• 열처리공학회지
• /
• 제6권3호
• /
• pp.127-137
• /
• 1993

The changes of lamellar(${\alpha}_2+{\gamma}$) structure of TiAl intermetallic compound which is a high potential, high temperature aerospace material was investigated by heat treatment. The lamellar structure was short and made subgrain in prior a grains after homogenizing at 1523 K. It became longer and finer, and the subgrain went out during subsequent isothermal heatteating at 1273 K. The yield, fracture strength and strain to fracture if the heat treated specimens was increased and the hardness of them was decreased a little in the finer lamellar structure, because fine lamellar interface, sugrain boundary and grain boundary may block initiation and propagation of crack.

• 한국식품과학회지
• /
• 제32권4호
• /
• pp.902-907
• /
• 2000

폐기되는 연어 정자로부터 프로타민을 제조하여 프로타민이 가지는 항균성 및 항산화성을 시험하였다. 그 결과 제조시 전처리 방법에 따라 추출 수율이 차이가 있었는데, 초음파와 균질기 전처리에 의한 추출 방법은 수율에 큰 차이를 보이지 않았지만, $80^{\circ}C$로 가열되는 마이크로파 전처리는 다른 전처리 시료에 비해 5%이상 수율이 낮았다. 각 조건별로 제조된 프로타민 시료들의 아미노산 분석 결과, 시판 프로타민의 경우 arginine 함량이 전체 61.1% 정도를 차지하였고, proline 함량은 11% 정도였다. $H_{2}SO_{4}$ 용액으로 균질화하여 추출한 M의 경우 arginine 함량이 19.3% 정도였고, 반면 methionine과 proline이 각각 34.3%, 28.1% 정도를 차지하였으며, 균질화시킨 다음 $H_{2}SO_{4}$ 용액으로 추출한 MC도 시판 프로타민과 유사한 조성을 나타내었다. 마이크로파 전처리 P60 및 초음파 전처리 UU6는 arginine이 각각 60.8%, 52.4%를 차지하였고, P60은 proline 함량이, UU6는 tryptophan 함량이 다소 많은 것이 차이였다. 제조된 프로타민은 곰팡이 이외에 그람양성 및 음성 세균에 대해 항균활성이 있었고, UU6나 P60이 다른 시료에 비해 활성이 높았고, 일부 세균에 대해서는 농도 의존성이 있으며, 시판 제품보다 높은 항균활성을 나타내었다. 프로타민의 항산화성은 전처리 방법에 관계없이 모든 시료에서 확인되었으며, 전처리 방법에 따라 어느정도 차이를 보였다. $EDA_{50}$을 측정한 결과, P60이 $101\;{\mu}g/mL$, UU6가 $410\;{\mu}g/mL$, M이 $520\;{\mu}g/mL$, MC가 $490\;{\mu}g/mL$였으며, 시판 프로타민은 $470\;{\mu}g/mL$였다.

• 한국식품과학회지
• /
• 제24권5호
• /
• pp.408-413
• /
• 1992

신속간편법으로서 식품의 성분함량 측정에 이용되는 근적외 반사분광분석에서 문제가 되고 있는 시료의 균질도의 차이가 흡광도에 미치는 영향을 조사하고 흡광도로 나타난 수치를 수학적으로 처리함으로써 예측의 오차는 다음과 같이 감소하였다. 1. 세절도가 일정한 시료의 흡광도를 무변형, 1차 미분 및 2차 미분하여 calibration한 후 세절도가 다양한 시료의 성분을 예측한 결과 예측오차(standard error of prediction)는 수분함량에 있어서 1.478%, 0.658% 및 0.580%, 지방함량의 예측오차 0.949%, 0.637%, 및 0.527%이었으며 단백질 측정시 각각 0.514%, 0.493% 및 0.394%로 2차 미분의 예측오차가 모든 성분측정에서 가장 낮음을 알 수 있었다. 2. 세절도가 다양한 시료의 무변형, 1차 미분 및 2차 미분처리한 calibration을 이용하여 세절도가 다양한 시료의 성분을 예측한 결과 수분함량 예측오차는 각각 1.026%, 0.589% 및 0.568%, 지방함량 예측오차는 각각 0.828%, 0.639% 및 0.602% 이었으며 단백질함량 예측오차는 0.860%, 0.557% 및 0.399%로서 역시 2차 미분, 1차 미분, 무변형의 순으로 정확성이 높았다. 결과를 종합할 때 흡광도를 수학적으로 처리하여 calibration에 이용하므로서 calibration시료의 세절도에 관계없이 측정결과의 정확성은 높아졌다.

