• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.42-45
• /
• 2004

Electrochemical discharge machining (ECDM) has been found to be suitable for the micro-hole machining of nonconductive materials such as ceramics or glass compared with existing conventional and also non-conventional machining methods. However this machining process has some problems such as low geometric accuracy and low machining efficiency due to the random spark generation at the end of the electrode. This paper proposes the methods to improve the geometric accuracy of micro-hole using powder mixed ECDM process. The experimental results show the effects of powder producing improved geometric accuracy of machined hole and decreased concentration of spark energy.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.5
• /
• pp.7-13
• /
• 2010

The integrity and accuracy of the drilling hole are decided by positional error, diameter error, the roundness, the straightness, the cylindericity, size of the burr, the surface roundness and others. Among these parameters, positional error and diameter error have the most important parameters. The diameter error has been widely studied, but there has been little research done about the positional error due to the difficulty of measuring it. The measurement of hole location and diameter would be performed by CMM(Coordinate Measurement Machine). However, the usage of CMM requires much time and cost. In order to overcome the difficulties, we have developed a hole location and diameter error measuring device using machine vision. The developed measurement device attached to a CNC machine can determine hole quality quickly and easily.

• Journal of Welding and Joining
• /
• v.8 no.4
• /
• pp.76-82
• /
• 1990

Lots of research works have been done to improve the accuracy of the hole drilling method to measure residual stress by many investigators. In this study, first, size effect of specimen was analyzed based on the solution of hole in a strip under tension. If the ratio of hole diameter tothe strip width is less than 0.2, the stress distribution around hold may be given from the solution of hole in an infinite plate. Second, the residual stress above $0.6{\sigma}_y$(yield stress) may be measured less than the actual stress by 10-15 percent. Third, eccentricity of hole relative to the rosette center effects on the accuracy of residual stress measurements by 10 percent. The error due to eccentricity of hole can be corrected by the iteration method or the direct method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.121-122
• /
• 2010

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.2
• /
• pp.1-8
• /
• 2004

Applications of the deep hole drilling process can be found in many industries ranging from large aerospace manufacturer to small tool and die shop. Deep hole drilling process with small diameter generally requires high quality and accuracy. But problems which may arise or result from the deep hole drilling process include drill breakage, the generation of a finished part surface which does not satisfy required quality, and process instability. To guaranty the required machining quality and accuracy, it is important to understand and improve the deep hole drilling process. In this study, deep hole drilling experiments using tingle edge drill with small diameter under 2mm have been carried out for difficult to cut materials such as C42CrMo4 and C45pb and the experimental results were analyzed. Feed force and torque versus feed showed linear relationship in both materials. The feed force and torque are decreased as cutting speed is increased but the trends are not uniform in C42CrMo4.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.5
• /
• pp.5-11
• /
• 2011

In this study, the effect of cone angle of seven-hole probe on the accuracy of measured flow angle and velocity has been investigated. The seven-hole probe consisted of seven 1mm OD stainless inner tubes and one 3mm ID stainless tube. Six cone angles of $45^{\circ}$, $60^{\circ}$, $75^{\circ}$, $90^{\circ}$, $105^{\circ}$ and $120^{\circ}$ were tested. Calibrations of the seven-hole probes were conducted within ${\pm}60^{\circ}$ range with the interval of $5^{\circ}$. Analysis results show that the effect on the cone angle was not significant on the accuracy of the measured flow angle, pressure, and velocity. However, the data reduction method had more effect on the measurement accuracy.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10b
• /
• pp.179-188
• /
• 2003

The objective of our study is to investigate the micro fabric ability by conventional metal forming processes. In the present investigation, micro hole punching was studied. We tried to control punching process at the micro level and scaled down the standard blanking condition for $25{\mu}m$ hole fabrication. To accommodate this, tungsten carbide tooling sets and micro punching press were carefully designed and assembled meeting accuracy requirements for $25{\mu}m$ hole punching. With our developments, 100, 50, and $25{\mu}m$ holes were successfully made on metal foils such as brass and stainless steel of 100, 50, and $25{\mu}m$ in thickness, respectively, and hole sizes and shapes were measured and analyzed to investigate fabrication accuracy. Shear behavior during micro punching was also discussed. Our study showed that the conventional punching process could produce high quality holes down to $25{\mu}m$.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.237-240
• /
• 2003

Gas turbines are extensively used in flight propulsion, electrical power generation, and other industrial applications. During its life span, a turbine blade is taken out periodically for repair and maintenance. This includes re-coating the blade surface and re-drilling the cooling holes/channels. A successful laser re-drilling requires the measurement of a hole within the accuracy of ${\pm}0.15mm$ in position and ${\pm}3^{\circ}$ in orientation. Detection of gas turbine blade/vane cooling hole position and orientation thus becomes a very important step for the vane/blade repair process. The industry is in urgent need of an automated system to fulfill the above task. This paper proposes approaches and algorithms to detect the cooling hole position and orientation by using a vision system mounted on a robot arm. The channel orientation is determined based on the alignment of the vision system with the channel axis. The opening position of the channel is the intersection between the channel axis and the surface around the channel opening. Experimental results have indicated that the concept of cooling hole identification is feasible. It has been shown that the reproducible detection of cooling channel position is with +/- 0.15mm accuracy and cooling channel orientation is with +/$-\;3^{\circ}$ with the current test conditions. Average processing time to search and identify channel position and orientation is less than 1 minute.

• Transactions of Materials Processing
• /
• v.14 no.7 s.79
• /
• pp.601-606
• /
• 2005

A hole expansion process is an important process in producing a hub-hole in a wheel disc of a vehicle. In this process, the main parameter is the formability of a material that is expressed as the hole expansion ratio. In the process, a crack is occurred in the upper edge of a hole as the hole is expanded. Since prediction of the forming limit by hole expansion experiment needs tremendous time and effort, an appropriate fracture criterion has to be developed for finite element analysis to define forming limit of the material. In this paper, the hole expansion process of a hub-hole is studied by finite element analysis with ABAQUS/standard considering several ductile fracture criteria. The fracture mode and hole expansion ratio are compared with respect to the various fracture criteria. These criteria do not predict its fracture mode or hole expansion ratio adequately and show deviation from experimental results of hole expansion. A modified ductile fracture criterion is newly proposed to consider the deformation characteristics of a material accurately in a hole expansion process. A fracture propagation analysis at the hub-hole edge is also performed for high accuracy of prediction using the new fracture criterion proposed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.11
• /
• pp.1053-1058
• /
• 2007

Micro-EDM technology (or the manufacture of miniature parts is used to make a micro hole. Two electrode shaping methods, mechanical electrode grinding and WEDG technique, have been studied. In this study, an electrode shaping method by using previously machined hole is introduced in order to obtain an optimal hole-making condition. Key factors such as applied voltage, capacitance, feedrate, and hole-dimension have an influence on the fabricating error of electrode shaping, which are taper ratio of a hole, electrode form accuracy, and electrode surface. Therefore, we try to investigate the optimal fabricating of electrode shaping from various experiments. Results from experiments, it was able to minimize the electrode fabricating error as voltage increases, and also applied feedrate and capacitance decreases.