• 한국재료학회지
• /
• 제14권5호
• /
• pp.328-333
• /
• 2004

Transparent ZnO:Al conductor films for the optoelectronic devices were deposited by using the capacitively coupled DC magnetron sputtering method. The effect of Al doping concentration and discharge power on the electrical and optical properties of the films was studied. The film resistivity of $8.5${\times}$10^{-4}$ $\Omega$-cm was obtained at the discharge power of 40 W with the ZnO target doped with 2 wt% $Al_2$$_O3$. The transmittance of the 840 nm thick film was 91.7% in the visible waves. Increasing doping concentration of 3 wt% $Al_2$$O_3$ in ZnO target results in significant decrease of film resistivity, which may be due to the formation of $Al_2$$O_3$ particles in the as-deposited ZnO:Al film and the reduced ZnO grain sizes. Increasing DC power from 40 to 60 W increases deposition rate by more than 50%, but can induce high defect density in the film, resulting in higher film resistivity.

• 폴리머
• /
• 제35권5호
• /
• pp.458-466
• /
• 2011

초임계 탄산가스/유기용매 혼합계 상에서 이색성 염료인 C. I. direct black 22(DB22)로 고검화도의 폴리(비닐 알코올)(PVA)을 염색하여 내구성이 강한 편광필름을 제조하였다. 특히, 초임계 탄산가스 상으로 이색성 염료를 녹이기 위한 분산제로 에틸렌 글리콜과 디메틸 설폭사이드의 무게비=4 : 6의 혼합용매계를 사용하였을 때 염색 압력을 200 bar까지 낮출 수 있었다. 초임계 유체계의 사용으로, 최대 염색은 연신 전 투과도로 1% 미만까지, 폐수 발생량은 1/10 수준까지, 감소가 가능하였고, 이와 같이 염색된 PVA 필름을 500% 연신한 후 측정된 편광효율은 94%, 평균 투과도(single piece transmittance)는 30%로 각각 얻어졌으며, 또한 이색성 염료로서의 DB22의 한계 및 개선 방안 등도 검토하였다.

• 한국전기전자재료학회논문지
• /
• 제19권1호
• /
• pp.87-90
• /
• 2006

In case of preparation of ITO thin film for using top electrode of Top-emitting Organic Light Emitting Diodes(TOLEDs), the ITO thin film should be prepared at room temperature and low oxygen gas flow condition in order to reduced the damage of organic layer due to the bombardment of highly energetic particles such as negative oxygen ions which accrued from the plasma. In this study, the ITO thin film with high optical transmittance and low resistivity prepared as a function of oxygen gas (0 ${\~}$ 0.8 sccm) and Ar gas was fixed at 20 sccm by the Facing Targets Sputtering (FTS) method. The electrical and optical properties of ITO thin films were measured by Hall effect measurement, UV/VIS spectrometer, respectively In the results, we obtained the ITO thin film with lowest resistivity($3{\times}10^{-4} {\Omega}{\cdot} cm$) at oxygen gas flow 0.2 sccm and optical transmittance over $80\%$ at oxygen gas flow over 0.2 sccm.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.853-856
• /
• 2005

we proposed the optimized conditions of the uniaxial and biaxial compensation films to suppress the light leakage to improve viewing angle characteristics. Compared with conventional OCB mode, the maximum transmittance is increased about 30% and the minimum transmittance is slightly decreased. From here results, we can about OCB mode with wide viewing angle and high contrast ratio.