• 한국식품영양과학회지
• /
• 제27권6호
• /
• pp.1204-1210
• /
• 1998

This study was focused on the purification, characterization and promotion mode of an anticoagulant polysaccharide from Hizikia fusiforme. The anticoagulant crude polysaccharide(HF 0) was obtained by using hot water extraction at 100oC for 3 hrs after homogenizing desalted Hizikia fusiforme. The anticoagulant polysaccharide(HF 2 3 1a) was purified from the crude extract(HF 0) through stepwise gradient ethanol precipitation(HF 2), DEAE Toyopearl 650C(HF 2 3), Sephadex G 75(HF 2 3 1), Sepharose CL 6B(HF 2 3 1a) chromatography and HPLC to homogeneity. HF 2 3 1a was estimated at 5.3$\times$105 Da molecular weight and composed of fucose(51.92%), galactose(19.34%), mannose(13.92%), xylose (7.14%), arabinose(3.95%) and rhamnose(3.78%), and comprimised 29.7 % sulfate residue. The sulfated anticoagulant polysaccharide from HF 2 3 1a was proposed to inhibit via the intrinsic pathway and common pathway in the blood coagulation. The HF 2 3 1a exhibited the anticoagulant activity by activating an antithrombin III and the activity depended on the concentration of HF 2 3 1a. Acute toxicity of HF 2 in mice was not detected. Only 14 of 33 control mice(11.4%) that had taken saline survived for 30 min after injecting thrombin(100 NIH unit/ml).

• Steel and Composite Structures
• /
• 제36권2호
• /
• pp.229-247
• /
• 2020

This study analyzed stresses in concrete and its reinforcement, computing the additional loading transferred by concrete creep. The loading varied from zero, structure exclusively under its self-weight, up to the critical buckling load. The studied structure was a real, tapered, reinforced concrete pole. As concrete is a composite material, homogenizing techniques were used in the calculations. Due to the static indetermination for determining the normal forces acting on concrete and reinforcement, equations that considered the balance of forces and compatibility of displacement on cross-sections were employed. In the mathematical solution used to define the critical buckling load, all the elements of the structural dynamics present in the system were considered, including the column self-weight. The structural imperfections were linearized using the geometric stiffness, the proprieties of the concrete were considered according to the guidelines of the American Concrete Institute (ACI 209R), and the ground was modeled as a set of distributed springs along the foundation length. Critical buckling loads were computed at different time intervals after the structure was loaded. Finite element method results were also obtained for comparison. For an interval of 5000 days, the modulus of elasticity and critical buckling load reduced by 36% and 27%, respectively, compared to an interval of zero days. During this time interval, stress on the reinforcement steel reached within 5% of the steel yield strength. The computed strains in that interval stayed below the normative limit.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년도 춘계 학술대회 개요집
• /
• pp.266-268
• /
• 2006

The effects of the brazing temperature and homogenizing time for brazed specimens on the joint of Ni-based superalloys such as Haynes 250, Inconel 617 and Hastelloy-X were investigated. The brazing alloy is nickel base MBF 15. The foil had a thickness of $38{\mu}m$, which was used two sheets of that for the all experiments. The experimental brazing was carried out by a brazing process in a vacuum of approximately $2{\times}10^{-5}$ Torr, an applied pressure of about 0.74MPa and the three kinds of brazing temperatures were 1100, 1150, and $1190^{\circ}C$ for a holding time of 5 to 1440 minutes. Microstructural observations were made on the cross-sectional samples by using an optical microscope(OM), scanning electron microscope(SEM), and electron probe X-ray microanalyzer(EPMA). The tensile tests were performed at room temperature with a cross head speed 1.5 mm/min according to ASTM E8M. The results show that excellent joint tensile strengths of as high as 788MPa were obtained when processed at $1190^{\circ}C$ for 5 minutes.

