• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.4
• /
• pp.469-477
• /
• 2015

In this study, the characteristics of main wind direction, vertical temperature and wind speed profile near the Moseulpo airfield for HALE UAV(High Altitude Long Endurance Unmaned Aerial Vehicle) is investigated. The results are summarized as follows, main wind direction is governed by air mass according to season and local wind such as land-sea breeze. The directions of landing and take-off of HALE UAV will be selected as the south-east direction in June ~ August, north-west direction in October ~ March, and south-east direction at daytime in April ~ May, September. Annual variation of temperature at 100 hPa showed that temperature in summer season is lower than winter season. On the other hands, wind speed at 250 hPa in winter season is higher than summer season. The threshold values of temperature and wind speed for HALE UAV flight are $-75^{\circ}C$ and $90ms^{-1}$, which were determined by 5 % frequency value($1.96{\sigma}$), respectively.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.6
• /
• pp.1115-1120
• /
• 2017

In this paper, we apply the LMMSE(: Linear Minimum Mean Square Error) algorithm to overcome the Doppler effect according to the UAV(: Unmanned Aerial Vehicle) velocity in multipath fading channel environment. Simulation results show that the performance difference depends on the pilot arrangement and pattern, and we confirmed that the frame structure proposed in this paper can provide a stable secondary link for high speed UAV system.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.1
• /
• pp.132-138
• /
• 2016

Korea Aerospace Research Institute (KARI) is developing an electric-driven HALE UAV in order to secure system and operational technologies since 2010. Based on the flight tests and design experiences of the previously developed electric-driven UAVs, KARI has designed EAV-3, a solar-powered HALE UAV. EAV-3 weighs 53kg, the structure weight is 22kg, and features a flexible wing of 19.5m in span with the aspect ratio of 17.4. Designing the main wing and empennage of the EAV-3 the amount of the bending due to the flexible wing, 404mm at 1-G flight condition based on T-800 composite material, and side wind effects due to low cruise speed, $V_{cr}=6m/sec$, are carefully considered. Also, unlike the general aircraft there is no center of gravity shift during the flight because of the EAV-3 is the solar-electric driven UAV. Thus, static margin cuts down to 28.4% and center of gravity moves back to 31% of the Mean Aerodynamic Chord (MAC) comparing with the previously designed the EAV-2 and EAV-2H/2H+ to upgrade the flight performance of the EAV-3.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.513-520
• /
• 2004

A steady-state/transient performance simulation model was newly developed for the propulsion system of the CRW (Canard Rotor Wing) type UAV (Unmanned Aerial Vehicle) during flight mode transition. The CRW type UAV has a new concept RPV (Remotely Piloted Vehicle) which can fly at two flight modes such as the take-off/landing and low speed forward flight mode using the rotary wing driven by engine bypass exhaust gas and the high speed forward flight mode using the stopped wing and main engine thrust. The propulsion system of the CRW type UAV consists of the main engine system and the duct system. The flight vehicle may generally select a proper type and specific engine with acceptable thrust level to meet the flight mission in the propulsion system design phase. In this study, a turbojet engine with one spool was selected by decision of the vehicle system designer, and the duct system is composed of main duct, rotor duct, master valve, rotor tip-jet nozzles, and variable area main nozzle. In order to establish the safe flight mode transition region of the propulsion system, steady-state and transient performance simulation should be needed. Using this simulation model, the optimal fuel flow schedules were obtained to keep the proper surge margin and the turbine inlet temperature limitation through steady-state and transient performance estimation. Furthermore, these analysis results will be used to the control optimization of the propulsion system, later. In the transient performance model, ICV (Inter-Component Volume) model was used. The performance analysis using the developed models was performed at various flight conditions and fuel flow schedules, and these results could set the safe flight mode transition region to satisfy the turbine inlet temperature overshoot limitation as well as the compressor surge margin. Because the engine performance simulation results without the duct system were well agreed with the engine manufacturer's data and the analysis results using a commercial program, it was confirmed that the validity of the proposed performance model was verified. However, the propulsion system performance model including the duct system will be compared with experimental measuring data, later.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.499-505
• /
• 2004

