• Journal of Satellite, Information and Communications
• /
• v.9 no.1
• /
• pp.33-37
• /
• 2014

This paper introduces homogeneous liquid crystal (LC) orientations on chemically modulated polystyrene (PS) surfaces using various ion beam (IB) exposure time. Transparent PS was replaced with conventional polyimide material. As a non-contact process, IB bombardment process induced LC orientation in the direction parallel to the IB process. Through x-ray photoelectron spectroscopy, it was shown that the chemical compositional changes of the IB-irradiated PS surfaces were determined as a function of IB exposure time.Using this analysis, the optimal IB bombardment condition was determined at IB exposure time of up to 15 s. Moreover, thermal stability on IB-irradiated PS surfaces were carried out which showed that a relatively high IB exposure time induced a thermally stable LC alignment property.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.3
• /
• pp.305-310
• /
• 2004

We have studied the optimal phase retardation value of a homogeneously aligned liquid crystal (LC) driven by fringe-field when using the LC with positive dielectric anisotropy. In general, the transmittance of a homogeneous aligned LC cell under crossed polarizer is maximum when a twist angle of LC by in-plane rotation is 45$^{\circ}$ with polarizer and the cell retardation becomes λ/2. However, the device using the LC with positive dielectric anisotropy does not follow this since the degree of rotation of the LC is dependent on electrode position and in addition the LCs tilt up along the fringe-field. At the center of common and pixel electrode, the LC is most twisted around a middle position of a cell whereas at the edge position of pixel electrode, the LC is most twisted near bottom surface of a cell. Consequently, the optimal phase retardation of the device becomes much larger than λ/2 and the transmittance can be described using the combination of the in-plane switching and twisted nematic mode.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1533-1536
• /
• 2006

A novel single cell gap transflective liquid crystal display was developed. By using the ink jet printing technology, we fabricated a transflective liquid crystal display with the hybrid alignment in the reflective region and the homogeneous alignment in the transmission region. Compared with the traditional technologies, our technology provided the advantages of easy process, high yield, fast throughput, and less material usage. We also applied this technology to the 2.4 inch prototype. This panel could be implemented in the handheld product applications.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.06a
• /
• pp.5-15
• /
• 1997

It is the objective of this study that by conducting the serni-solid extrusion using A12024, the effect of various process variables on the quality of extruded product and extrusion force is understood. The results of experiment are compared with those of finite element simulation in order to verify the effectiveness of the developed FE-simulation code. In order to simulate densification in the deformation of serni-solid material, the semi-solid material is assumed to be composed of solid region as porous skeleton following compressible visco-plastic model and liquid region following Darcy's equation for the liquid flow saturated in the interstitial space. Then the flow and deformation of the semi-solid alloy are analyzed by coupling the deformation of the porous skeleton and the flow of the eutectic liquid. It is assumed that initial solid fraction is homogeneous. Yield and plastic potential function presented by Kuhn and constitutive model developed by Gunasekera are used for solid skeleton.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.629-632
• /
• 2009

We have proposed a novel viewing angle controllable display of in-plane switching (IPS) mode with single panel. One pixel of this device is divided to two regions, in which main pixel shows image and sub pixel for viewing angle control. In initial state, the liquid crystal of sub pixel is homogeneous aligned on substrate for wide viewing angle mode. On the other hand, after applying voltage, the liquid crystal of sub pixel tilts up for narrow viewing angle mode. The proposed device has advantage for the function for simple manufacturing process and good viewing angle control with single panel.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.189-192
• /
• 2005

We have investigated the EO characteristics generation of pretilt angle for a nematic liquid crystal (NLC) alignment with photoalignment method on three kinds of photopolymer surfaces using polymer substrates. The LC homogeneous alignment were observed on the PMI3CA (N-(phenyl)maleimide with 3-carbon chain cinnamoyl group) and PMIF (N-(phenyl)maleimide including fluoro cinnamoyl group). However, the homeotropic alignment on the PMI5CA(N-(phenyl)maleimide with 5-carbon chain cinnamoyl group) was obtained. Also, EO characteristics of the flexible photoaligned TN-LCD using PMIF surface are better than that of the flexible TN-LCD using PMI3CA surface. Also, the stable EO performances of flexible photoaligned VA-LCD using the PMI5CA surface was observed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.279-282
• /
• 2005

