In order to improve excessive spring-back behavior as a result of the roll forming process using ultra high strength steel (UHSS) sheet, local softening in region of a partial area expected to be deformed on an initial blank is considered in this study. With SPFC1470 UHSS sheet with initial blank thickness of 1.20mm, the local softening is performed with the following conditions: temperatures of 500℃, 550℃, 600℃ and 650℃, and holding time of 20s, 40s, 80s and 160s. Mechanical properties, such as yield stress and tensile strength, as well as elongation, are evaluated through uniaxial tensile tests, while the microstructural characteristics as a result of local softening are also investigated using the heat-treated specimens. As a result, it is shown that the spring-back behavior of the roll-formed prototype was reduced about by 78.9%, when the local softening at about 500℃ was performed for 160s considering the practical manufacturing condition.
The europium doped yttrium oxide (Y2O3:Eu3+) thin film was formed on a Si substrate by the conventional spin-coating process followed by rapid thermal annealing (RTA) treatment. The spinning profiles such as rotation speed, acceleration and holding times were controlled during the spin-coating process for the best condition of the Y2O3:Eu3+ thin film. The RTA treatment was conducted for several temperature in order to crystallize the spin coated film. The Y2O3:Eu3+ thin film presented best performance in the conditions of 4000 rpm, 30 s and 10 s of rotation speed, acceleration time and holding time, respectively, at a fixed RTA temperature of 900 ℃.
Fluoride-salt-cooled High-temperature Reactor (FHR) is a promising nuclear reactor technology. Among many challenges presented by the molten fluoride salts is the corrosion of salt-facing structural components. Higher moisture contents, in the FLiNaK (LiF-NaF-KF, 46.5-11.5-42 mol%) salt, aggravate intergranular corrosion and pitting for the given alloys. Therefore, several thermal dehydration tests of FLiNaK salt were performed with a batch size suitable for thermal-hydraulic experiments. Thermogravimetric Analysis (TGA) was performed for the three constituent fluoride salts individually. Preliminary thermal dehydration plans were then proposed for NaF and KF salts based on the TGA curves. However, the dehydration process may not be required for LiF since its low mass loss (<1.3 wt%). To evaluate the performance of these thermal dehydration plans, a batch-scale salt dehydration test facility was designed and constructed. The preliminary thermal dehydration plans were tested by varying the heating rates, target temperature, and holding time. The sample mass loss data showed that the high temperatures (>500 ℃) were necessary to remove a significant amount of moisture (>1 wt%) from NaF salt, while relatively low temperatures (around 300 ℃) with a long holding time (>10 h) were sufficient to remove most of the moisture from KF salt.
The effects of oxygen plasma treatments at different discharge power, reaction pressure, treatment time on yellowing of polyester fabrics were studied. Surface characteristics of the treated fabrics were also investigated by means of SEM and ESCA. The results were as follows : The yellowing of fabrics increases as the power and the treatment time are increased, and decreases as the pressure is increased. The plasma treatment of 100 Watt, 200 mTorr, 5 min. is the optimal condition which is most effective in holding whiteness as well as high weight loss of fabrics.
일반적으로 음성전화망에서 수학적 모델을 사용하여 트래픽 분석을 수행하는 경우 호 도착 시간과 채널 보류 시간은 지수 분포라고 가정한다. 본 논문에서는 이동전화망을 구성하고 있는 교환기에서 추출한 과금 데이터를 이용하여 호 발생으로 인해 집계되는 호량애 관한 호 도착 시간과 채널 보류 시간이 나타내는 분포를 알아본다. 또한 분석된 확률 분포를 통계적 검정 방법을 이용하여 경험분포함수에 대한 기대 분포함수의 적합성을 판별한다.
서울시내 종합병원 병상 규모를 3 group으로 분류하여 5개병원을 대상병원으로 선정한 후 완자전과 육개장을 대상 음식으로 하여 각 생산 단계의 소요시간, 온도 상태 및 미생물적 품질평가를 실시하여 HACCP 방법으로 위험요인 분석을 실시하였다. 기본재료의 미생물적 품질상태가 저조한 것으로 평가되었고, 배달과정 및 검수 후 저장단계에서 냉장고의 철저한 온도관리가 요구되었다. 음식생산 과정에서의 소요시간-온도상태의 기준이 적절히 시행되고 있지 못하였다. 음식 생산과정에서 사용되는 기구, 기기, 및 용품에 대한 미생물 검사 결과 즉각적인 시정이 요구되었다. 완자전 생산과정에서의 각 병원별 criticla control point는 A병원: 기본재료, 전처리단계, 조리단계, 조리후 보관단계 ; B병원 : 기본재료, 전처리단계 ; C병원: 기본재료, 전처리단계, 조리후 보관단계 및 급식단계 ; D병원 : 기본재료 전처리단계 , 조리후 보관 단계 및 급식단계 ; E 병원: 기본재료, 전처리 단계 , 조리후 보관단계 및 급식단계로 지적되었다.