A Propulsion System of the CRW(Canard Rotor Wing) type UAV(Unmanned Aerial Vehicle) was composed of the turbojet engine to generate the propulsive exhaust gas, and the duct system including straight bent ducts, tip-jet nozzles, a master valve and a variable main nozzle for three flight modes such as lift/landing mode, low speed transition flight mode and high speed forward flight mode. In this study, in order to operate safely the propulsion system, the dynamic Performance behavior of the system was modeled and simulated using the SIMULIN $K^{ }$, which is the user-friendly GUI type dynamic analysis tool provided by MATLA $B^{ }$. In the transient performance model, the inter-component volume model was used. The performance analysis using the developed models was performed at various flight condition, valve angle positions and fuel flow schedules, and these results could set the safe flight mode transition region to satisfy the inlet temperature overshoot limitation as well as the compressor surge margin. Performance analysis results using the SIMULIN $K^{ }$ performance program were compared with them using the commercial program GSP.m GSP.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.9
• /
• pp.46-53
• /
• 2014

In this paper, ku-band RF transceiver system is designed for the unmanned aerial vehicle(UAV) line-of-sight(LOS) datalink. The RF transceiver system is consisted of the transmitting and receiving unit, RF front-end unit, and high power amplification unit. The transmitting and receiving unit has the functions of frequency up/down converting and channel changing. The RF front-end unit has the functions of transmitting and receiving signal duplexing, antenna selection, small signal amplification, and frequency filtering excluding the receiving signal. The high power amplification unit has the functions of ku-band power amplification and transmitting power variation(High/Middle/Low/Mute). The frequency up/down converting of transmitting and receiving unit is designed by using the superheterodyne method. The RF transceiver system is designed to obtain the broadband and high linearity properties for the reliable transmission and reception of high data-rate and high speed data. Also, the channel changing function is designed to use selectively the frequency as the operation environment of UAV.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.4
• /
• pp.1343-1351
• /
• 2014

Recent technological advances in wireless networks and microelectromechanical systems (MEMS) have led to the development of different types of mini-UAVs and their utilizations in various ways. This study endeavors to develop a low-cost mini-UAV with autonomous flight capability, in order to obtain geospatial information of a small or medium-sized area, and also assess its flight stability by comparing the predetermined flight paths against the actual flight paths. Based on a post-development flight test, stable flight has been proven achievable as follows: the maximum endurance speed is 1 hour, the flying distance is 50km, the horizontal accuracy of flight paths is about ${\pm}6{\sim}8m$, and the altitude accuracy is about ${\pm}8m$. Therefore, it is deemed that high-resolution images which can be utilized for geospatial information are obtainable. This indicates that a UAV flying at an altitude of 200m can acquire images across a $2km{\times}3km$ area on the ground within 25 minutes, which validates its high usability for obtaining high-solution images at low altitudes in the future.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.177-182
• /
• 2003

In this study, a performance model of the Smart UAV propulsion system with ducts, tip jets and variable main nozzle, which has flight capability of the rotary wing mode for the take-off/landing and low speed forward flight as welt as the fixed wing mode for high speed forward flight, has been newly developed. With the proposed model, steady-state performance analysis was performed at various flight modes and conditions, such as rotary wing mode, fixed wing mode, compound wing, mode altitude and flight speed. In investigation of performance analysis, it was noted that the operational capability of the propulsion system was limited due to the duct losses depending on each flight mode, and the limitation with the altitude variation case has much greater than that with the flight speed variation case.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.10
• /
• pp.1017-1025
• /
• 2008

The air data system(ADS) was developed for unmanned aerial vehicle(UAV) in this paper. Generally, the ADS helps flight control computer(FCC) to control the UAV above the stall speed and to hold the given altitude. The accurate measurement of airspeed and altitude of UAV is important because it indicates a flight performance and assures a safe flight. The ADS consists of MEMS pressure sensors, a lowpass filter, a micro controller unit and a pitot-tube. The ADS errors were reduced by pressure and temperature compensation of MEMS sensors. Finally, the altitude and airspeed data of the ADS was compared with GPS data in the flight test.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.5
• /
• pp.1-9
• /
• 2004

The performance analysis code has been developed for vertical take-off and landing(VTOL) UAV which can be utilized as a trade analysis tool in the pre-conceptual design phase. The UAV requires VTOL capability and high speed cruise performance. The main logic of this performance analysis code is to estimate performance parameters of each mission segment by mission fuel weight iteration. The reliability of this performance analysis code is discussed by comparing the data of existing dual flight mode VTOL UAVs such as Boeing CRW and Bell Tilt Rotor.