of the signal instantly. Since the proposed scheme is a feed-forward measurement system, comparing with conventional systems which require an optical feedback loop, the measurement time becomes reduced tremendously. We also introduced a novel calibration method for compensating birefringence-related errors which may occur during the measurement. We prove the operation and performance of the proposed system through computer simulation and actual experiments.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.11
• /
• pp.70-77
• /
• 2020

Vibratory bowl feeders are widely utilized to align and feed the parts stacked inside the bowl of a feeder. The electro-magnetic force of the electromagnet in a bowl feeder generates the excitation force for the bowl to vibrate in both the horizontal and vertical directions to continuously feed the parts on the track. The feed rate of the part depends on the associated displacement in each direction during the vibration. Therefore, the excitation force induced by the electromagnet should be estimated in advance to ensure the suitable design of the bowl feeder. In this study, a theoretical solution was developed to calculate the electro-magnetic force of the electromagnet for a bowl feeder. Using the proposed solution, the electro-magnetic forces corresponding to a variation in the input parameters of the electromagnet, such as the voltage, frequency, and air gap, could be obtained. The force values obtained using the theoretical solution exhibited a satisfactory agreement with the results obtained using the finite element method, thereby demonstrating the validity of the approach. Subsequently, the bowl displacements were analyzed using the motion equation for the bowl feeder when the theoretically obtained excitation force were applied to vibrate the feeder. The correlation between the vertical displacements of the bowl and input parameters of the electromagnet could be obtained.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.3
• /
• pp.353-358
• /
• 2010

This research introduces a new and improved design for a pneumatic cylinder driven roll feeder wherein each of the principal rotating feeder parts is configured so as to have feeding accuracy and to be low manufacturing cost. The feed pitch accuracy of the proposed roll feeder was evaluated by measuring lengths of cut offs of the strip stock with a shear attached to an air press. The air press was designed, manufactured, and mounted on the same table of the proposed roll feeder such that the strip stock maintained horizontal plane until the strip stock entered into the shear. The proposed roll feeder and the air press were designed to be operated automatically by a PLC employed controller. The feed pitch accuracy of the proposed roll feeder was analyzed by setting the pitch as 10, 12.5, and 15mm. At each predetermined feed pitch, the proposed roll feeder was tested 300 times as one test set and replicated three times. The average lengths of the cut offs of the strip stock ranged from 9.98 to 10.13mm, from 12.42 to 12.57mm, and from 14.96 to 15.06mm at the predetermined 10, 12.5, and 15mm feed pitch, respectively, among the total of 900 samples of each feed pitch. Main cause of variation of the length of the cut off of the strip stock fed by the proposed roll feeder was considered to be fluctuation of the air press during recompressing period of the air compressor to pressurize the air in the air tank. The largest difference between the maximum and the minimum length of the cut off was appeared while the air compressor recompressing the air. The air compressor used for this study restricted the air delivered to the proposed roll feeder while it was still running. Thus, this air delivery restriction problem should be improved by stabilizing the air press while the proposed roll feeder is running.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.5 s.108
• /
• pp.476-482
• /
• 2006

In this paper, a multimode feed horn antenna is suggested for a high power microwave(HPM) antenna system. The proposed HPM feed horn antenna which is connected with a mode converter is located between source and reflector antenna. A multimode feed horn antenna which has reduced -25 dB beamwidth is designed and fabricated for miniaturization of reflector antenna because -25 dB beamwidth which is determined by considering spillover of feed horn antenna decides a size of reflector in case of HPM. As a result, feed system which uses the multimode feed horn antenna has high gain about 27 dBi and return loss is less than -22 dB at 10 GHz. The measured -25 dB beamwidths of the radiation pattern at vertical, horizontal-plane equal to $20.24^{\circ},\;28.92^{\circ}$ which is less than about $10^{\circ}$ beamwidth of conventional feed system. Thus the suggested feed hem antenna is suitable to feed horn for miniaturization of HPM antenna system.