• Journal of Korea Foundry Society
• /
• v.30 no.6
• /
• pp.235-240
• /
• 2010

The evolution of microstructure and phases of Mg-10Al-Mn alloy by cooling plate method during homogenization treatment have been investigated with metallographic analysis, scanning electron microscopy and energy dispersive spectroscopy. The ingots used for this experiment were prepared by cooling plate and homogenization heat treatment was performed at 300 and $400^{\circ}C$ for various holding times (0, 1, 4, 8 and 12h). The casting ingots were consisted of the fine grains and eutectic phases. And, these eutectic phases were dissolved into the matrix during homogenization treatment at $400^{\circ}C$ but the lower temperature (at $300^{\circ}C$) did not be.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.2
• /
• pp.153-161
• /
• 2009

Three-dimensional finite-element methods(FEM) have been used to analyze the thermal stress of an exhaust gas recirculation(EGR) cooler due to thermal and pressure load. Since efficiency and capability of the heat exchanger are mainly dependent on net heat transferring area of the EGR cooler system, the tube inside the system has a numerous dimples on the surface. Thus for finite element analysis, firstly the dimple-typed tube is modeled as a plain element without the dimple, and then the equivalent thermal conductivities and elastic modulus are calculated. This work describes the numerical homogenization procedure of the dimple-typed tube and verifies the equivalent material properties by comparison of a single unit and the actual full model. Finally, the homogenization scheme presented in this study can be efficiently applied to finite element analyses for the thermal stress and deformation behavior of the EGR cooler system with the dimple-typed tube.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.752-759
• /
• 2006

Conglomerates and core-stones are the typical composite geomaterials that are composed of a weak matrix and a strong pebble part. In general, we couldn't analyze the composite geomaterials by using emperical rock classification methods. In the study, a series of analyses of elastic behavior of composite geomaterials are carried out by using homogenization theory. 45-case models are made with considering 3 kind of factors such as gravel content, size and strength of matrix. Those are applicable to various composite geomaterials of conglomerates and core-stones. The size of analysis model is large enough to exceed REV.

• Journal of Powder Materials
• /
• v.2 no.1
• /
• pp.53-62
• /
• 1995

TLP(Transient-Liquid-Phase) bonding of Fe-base MA956 ODS alloy was performed. As insert metal a commercially available Ni-base alloy(MBF50) and an MA956 alloy with additive elements of 7wt% Si and 1wt% B were used. To confirm the idea that a concurrent use of MA956 powder with Insert metals can enhance the homogenization of constituent elements and thereby reduce the thickness of joint interface, MA956 powder was also inserted In a form of sheet. SEM observation and EDS analysis revealed that Cr-rich phase was formed in the bonded interface in initial stage of isothermal solidification during the bonding process, irrespective of kind of insert metals. Measurement of hardeness in the region of bonded interface and EDS analysis showed that a complete homogenization of composition could not be obtained especially in case of MBF50. Joints using either BSi insert metals only or BSi insert together with MA956 powder interlayer showed, however, a remarkable improvement in a compositional homogenization, even though a rapid grain growth in the bonded interface could not be hindered.

• Geomechanics and Engineering
• /
• v.16 no.3
• /
• pp.257-271
• /
• 2018

In this paper, the effect of the homogenization models on buckling and free vibration is presented for simply supported functionally graded plates (FGM) resting on elastic foundation. The majority of investigations developed in the last decade, explored the Voigt homogenization model to predict the effective proprieties of functionally graded materials at the macroscopic-scale for FGM mechanical behavior. For this reason, various models have been used to derive the effective proprieties of FGMs and simulate thereby their effects on the buckling and free vibration of FGM plates based on comparative studies that may differ in terms of several parameters. The refined plate theory, as used in this paper, is based on dividing the transverse displacement into both bending and shear components. This leads to a reduction in the number of unknowns and governing equations. Furthermore the present formulation utilizes a sinusoidal variation of displacement field across the thickness, and satisfies the stress-free boundary conditions on the upper and lower surfaces of the plate without requiring any shear correction factor. Equations of motion are derived from Hamilton's principle. Analytical solutions for the buckling and free vibration analysis are obtained for simply supported plates. The obtained results are compared with those predicted by other plate theories. This study shows the sensitivity of the obtained results to different homogenization models and that the results generated may vary considerably from one theory to another. Comprehensive visualization of results is provided. The analysis is relevant to aerospace, nuclear, civil and other structures.