고분자 전해질 연료전지(PEMFC) 고분자 막의 전기화학적 내구성을 가속적으로 평가하는 개회로 전위 유지(OCV holding) 과정에서 OCV 변화 거동을 해석하는 것은 매우 중요하다. 본 연구에서는 내구성이 각기 다른 세 종류의 MEA(membrane electrode assembly)의 실험데이터를 이용한 실험식을 만들어 비교 및 검토하였다. 막 내부에 라디칼 제거제가 없는 강화막 MEA의 내구 평가시간은 383 h, 막 내부에 라디칼 제거제가 있는 강화막 MEA의 내구 평가시간은 각각 1,000, 1,650 h이었다. 고분자 막의 열화는 활성화에 의해 회복이 가능한 가역적 열화와 회복이 되지 않은 비가역적 열화로 구분했다. 고분자 막의 비가역적 열화는 수소투과도 증가로 나타나는데 수소투과도 변화가 세 MEA 모두 비가역적 열화 상수 c와 유사한 형태를 보였다. 회복이 되지 않은 비가역적 열화가 시작되는 것은 수소투과도 증가로 나타나고, 수소투과도 증가로 인해 OCV가 회복되지 않아서 OCV 회복선의 기울기가 감소하고 이를 실험식의 상수 c 값의 증가로 확인할 수 있었다.
This paper describes the design of a force applying system for a smart phone curved glass molding system and its characteristic test. The force applying system is composed of a motor and gear, a rectilinear movement structure, a force sensor, an LVDT (Linear Variable Differential Transformer) sensor, an up and down moving block, and so on. The system precisely controls the applying force and time to the plane glass because the glass can be easily destroyed under applied force, and can be bent imperfectly. As a result of the characteristic test, the curved glass can be manufactured using this system, and the holding time under 0N force, the applying force to the plane glass, the time for applying from 0N to maximum force, and the holding time under maximum force at the manufacture feasible temperature $620^{\circ}C$ were found.
This study was conducted to establish a freezing method of miniature pig spermatozoa. The semen 더aculated from PWG M-type miniature pig was collected by gloved-hand method. The semen was diluted with same volume extender (m-Modena B). The frozen solution used frozen solution of four different (LEY, TCG, BF-5 and m-Modena+egg yolk) for find optimal frozen solution in miniature pig sperm. The diluted semen for frozen rate assay was added to LEY solution (solution I: 11% lactose+egg yolk; solution II: solution I+glycerol+OEP), and frozen depending on freezing rate by the three different freezing methods (A: until $5^{\circ}C$ for 1 hrs, holding at $-102^{\circ}C$ for 10 min; B: until $5^{\circ}C$ for 2 hrs, holding at $-102^{\circ}C$ for 10 min; C: until $5^{\circ}C$ for 3 hrs, holding at -80 and $-102^{\circ}C$ for 10 min). Semen cooled until $5^{\circ}C$ was added with glycerol 1, 3 and 5%, and take a equilibrium time for 0, 10 and 30min. Frozen-thawed sperm were evaluated for viability, acrosomal status and morphological abnormality. The results of frozen-thawed sperm ability by frozen solution, viability was higher in LEY solution compared to other three different frozen solution. AR pattern of LEY solution were lower than other three different frozen solution. The results of freezing rate, viability was higher in B method compared to other methods (p<0.05). Acrosomal statute was intacted in A and B methods than C method. The experiment for glycerol condition was showed that sperm viability was higher in extender with 1% and 3% glycerol and equilibrium time of 0 min. The acrosome damage was lower in extender with 1% glycerol and equilibrium time of 10 min than other conditions. In conclusion, the optimal conditions for cryopreservation of miniature pig spermatozoa obtained in LEY frozen solution, cooling rate of 1~2 hrs, 1~3% glycerol concentrations and glycerol equilibrium time of 0~10 min.
We discuss scheduling analysis for a discrete event system with time windows of which firing or holding time delays are subject to random variation within some finite range. To do this, we propose a modified p-lime Petri net, named p+-time Petri net. We develop a condition for which a synchronized transition does not have a dead token, that is, the firing epochs do not violate the time window constraints. We propose a method of computing the feasible range of the token sojourn time at each place based on a time difference graph. We also discuss an application for analyzing wafer residency times within the process chambers for a dual-armed cluster tool for chemical vapor deposition.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.