• Journal of Welding and Joining
• /
• v.15 no.2
• /
• pp.81-88
• /
• 1997

The residual stresses produced by a circumferential weld between axisymmetric cylinders are one of the most important problems concerning buckling strength, fatigue strength, stress corrosion cracking in shell structures, and arc quite different from those due to a butt weld between flat plates. This paper presents experimental studies on weld cylinder models of various heat inputs and thin cylinder diameters by blind hole drilling method. As a result, it is certified that weld residual stress (axial stress and hoop stress) is larger, as heat input and shell cylinder diameter are larger, and that experimental results show good agreement with the result of preceding researchers.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.79-82
• /
• 2008

In this paper, results of simulational round robin test on residual stress prediction was provided. Welding residual stress is one of the reasons for primary water stress corrosion cracking in PWR. Therefore, quantifying the welding variables and defining the recommendation for prediction welding residual stress is important. Through the round robin test, it is known that compressive axial and hoop residual stress occurs in dissimilar metal weld and pre-existing residual stress distribution in dissimilar metal weld was affected by similar metal weld due to short length of safe end.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.1309-1310
• /
• 2011

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.1
• /
• pp.72-81
• /
• 2009

This paper provides simulational round robin test results for welding residual stress prediction of safety/relief nozzle. To quantify the welding variables and define the recommendation for prediction and determination of welding residual stress, 6 partners in 5 institutes participated in round robin test. It is concluded that compressive axial and hoop residual stress occurs in dissimilar metal weld and pre-existing residual stress distribution in dissimilar metal weld was affected by similar metal weld due to short length of safe end. Although the reason for the deviation among the results was not pursued further, the effect of several key elements of FE analyses on welding residual stress was investigated in this paper.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.98-103
• /
• 2008

This paper is to discuss distribution of welding residual stresses of a ferritic low alloy steel nozzle with dissimilar metal weld using Alloy 82/182. Two dimensional (2D) thermo-mechanical finite element analyses are carried out to simulate multi-pass welding process on the basis of the detailed and fabrication data. On performing the welding analysis generally, the characteristics on the heat input and heat transfer of weld are affected on the weld residual stress analyses. Thermal analyses in the welding heat cycle process is very important process in weld residual stress analyses. Therefore, heat is rapidly input to the weld pass material, using internal volumetric heat generation, at a rate which raises the peak weld metal temperature to $2200^{\circ}C$ and the base metal adjacent to the weld to about $1400^{\circ}C$. These are approximately the temperature that the weld metal and surrounding base materials reach during welding. Also, According to the various ways of appling the weld heat source, the predicted residual stress results are compared with measured axial, hoop and radial through-wall profiles in the heat affected zone of test component. Also, those results are compared with those of full 3-dimensional simulation.

• Journal of the Society of Disaster Information
• /
• v.11 no.1
• /
• pp.1-8
• /
• 2015

This paper presents finite element (FE) analyses to clarify the effects of external pressure on the residual stresses in a girth-welded steel pipe. At first, FE simulation of the girth welding process is carried out to obtain the weld-induced residual stresses employing sequentially coupled three-dimensional (3-D) thermo-mechanical FE formulation. Then, 3-D elastic-plastic FE analyses incorporating the residual stresses and plastic strains obtained from the preceding FE simulation are performed to investigate the residual stress behavior in the girth-welded pipe under external pressure. The FE analysis results show that the hoop compressive stresses induced by the external pressure significantly alter the hoop residual stresses in the course of the mechanical loading.

• Journal of the Korean Society of Safety
• /
• v.24 no.2
• /
• pp.17-22
• /
• 2009

Thermal stress and elastic creeping stress analysis was conducted by finite element method to simulate start-up process of a boiler header of 500MW standard fossil power plant. Start-up temperature and operating pressure history were simplified from the real field data and they were used for the thermal stress analysis. Two kinds of thermal stress analysis were considered. In the first case only temperature increase was considered and in the second case both of temperature and operating pressure histories were considered. In the first analysis peak stress was occurred during the temperature increase from the room temperature. Hence cracking or fracture may occur at the temperature far below the operating maximum temperature. In the results of the second analysis von Mises stress appeared to be higher after the second temperature increase. This is due to internal pressure increase not due to the thermal stress. When the stress components of radial(r), hoop($\theta$) and longitudinal(z) stress were investigated, compression hoop stress was occurred at inner surface of the stub tube when the temperature increased from room temperature to elevated temperature. Then it was changed to tension hoop stress and increased because of the operating pressure. It was expected that frequent start-up and shut-down operations could cause thermal fatigue damage and cracking at the stub tube hole in the header. Elastic-creeping analysis was also carried out to investigate the stress relaxation due to creep and stabilized stress after considerable elapsed time. The results could be used for assessing the creep damage and the residual life of the boiler header during the long-tenn service.

• Transactions of Materials Processing
• /
• v.14 no.8 s.80
• /
• pp.704-711
• /
• 2005

The influence of process parameters in drawn wire on residual stresses was investigated. Based on a FE-simulation of the wire drawing process, the effects of process parameters such as semi-die angle, reduction, friction coefficient and bearing length on the residual stresses were investigated. The validity of the FE-simulation results was verified by the comparison of the previous simulated results with experimental data. In this study, semi-die angle and die reduction have significant effect on the residual stresses at the surface of drawn wire. Several methods such as, addition of axial tension, application of skin pass, straightening in multi-roll straightener etc, were suggested in the previous studies to reduce the residual stresses. In this study, the results show that the concurrent application of skin pass with low die reduction and low semi-die angle at the final stage of drawing operation reduces dramatically the both axial and hoop residual stresses after drawing

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.834-837
• /
• 2005

This study presents a study on the influence of process parameters(semi-die angle, die reduction, friction condition, and bearing length) in drawn wire on residual stresses were investigated using FE-analysis. In this study, semi-die angle and die reduction have a significant effect on the residual stresses at the surface of drawn wire. In the previous study, in order to reduce the residual stresses, several methods were suggested: addition of axial tension, application of skin pass, straightening in multi-roll straightener etc. In this study, it can be known that the concurrent application of skin pass with low die reduction and low semi-die angle at the final stage of drawing operation reduces dramatically the both axial and hoop residual stresses after drawing.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.6 no.2
• /
• pp.34-41
• /
• 2010

This work is concerned with the analysis of stress corrosion cracking(SCC) behavior of Alloy 600 nozzle penetration mock-up according to a residual stress induced by a dissimilar metal welding(DMW) in a nuclear reactor pressure vessel. The effects of the dimension and materials of the nozzle penetration on the deformation and the residual stress induced by DMW were investigated using a finite element analysis(FEA). The inner diameter(ID) change of the nozzle by DMW and its dependance on the design variables, calculated by FEA, were well consistent with those measured from the mock-up. Accelerated SCC tests were performed for three mock-ups with different wall thicknesses in a highly acidic solution to investigate mainly the effect of the residual stress on the SCC behavior of Alloy 600 nozzle. From a destructive examination of the mock-up after the tests, the SCC behavior of the nozzle was fairly related with the residual stress induced by DMW : axial cracks were found in the ID surface of the nozzle within the J-weld region where the highest tensile hoop stress was predicted by FEA, while circumferential cracks were observed beyond both J-weld root and toe where the highest tensile axial stress was expected.