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2000.09a
• /
• pp.55-61
• /
• 2000

For proper sampling of a rock and preparation of specimens, the representative elementary volume (REV) should be determined in rock mechanical test and numerical analysis. Mechanical properties of a rock, in general, would be strongly affected by mineral composition. In this reason REV of Youngju granite is determined by using stereoscopic microscope observation and homogenization numerical analysis. As the area of analysis model exceeds approximately 702 $ extrm{mm}^2$(900 elements), the change of the mineral composition is not observed. The calculated results indicate that Young's modulus is fluctuated with increase of the number of elements in homogenization numerical analysis mesh. However, as the number of elements exceeds 1156 (area of about 900 $ extrm{mm}^2$), Young's modulus does not change apparently.

• Tunnel and Underground Space
• /
• v.10 no.3
• /
• pp.309-315
• /
• 2000

For proper sampling of a rock and preparation of specimens, the representative elementary volume (REV) should be determined in rock mechanical test and numerical analysis. Mechanical properties of a rock, in general, would be strongly affected by mineral composition. In this reason REV of Youngju granite is determined by using stereoscopic microscope observation and homogenization numerical analysis. As the area of analysis model exceeds approximately 702$\textrm{mm}^2$(900 elements), the change of the mineral composition is not observed. The calculated results indicate that Young's modulus is fluctuated with increase of the number of elements in homogenization numerical analysis mesh. However, as the number of elements exceeds 1156 (area of about 900$\textrm{mm}^2$), Young's modulus does not change apparently.

• Advances in concrete construction
• /
• v.5 no.3
• /
• pp.221-240
• /
• 2017

The modeling of the mechanical behavior of quasi-brittle materials is still a challenge task, mainly in failure processes when fracture and plasticity phenomena become important actors in dissipative processes which occur in materials like concrete, as instance. Many homogenization-based approaches have been proposed to deal with heterogeneous materials in the last years. In this context, a computational homogenization modeling for concrete is presented in this work using the concept of Representative Volume Element (RVE). The material is considered as a three-phase material consisting of interface zone (ITZ), matrix and inclusions-each constituent modeled by an independent constitutive model. The Representative Volume Element (RVE) consists of inclusions idealized as circular shapes symmetrically and nonsymmetrically placed into the specimen. The interface zone is modeled by means of cohesive contact finite elements. The inclusion is modeled as linear elastic and matrix region is considered as elastoplastic material. A set of examples is presented in order to show the potentialities and limitations of the proposed modeling. The consideration of the fracture processes in the ITZ is fundamental to capture complex macroscopic characteristics of the material using simple constitutive models at mesoscopic level.

• Asian-Australasian Journal of Animal Sciences
• /
• v.16 no.3
• /
• pp.409-416
• /
• 2003

This study was carried out to find a cholesterol removal rate, flavor development and bitter amino acid productions in Cheddar cheese treated with $\beta$-cyclodextrin (CD): 1) Control (no homogenization, no $\beta$-CD), and 2) Milk treatment (1000 psi milk homogenization, 1% $\beta$-CD). The cholesterol removal of the cheese was 79.3%. The production of short-chain free fatty acids (FFA) increased with a ripening time in both control and milk treated cheese. The releasing quantity of short-chain FFA was higher in milk treated cheese than control at 5 and 7 mo ripening. Not much difference was found in neutral volatile compound production between samples. In bitter-tasted amino acids, milk treatment group produced much higher than control. In sensory analysis, texture score of control Cheddar cheese significantly increased with ripening time, however, that in cholesterol-reduced cheese decreased dramatically. Our results indicated that the cheese made by $\beta$-CD treated milk with low pressure homogenization showed an effective cholesterol reduction and a rapid cheese ripening, while no capture of flavor compounds by $\beta$-CD.

• Composites Research
• /
• v.33 no.2
• /
• pp.81-89
• /
• 2020

In this review paper, we introduce recent research studied effective physical properties of the reinforced composite using mean-field homogenization. We address homogenization for effective stiffness and expand it to effective thermal/electrical conductivity and dielectric constant. Multiphysics problems like piezoelectricity and thermoelectricity are considered by simplifying the constitutive equation into the linear equations like Hooke's law. We present a generalized theoretical formula for predicting effective physical properties of composite and validation by against finite element analysis.