• Nuclear Engineering and Technology
• /
• v.55 no.6
• /
• pp.2088-2095
• /
• 2023

The safety of nuclear installations is largely determined by the tightness of fuel elements cladding. As the Fukushima nuclear accident showed, the main task in case of loss of power supply is to ensure reliable removal of residual heat release from spent fuel pool (SFP) with irradiated fuel assemblies (IFAs). The paper presents the results of calculated-experimental studies and thermal-hydraulic modeling of temperature storage modes of IFAs in SFP. Experimental studies of SFP's temperature regime and calculated evaluation of residual heat removal due to the thermal conductivity of building structures surrounding the SFP were performed. To ensure the safe operation of research reactors, it's necessary to know the IFA's residual heat power (RHP) in the reactor and SFP, which is determined depending on the operating time of fuel assemblies (FAs) and the IFAs calculated holding time. The FAs operating time depends on the reactor energy output. The IFAs calculated holding time is determined by the fuel burnup, U-235 mass in the fuel, and reactor utilization factor. The IFAs fuel burnup was calculated using the MCU-PTR program. Also presented are the RHP's calculation results using some of the empirical dependencies. The concept of a passive heat removal system (PHRS) based on thermosyphon's operating principle was proposed.

• Korean Journal of Applied Biomechanics
• /
• v.25 no.1
• /
• pp.65-76
• /
• 2015

Objective : The purpose of this study was to analyse the differences in core stability and muscle balance of the pilates Teaser motion according to the surfaces and skills. Methods : There were 10 subjects in this study with 5 being skilled and 5 that were not skilled. The independent variables were surfaces (high elastic & aluminum) and skills (skilled & unskilled). Dependent variables were core stability and muscle balance. Core stability was measured by Force Platform (9872, Switzerland), 3D Imagery (IBS-2000, EXYMA) was used to understand the muscle balance. In order to do the Teaser movement subjects had to lay flat on their back and then lean forward as much as possible and hold the position for 10 seconds. Afterwards, they would lay back down again. A camera (MHS-PM5K, SONY) was used to make 4 phases (take off, recoil forward, holding, recoil backward) during the teaser exercise to analyze movement. In this study quantitative and qualitative analysis was used. For the statistical analysis, 2X2 ANOVA was used to analyze the differences in movement time, X,Y,Z maximum force, center of pressure and angles according to different phases. 2X3 ANOVA was used to analyze the differences in muscle balance via SPSS 18.0. Results : Soft. Elastic mat had a longer holding time, lower Fx/ Fy/ Fz, shorter Fx trajectory, larger angle and shorter gaps in muscle balance than a hard surface in skilled subjects. This was because the mat can help to recruit and then sustain core fine muscles during holding time in the Teaser movement.

• Transactions of Materials Processing
• /
• v.14 no.4 s.76
• /
• pp.384-391
• /
• 2005

The nickel-based alloy Nimonic 80A possesses the excellent strength, and the resistance against corrosion, creep and oxidation at high temperature. Its products are used in aerospace engineering, marine engineering and power generation, etc. Control of forging parameters such as strain, strain rate, temperature and holding time is important because change of the microstructure in hot working affects the mechanical properties. Change of the microstructure evolves by recovery, recrystallization and grain growth phenomena. The dynamic recrystallization evolution has been studied in the temperature range of $950\~1250^{\circ}C$ and strain rate range of $0.05\~5s^{-1}$ using hot compression tests. The metadynamic recrystallization and grain growth evolution has been studied in the temperature range of $950\~1250^{\circ}C$ and strain rate range $0.05,\;5s^{-1}$, holding time range of 5, 10, 100, 600 sec using hot compression tests. Modeling equations are proposed to represent the flow curve, recrystallized grain size, recrystallized fraction and grain growth phenomena by various tests. Parameters in modeling equations are expressed as a function of the Zener-Hollomon parameter. The modeling equation for grain growth is expressed as a function of the initial grain size and holding time. The modeling equations developed were combined with thermo-viscoplastic finite element modeling to predict the microstructure change evolution during hot forging process. The grain size predicted from FE simulation results is compared with results obtained in field product.

