• Geomechanics and Engineering
• /
• 제38권3호
• /
• pp.261-273
• /
• 2024

This study presents a groundbreaking analytical approach to find an exact solution for the bearing capacity of strip footings on reinforced slopes, utilizing the two-phase approach and slip line method. The two-phase approach is considered as a generalized homogenization technique. The slip line method is leveraged to derive the stress field as a lower bound solution and the velocity field as an upper bound solution, thereby facilitating the attainment of an exact solution. The key finding points out the variation of the bearing capacity factor N_γ with influencing factors including the backfill soil friction angle, the footing setback distance from the slope crest edge, slope angle, strength, and volumetric fraction of inclusion layers. The results are evaluated by comparing them with those of relevant studies in the literature considering analytical and experimental studies. Through the application of the two-phase approach, it becomes feasible to determine the tensile loads mobilized along the inclusion layers associated with the failure zone. It is attempted to demonstrate the results by utilizing non-dimensional graphs to clearly illustrate variable impacts on reinforced soil stability. This research contributes significantly to advancing geotechnical engineering practices, specifically in the realm of static design considerations for reinforced soil structures.

• Steel and Composite Structures
• /
• 제42권5호
• /
• pp.699-710
• /
• 2022

This work presents a comprehensive study on the surface energy effect on the axial frequency analyses of AFGM nanorods in cylindrical coordinates. The AFGM nanorods are considered to be thin, relatively thick, and thick. In thin nanorods, effects of the inertia of lateral motions and the shear stiffness are ignored; in relatively thick nanorods, only the first one is considered; and in thick nanorods, both of them are considered in the kinetic energy and the strain energy of the nanorod, respectively. The surface elasticity theory which includes three surface parameters called surface density, surface stress, and surface Lame constants, is implemented to consider the size effect. The power-law form is considered for variation of the material properties through the axial direction. Hamilton's principle is used to derive the governing equations and boundary conditions. Due to considering the surface stress, the governing equation and boundary condition become inhomogeneous. After homogenization of them using an appropriate change of variable, axial natural frequencies are calculated implementing harmonic differential quadrature (HDQ) method. Comprehensive results including effects of geometric parameters and various material properties are presented for a wide range of boundary condition types. It is believed that this study is a comprehensive one that can help posterities for design and manufacturing of nano-electro-mechanical systems.

• 한국생산제조학회지
• /
• 제20권4호
• /
• pp.412-418
• /
• 2011

Reliability-based Topology optimization(RBTO) is to get an optimal design satisfying uncertainties of design variables. Although RBTO based on homogenization and density distribution method has been done, RBTO based on BESO has not been reported yet. This study presents a reliability-based topology optimization(RBTO) using bi-directional evolutionary structural optimization(BESO). Topology optimization is formulated as volume minimization problem with probabilistic displacement constraint. Young's modulus, external load and thickness are considered as uncertain variables. In order to compute reliability index, four methods, i.e., RIA, PMA, SLSV and ADL(adaptive-loop), are used. Reliability-based topology optimization design process is conducted to obtain optimal topology satisfying allowable displacement and target reliability index with the above four methods, and then each result is compared with respect to numerical stability and computing time. The results of this study show that the RBTO based on BESO using the four methods can effectively be applied for topology optimization. And it was confirmed that DLSV and ADL had better numerical efficiency than SLSV. ADL and SLSV had better time cost than DLSV. Consequently, ADL method showed the best time efficiency and good numerical stability.

• 한국전산유체공학회지
• /
• 제17권4호
• /
• pp.41-48
• /
• 2012

A numerical analysis of thermal stratification in the upper plenum of the MONJU fast breeder reactor was performed. Calculations were performed for a 1/6 simplified model of the MONJU reactor using the commercial code, CFX-13. To better resolve the geometrically complex upper core structure of the MONJU reactor, the porous media approach was adopted for the simulation. First, a steady state solution was obtained and the transient solutions were then obtained for the turbine trip test conducted in December 1995. The time dependent inlet conditions for the mass flow rate and temperature were provided by JAEA. Good agreement with the experimental data was observed for steady state solution. The numerical solution of the transient analysis shows the formation of thermal stratification within the upper plenum of the reactor vessel during the turbine trip test. The temporal variations of temperature were predicted accurately by the present method in the initial rapid coastdown period (~300 seconds). However, transient numerical solutions show a faster thermal mixing than that observed in the experiment after the initial coastdown period. A nearly homogenization of the temperature field in the upper plenum is predicted after about 900 seconds, which is a much shorter-term thermal stratification than the experimental data indicates. This discrepancy is due to the shortcoming of the turbulence models available in the CFX-13 code for a natural convection flow with thermal stratification.