Composites comprising various volume fractions of crystalline nickel and bulk amorphous (BA) were produced by means of electroless coating of nickel on BA powder of $Cu_{54}Ni_6Zr_{22}Ti_{18}$ and subsequent spark plasma sintering (SPS) of coated BA powder. The flow curves of composites at various temperatures in the supercooled liquid region were determined by the uniaxial compression test with various strain rates. During compression at $450^{\circ}C$ with $\dot{\varepsilon}=2\times10^{-3}$, the monolithic BA sample and crystalline-BA composites displayed the superplastic deformation with $\varepsilon>1.4$. At temperatures above $460^{\circ}C$, the stress-strain curve of the monolithic BA sample depicted a sharp peak stress and a fellowing stress drop due to cracking, while those of the crystalline-BA composites displayed work-hardening up to the imposed strain. FEM analysis indicated that a fairly homogeneous strain state prevailed throughout the composite, while a higher level of stress was obtained in a harder BA.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.5
• /
• pp.382-386
• /
• 2019

The alignment characteristics of liquid crystal (LC) molecules on a solution-derived lanthanum zinc oxide (LZO) film under ion-beam irradiation were demonstrated. Using the solution process, an LZO film was fabricated on the glass substrate and cured at $100^{\circ}C$. Afterwards, ion-beam irradiation was performed following the LC alignment method. Using this film, an LC cell was fabricated and the characteristics of the LC alignment were verified. Cross polarizing microscopy and the crystal rotation method were used to investigate the alignment state of the LC molecules on the LZO films. Furthermore, field emission scanning electron microscopy and X-ray photoelectron spectroscopy were used to explore the effect of the ion-beam irradiation on the LZO film. Through these, it was confirmed that the ion-beam irradiation induced surface modification, which demonstrated anisotropic physical and chemical surface characteristics. Due to this, uniform LC alignment was achieved. Finally, the residual DC and anchoring energy of the LC cell based on the LZO films were measured using a capacitance-voltage curve.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.6
• /
• pp.243-246
• /
• 2008

We have studied the liquid crystal (LC) alignment, the pretilt angle generation, and the annealing behavior for a nematic liquid crystal (NLC) on the homogeneous polyimide (PI) surfaces by using the rubbing method and the ion beam (IB) method. An excellent LC alignment of the NLC on the PI surface with rubbing and IB irradiation were observed. The pretilt angle of NLC on the homogeneous PI surface for the rubbing method is decreased from $4.5^{\circ}$ to $3.5^{\circ}$ as rubbing time is increased, that of the for the IB irradiation method is decreased from $0.5^{\circ}$ to $0.1^{\circ}$ as the time of IB irradiation is increased. After the annealing, the pretilt angles of the rubbed PI surfaces increased up to $4^{\circ}$, these of the IB irradiated PI surfaces little increased. It is considered the side chain of the rubbed PI show the its abilities of the original capacities, while the side chain of the IB irradiated PI cannot show the its abilities of the original capacities due to the IB has already destroyed the side chain of the PI.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.20 no.1
• /
• pp.64-81
• /
• 1994

O/W emulsions with mixed nonionic surfactants(polyoxyethylene(20)sorbitan monostearate/sorbitan sesquioleate), liquid paraffin, water prepared by direct inversion emulisification method and continuous inversion emulsification Method. The one-step, two-step and three-step phase inversion emulsification method were used in experiments. Effect of added water on droplet size of final O/W emulsions which is prepared by phase inversion emulsification method were investigated. In direct inversion emulsification method(two-step emulsification method), fine and homogeneous droplets of OIW emulsions were formed after phase inversion steps i.e. ,W/O - (W/O) If double emulsion - O/W emulsion. In continuous inversion emulsification method(three-step emulsification method), fine and homogeneous O/W emulsion were formed after phase inversion steps i.e., W/O - pseudomicroemulsion - O/W. By latter method, more Fine and homogenuous droplets were formed than former method. 10-10, 8 HLB region of mixed non-ionic surfactants could produce most fine droplets. This HLB region had maximum values of solubilization water and This HLB value of mixed nonionic surfactants produced fine and homogenuous droplets.