• Journal of the Korean Ceramic Society
• /
• v.42 no.8 s.279
• /
• pp.567-574
• /
• 2005

Densification of SiC powder with additives of total amount of2, 4, 8 $wt\%$ Al-B-C was carried out by Spark Plasma Sintering (SPS). The unique features of the process are the possibilities of a very fast heating rate and a short holding time to obtain fully dense materials. The heating rate and applied pressure were kept at $100^{\circ}C/min$ and 40 MPa, while the sintering temperature and holding time varied from 1700 - $1800^{\circ}C$ for 10 - 40 min, respectively. The SPS-sintered specimens with different amount of Al-B-C at $1800^{\circ}C$ reached near-theoretical density. The $3C{\rightarrow}6H,\;15R{\rightarrow}4H$ phase transformation of SiC was enhanced by increasing the additive amount. The microstructure of SiC sintered up to $1750^{\circ}C$ consisted of fine equiaxed grains. In contrast, the growth of large elongated grains in small matrix grains was shown in sintered bodies at $1800^{\circ}C$, and the plate-like grains interlocking microstructure had been developed by increasing the holding time at $1800^{\circ}C$. The grain growth rate decreases with increasing amount of Al-B-C in SiC starting powder, however, the both of volume fraction and aspect ratio of large grains in sintered body increased.

• Journal of the Korean Ceramic Society
• /
• v.46 no.6
• /
• pp.615-620
• /
• 2009

The present research was performed to determine the optimal firing condition and holding time for malayaite crystal, which is responsible for the stable pink-red coloration in glaze at high temperatures, using Cr$Cl_3$ as chromophore for the synthesis of $Cr_2O_3-SnO_2-CaO-SiO_2$ system pigments. The malayaite crystal was influenced by the raw materials used for synthesis, firing temperature, and holding time. Thus there are differences in the crystal phase and in the coloration according to the condition of synthesis. When Cr$Cl_3$ was used as chromophore, the pigment could be synthesized at lower temperatures, because Cr$Cl_3$ melts at $1500{^{\circ}C}$, which is much lower than the temperature at which $Cr_2O_3$ melts (higher than $2435{^{\circ}C}$). And the employed Cr ion showed a change in oxidation state. When a mineralizer was used to improve the employment of malayaite and the Cr ion, and the low temperature was maintained at which the malayaite crystal is produced, the production of malayaite crystal was promoted and the employment of chromophore was also promoted in the oxidation state of Cr (IV). The results of the experiment showed that the optimal firing condition was 18 h of holding time at $800{^{\circ}C}$, using Cr$Cl_3$ as chromophore, followed by 2 h at the raised temperature of $1150{^{\circ}C}$. The change in coloration of the Cr (IV) employed by malayaite showed a very rich color of red. Thus it was possible to effectively synthesize sphene-pink pigments with more red tint at a low temperature.

• Journal of the Korean Ceramic Society
• /
• v.26 no.4
• /
• pp.459-470
• /
• 1989

Single crystals of rare-earth iron garnets were grown from solutions of molten lead oxide, lead fluoride, baric oxide, iron oxide, and the oxides of yttrium, samarium orgadolinium. The crystals were grown by slow cooling technique. A convenient composition was 41.8mol% PbO, 20.59mol% PbF2, 8.23mol% B2O3, 20.00mol% Fe2O3 and 10.00mol% R2O3 where R is Y, Sm or Gd. For this experiment, platinum crucibles of size 20, 30cc and a vertical siliconit tube furnace were used. The precipitation temperature of YIG was observed in the range of 115$0^{\circ}C$-112$0^{\circ}C$ and the optimum growth conditions in this experiment were determined. The nucleation rate was controlled by the holding time after the fast colling, the growth rate by the slow cooling conditiions. The form of the grown YIG crystals showed a combination of {110} and {211}, and the size of the crystals grown in this experiment was up to about 9mm under the conditions of holding time 16hour, cooling rate 2$^{\circ}C$/hr. and temperature range 115$0^{\circ}C$-90$0^{\circ}C$. The precipitatin temperature of SmIG was observed in the range of 105$0^{\circ}C$-98$0^{\circ}C$ and the size of the crystals grown in this experiment was up to about 5mm under the conditiions of holding time 16hours, cooling rate 2$^{\circ}C$/hr. and temperature range 100$0^{\circ}C$-80$0^{\circ}C$.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.1
• /
• pp.1-12
• /
• 1991