• Structural Engineering and Mechanics
• /
• 제69권2호
• /
• pp.155-162
• /
• 2019

It is very common to find an empirical formulation in an earthquake design code to calculate fundamental vibration period of a structural system. Fundamental vibration period or frequency is a key parameter to provide adequate information pertinent to dynamic characteristics and performance assessment of a structure. This parameter enables to assess seismic demand of a structure. It is possible to find an empirical formulation related to reinforced concrete structures, masonry towers and slender masonry structures. Calculated natural vibration frequencies suggested by empirical formulation in the literatures has not suits in a high accuracy to the case of rest of the historical masonry bridges due to different construction techniques and wide variety of material properties. For the listed reasons, estimation of fundamental frequency gets harder. This paper aims to present an empirical formulation through Mean Square Error study to find ambient vibration frequency of historical masonry bridges by using a non-linear regression model. For this purpose, a series of data collected from literature especially focused on the finite element models of historical masonry bridges modelled in a full scale to get first global natural frequency, unit weight and elasticity modulus of used dominant material based on homogenization approach, length, height and width of the masonry bridge and main span length were considered to predict natural vibration frequency. An empirical formulation is proposed with 81% accuracy. Also, this study draw attention that this accuracy decreases to 35%, if the modulus of elasticity and unit weight are ignored.

• 한국전산구조공학회논문집
• /
• 제14권4호
• /
• pp.495-503
• /
• 2001

기능 경사 복합재에서는 열적 탄성 거동이 성분의 구성분포에 의해 명백하게 구분되어지도록 두가지의 성분입자들을 특정한 체적분율 분포에 따라서 혼합한다. 따라서, 설계자는 주어진 제약조건에 대해 목적하는 성능에 적합한 기능 경사 복합재를 설계하기 위해서 최적의 체적분율 분포를 결정해야만 한다. 본 연구에서는 금속과 세라믹으로 구성된 내열 기능 경사 복합재의 2차원 체적분율을 최적화하기 위하여 내부벌칙함수법과 유한차분법을 사용한 수치 최적화기법을 제안하였다. 최적화 효율을 위해 단일 설계변수의 유한개의 균질 사각형 격자로 기능 경사 복합재의 영역을 나누었다. 그렇지만, 연속적인 체적분율을 구현하기 위하여 최적설계 후에 전체적으로 연속적인 이차원 선형함수로써 불연속적인 체적분율을 보간하였다.

• 한국음향학회지
• /
• 제30권7호
• /
• pp.368-376
• /
• 2011

압전복합체는 낮은 음향 임피던스와 높은 전기-기계 결합계수를 가지는 장점으로 인해 광대역 음향 트랜스듀서의 개발에 널리 활용되고 있으나, 구조의 복잡성으로 인해 이를 이용한 각종 트랜스듀서의 설계에 많은 제약이 있어왔다. 본 논문에서는 1-3형 압전복합체의 등가물성을 도출하여, 압전복합체와 동일한 특성을 가지는 균질한 단일 상의 물질로 대체하는 방법을 제안하였다. 압전복합체의 다양한 진동모드에서의 공진특성을 정확히 나타낼 수 있는 등가물성 도출을 위해 공진법과 유한 요소 해석법을 이용하였다. 제작한 1-3형 압전복합체 시편과 유한요소해석 모델의 주파수 특성을 비교하여 본 논문의 등가물성도출 방법의 타당성을 검증하였으며, 등가물성을 각 공진 모드별 단일상의 유한요소 해석 모델들에 적용하여 도출한 물성값의 정확성을 분석하였다.

• Composites Research
• /
• 제35권3호
• /
• pp.188-195
• /
• 2022

본 논문은 멀티스케일 공정-구조 해석의 방법론을 제안하고 단섬유층과 직물층으로 이루어진 배터리 하우징 파트에 적용한다. 특별히 마이크로스케일 대표체적요소(RVE: Representative Volume Element)안 기지의 불확정성을 고려하였다. 마이크로스케일의 RVE내 기지 물성의 랜덤한 공간내 분포는 KLE(Karhunen-Loeve Expansion)을 통해 구현하였다. 공간상 랜덤분포된 기지 물성을 갖는 RVE의 유효 물성을 전산균질화를 통해 얻어 매크로스케일 유한요소 모델에 매핑하였다. 또한 하이브리드 공정해석을 통해 압축 성형 해석으로부터 얻은 잔류응력과 섬유배향을 매핑한 유한요소 모델과 드레이핑 공정 해석결과로부터 얻어진 섬유배향을 매핑한 모델을 결합하였다. 본 연구에 제안된 방법은 배터리 하우징 뿐만 아니라 다양한 재료 구성을 갖는 복합재료의 공정-구조해석을 통해 설계요구도를 엄밀하게 평가할 수 있을 것이라 기대된다.