• 한국재료학회지
• /
• 제23권4호
• /
• pp.215-218
• /
• 2013

Vanadium dioxide ($VO_2$) is an attractive material for smart window applications where the transmittance of light can be automatically modulated from a transparent state to an opaque state at the critical temperature of ${\sim}68^{\circ}C$. Meanwhile, F : $SnO_2$ (F-doped $SnO_2$, FTO) glass is a transparent conductive oxide material that is widely used in solar-energy-related applications because of its excellent optical and electrical properties. Relatively high transmittance and low emissivity have been obtained for FTO-coated glasses. Tunable transmittance corresponding to ambient temperature and low emissivity can be expected from $VO_2$ films deposited onto FTO glasses. In this study, FTO glasses were applied for the deposition of $VO_2$ thin films by pulsed DC magnetron sputtering. $VO_2$ thin films were also deposited on a Pyrex substrate for comparison. To decrease the phase transition temperature of $VO_2$, tungsten-doped $VO_2$ films were also deposited onto FTO glasses. The visible transmittance of $VO_2$/FTO was higher than that of $VO_2$/pyrex due to the increased crystallinity of the $VO_2$ thin film deposited on FTO and decreased interface reflection. Although the solar transmittance modulation of $VO_2$/FTO was lower than that of $VO_2$/pyrex, room temperature solar transmittance of $VO_2$/FTO was lower than that of $VO_2$/pyrex, which is advantageous for reflecting solar heat energy in summer.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.826-828
• /
• 2003

With a new PDP transparent dielectric layer formation technique, we were able to make dielectric layer with high transmittance by using dry film type dielectric material. We optimized dielectric pastes for dry film and they showed good process properties in lamination , drying and firing.

• 한국세라믹학회지
• /
• 제56권4호
• /
• pp.354-359
• /
• 2019

Information security films that can ensure personal privacy by reducing the viewing angle of display screens were fabricated by microlouver patterning and a ZnO nano-ink filling process. Optical simulation results demonstrated that all the microlouver films showed good security performances. Security performances were evaluated as calculated relative luminance ratios compared between the side and front. Based on the simulation results, microlouver films were fabricated by UV imprint lithography and nano-ink bar coating. However, distortion of the microlouver pattern occurred with the use of high-viscosity nano-inks such as ZrO₂ and TiO₂, and the CuO-filled microlouver film suffered from very low optical transmittance. Accordingly, the effects of ZnO filling height on security performance were intensively investigated through simulation and experimental measurements. The fabricated microlouver film with a 75-㎛-high ZnO filling exhibited a good relative luminance ratio of 0.75 at a 60° side angle and a transmittance of 44% at a wavelength of 550 nm.

• 반도체디스플레이기술학회지
• /
• 제15권1호
• /
• pp.6-11
• /
• 2016

For high volume manufacturing using extreme ultraviolet (EUV) lithography, mask protection from contamination during lithography process must be solved, and EUV pellicle is the strongest solution. Based on the technical requirements of EUV pellicle, EUV pellicle should have large membrane area ($110{\times}140mm^2$) with film transmittance over 90% and mechanical stability. Even though pellicle that satisfies size standard with high transmittance has been reported, its mechanical stability has not been confirmed, nor is there a standard to evaluate the mechanical stability. In this study, we suggest a rather simple method evaluating mechanical stability of pellicle membrane using spin-coater which can emulate the linear accelerated motion. The test conditions were designed by simulating the acceleration distribution inside pellicle membrane through correlating the linear acceleration and centripetal acceleration, which occurs during linear movement and rotation movement, respectively. By these simulation results, we confirmed the possibility of using spin-coater to evaluate the mechanical stability of EUV pellicle.

• Current Photovoltaic Research
• /
• 제5권3호
• /
• pp.75-82
• /
• 2017

High efficiency thin film solar cells require an absorber layer with high absorption and low defect, a transparent conductive oxide (TCO) film with high transmittance of over 80% and a high conductivity. Furthermore, light can be captured through the glass substrate and sent to the light absorbing layer to improve the efficiency. In this paper, morphology formation on the surface of glass substrate was investigated by using HF, mainly classified as random etching and periodic etching. We discussed about the etch mechanism, etch rate and hard mask materials, and periodic light trapping structure.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.1428-1429
• /
• 2009

Compared to the indium zinc oxide (IZO) film fabricated by micro-powder target, the IZO film with nano-powder target exhibited improved optoelectronic properties of wide bandgap, high transmittance, surface uniformity, and low sheet resistance due to the high film density.