• 열처리공학회지
• /
• 제12권2호
• /
• pp.129-135
• /
• 1999

The effects of Ag addition on the microstructures and mechanical properties of 7050 Al alloy were investigated. Various homogenizing and aging treatments were carried out to analyze the controversial effects of Ag in 7050 Al alloy. Transmission electron microscopy(TEM) was used for microstructural analysis. The hardening precipitates(${\eta}^{\prime}$) become finer with Ag addition. It suggests that Ag promotes easier nucleation of ${\eta}{\prime}$. The strength of overaged Ag bearing alloys are higher than that of Ag free alloy. Hardening precipitates(${\eta}^{\prime}$) in Ag bearing alloys are smaller than that of Ag free alloys, because the growth rate of ${\eta}^{\prime}$ during overaging stage is lower in Ag bearing alloys.

• 한국항공우주학회지
• /
• 제33권8호
• /
• pp.1-7
• /
• 2005

본 연구에서는 삼각격자 균질화를 위하여, 확장된 위상학적 개선과정과 국소 최적화 기반 평활화를 결합한 국소 개선기법을 제안하였다. 먼저 격자의 연결 구조를 확장된 위상학적 개선과정을 적용하여 최적의 연결구조로 개선한다. 다음으로 격자의 질을 나타내는 비틀림척도를 최대화하기 위해 국소 최적화 기반 평활화를 수행한다. 이 국소 개선기법을 이용하여, 두 가지 격자 예제에 대하여 삼각격자 균질화를 수행하였다. 이 예들을 통하여, 본 연구에서 제안한 국소 개선알고리듬이 삼각격자의 질을 크게 향상시켜주는 경제적이며 효과적인 방법임을 보여준다. 또한, 이 기법은 적응격자 세분화의 격자 재생성과정에도 용이하게 적용될 수 있다.

• Journal of Pharmaceutical Investigation
• /
• 제17권1호
• /
• pp.38-40
• /
• 1987

To optimize the preparation condition of oil in water microemulsion rheological method was used. The viscosity-temperature curve of refined soybean oil was recorded and from this result microemulsion was prepared at various temperatures and evaluated by Coulter counter during 3 weeks. The difference in rheograms of crude emulsion and the microemulsion varying the number of passes in the homogenizer was also examined. From above experiments following conclusions were obtained. 1) Through all the process, temperature was an important factor and the optimum was $60-80^{\circ}C$. 2) By first pass in the homogenizer, most oil droplets were finely dispersed. 3) In the homogenizing step the higher pressure results in the finer dispersion but as the pressure goes up, the differential efficiency of dispersion was decreased.

• 한국주조공학회지
• /
• 제19권1호
• /
• pp.33-37
• /
• 1999

White cast iron of 3%C-10%Cr-5%Mo-5%W was casted, and then heat treated with three different methods such as homogenizing, austenitizing and tempering to observe its effects on the microstructure, hardness and abrasive wear resistance. In uni-directional soldification, bamboo tree-like $M_7C_3$ carbide grew along with the heat flow direction, and fishbone-like $M_6C$ carbide was dispersed randomly among $M_7C_3$ carbides. While almost pearlitic structures were observed in the as-cast specimen, those of the heat treated specimens consisted of secondary carbide, retained austenite and tempered martensite. In austenitized specimen, the amounts of retained austenite were 60.88% due to the higher cooling rate encountered in forced air cooling. On the other hand, the amounts of retained austenite were reduced from 60.88% to 23.85% in tempered specimen due to the transformation of austenite into tempered martensite. The hardness of tempered specimen showed the highest value, and then decreased in the order of austenitized, as-cast and homogenized specimens. But, the abrasive wear resistance of austenitized specimen was the highest, and then decreased in the order of tempered, as-cast and homogenized specimens.