This study has been performed to find out the effect of austenitizing temperature, austempering temperature and its holding time, and tempering cycle on the mechanical properties such as impact resistance, hardness etc. of AISI $M_2$ Mo series high speed tool steel austempered or tempered after austempering treatment. The results obtained from the experiment are as follows ; (1) Optical micrograph has revealed that the transformation rate of bainite is delayed as the austenitizing temperature increases and that bainite is most apparently transformed at an austempering temperature of $290^{\circ}C$. (2) The amount of retained austenite during austempering has been analysed to be increased by the X-ray diffraction technique as the transformation product of bainite is increased. It has also been shown that the longer the holding time of austempering, the more the transformation quantity of bainite is formed, exhibiting, however, that the rate of bainitic transformation is considerably retarded after a certain period of holding time elapses. (3) Hardness measurement has shown that hardness values obtained after austempering increase with decreasing the amount of retained austenite. (4) The austempering and then tempering cycle has been formed to give hardness values which are more greatly improved as austenitizing temperature is increased. (5) The mechanical property of the specimen primary-tempered for 1 hour at $550^{\circ}C$ after austempering for 2 hours at $290^{\circ}C$ from the austenitizing temperature range of $1180^{\circ}C$ to $1210^{\circ}C$ have been estimated to be good values.

• Korean Journal of Food Science and Technology
• /
• v.47 no.6
• /
• pp.772-778
• /
• 2015

Hydrolysis of isolate soybean protein (ISP) using subcritical water (SCW) was conducted to study the feasibility for producing protein hydrolyzate. SCW hydrolysis of SPI suspension (5-15%) was conducted in an electrically heated batch reactor (2 L). The effects of temperature (230 to $270^{\circ}C$) and holding time (10 to 50 min) on the degree of hydrolysis (DH) and the production of amino acids were studied by surface response method. The DH was determined by derivatizing the hydrolyzates with ortho-phthalaldehyde (OPA) solution. It was confirmed that reaction temperature and holding time affected the hydrothermolysis of soybean protein. However, the holding time was less effective on amino acid yield when the temperature was higher than $230^{\circ}C$. In order to achieve optimal yields of amino acids exceeding 43%, the temperature should be within the range between 256 and $268^{\circ}C$ with holding time from 29 to 41 min, respectively. A maximum estimated amino acid yield of 43.5% was obtained at $268^{\circ}C$ for 35 min.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.62 no.2
• /
• pp.17-29
• /
• 2020

The objective of this study was to find an optimum methane yield condition in anaerobic digestion of sewage sludge with microwave pretreatment. The pretreatment process was carried out using a lab scale industrial microwave unit (2,450 MHz frequency). The digestion efficiency of pretreated sludge was evaluated by biochemical methane potential (BMP) test. Box-Behnken design and Response Surface Analysis (RSA) were applied to determine the optimal combination of sludge mixing ratio (0 to 100%), power (400 to 1600 W), holding time (0 to 10 min) and pretreatment temperature (60 to 100℃). BMP test results showed that Volatile Solid (VS) removal efficiency was up to 48% at a condition of 0% for mixing ratio, 1600 W for power, 5 min for holding time, and 80℃ for pretreatment temperature. Methane production was up to 832.3 mL/g VS_removed at a condition of 50% for mixing ratio, 1000 W for power, 5 min for holding time, and 80℃ for pretreatment temperature. The results of the variance analysis (ANOVA) showed that the p-value of the power and pretreatment temperature among the independent variables were significant (p<0.05), and in particular, the pretreatment temperature significantly affected on the solubilization and methane production. The optimum condition for the maximum methane yield (847 mL/g VS_removed) was consist of 38.4% of mixing ratio, 909.1 W of power, 4.1 min of holding time, and 80℃ of temperature within the design boundaries.

• Journal of Powder Materials
• /
• v.18 no.4
• /
• pp.365-371
• /
• 2011

In this study, gradient porous Al-Cu sintered body was fabricated by powder metallurgy processing. Al-Cu powder mixtures were prepared by low energy ball milling with various milling time. After ball milling for 3h, the shape of powder mixtures changed to spherical type with size of 100~500 ${\mu}m$. Subsequently, Al-Cu powder mixtures were classified (under 150, 150~300 and over 300 ${\mu}m$) and compacted (20, 50 and 100 MPa). Then, they were sintered at $600^{\circ}C$ for various holding time (10, 30, 60 and 120 min) in $N_2$ atmosphere. The sintered bodies had 32~45% of porosity. As a result, the optimum holding time was determined to be 60 min at $600^{\circ}C$ and sintered bodies with various porosity were obtained by controlling the compacting pressure.