• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.1092-1095
• /
• 2001

Steady state thermal analysis has been done by a finite element method in a diode of 12kV blocking voltage. The diode was fabricated by soldering ten pieces of 1200V diodes in series, capping a dummy wafer at the far end of diode series, and finally wire bonded for building anode and cathode terminal. In order to achieve high voltage and reliability, the edge of each diode was beveled and passivated by resin with a thickness of 25${\mu}$m. It was assumed that the generated heat which is mainly by the on-state voltage drop, 9V for 12kV diode, is dissipated by way of the conduction through diodes layers to bonding wire and of the convection at the surface of passivating resin. It was predicted by the thermal analysis that the temperature rise of a pn junction of the 12kV diode can reach at the range of 16∼34$^{\circ}C$ under the given boundary conditions. The thickness and thermal conductivity(0.3∼3W/m-K) of the passivating resin did little effect to lower thermal resistance of the diode. As the length of the bonding wire increased, which means the distance of heat conduction path became longer, the thermal resistance increased considerably. The thermal analysis results imply that the generated heat of the diode is dissipated mainly by the conduction through the route of diode-dummy wafer-bonding wire, which suggests to minimize the length of the wire for the lowest thermal resistance.

• 자원환경지질
• /
• 제43권3호
• /
• pp.259-267
• /
• 2010

국내에서 노멀전기검층은 지반조사, 지하수 환경조사, 지열조사, 지질조사, 광물자원 평가 등의 다양한 분야에서 널리 이용되고 있다. 노멀전기검층은 지표 전기비저항탐사법과는 달리 완전공간에 대한 자료를 취득하기 때문에 지표부근에 수위가 위치하는 시추공에서 자료를 취득하는 경우, 수위 및 지표에 대한 영향을 고려해야 한다. 이 연구는 노멀전기검층 존데, 전류리턴전극, 기준점전위전극, 시추공내 지하수위 등을 포함하는 실제 물리검층 환경과 동일한 조건에서 노멀전기검층을 시물레이션하여 지표 및 지하수 수위가 노멀전기검층에 미치는 영향을 분석하였다. 수치 모델링은 2차원 목표지향 자기적응 고차 hp 유한요소법(2D goal-oriented high-order self-adaptive hp finite element method)을 이용하였다(여기서 h는 요소의 크기, p는 노드에서의 근사 차수). 이 알고리듬을 이용하여 측정한 겉보기비저항의 오차가 1%보다 작도록 계산할 수 있는 최적 hp 격자를 구성함으로써 매우 정밀한 결과를 얻었다. 수치실험결과, 지표부근에서 취득한 노멀전기검층 자료는 기준점전위전극이 시추공에 가까울수록 자료의 왜곡이 증가하며 장노멀전기검층에서의 왜곡이 단노멀전기검층에서 보다 심함을 알 수 있었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2010년도 춘계학술대회 논문집
• /
• pp.49-49
• /
• 2010

The most commonly used numerical modelling techniques for acoustics and vibration are based on element based techniques, such as the nite element and boundary element method. Due to the huge computational eorts involved, the use of these deterministic techniques is practically restricted to low-frequency applications. For high-frequency modelling, probabilistic techniques such as SEA are well established. However, there is still a wide mid-frequency range, for which no adequate and mature prediction techniques are available. In this frequency range, the computational eorts of conventional element based techniques become prohibitively large, while the basic assumptions of the probabilistic techniques are not yet valid. In recent years, a vast amount of research has been initiated in a quest for an adequate solution for the current midfrequency problem. One family of research methods focuses on novel deterministic approaches with an enhanced convergence rate and computational eciency compared to the conventional element based methods in order to shift the practical frequency limitation towards the mid-frequency range. Amongst those techniques, a wave based prediction technique using an indirect Tretz approach is being developed at the K.U.Leuven - Noise and Vibration Research group. This paper starts with an outline of the major features of the mid-frequency modelling challenge and provides a short overview of the current research activities in response to this challenge. Next, the basic concepts of the wave based technique and its hybrid coupling with nite element schemes are described. Various validations on two- and threedimensional acoustic, elastic, poro-elastic and vibro-acoustic examples are given to illustrate the potential of the method and its benecial performance as compared to conventional element based methods. A closing part shares some views on the open issues and future research directions.

• 한국수산과학회지
• /
• 제34권1호
• /
• pp.43-50
• /
• 2001

규칙파, 불규칙파 및 파랑과 흐름이 공존하는 상태에서 프레임에 우리형 그물을 부착하여 구성되어 있는 가두리 시설의 운동특성을 분석하기 위하여 정사각형 및 원형 구조의 가두리 시설을 대상으로 예인 수조에서 수리 모형실험을 실시하였으며, 규칙파중 운동 특성은 선형 포텐셜 이론에 의한 수치 해석의 그것과 비교하였다. 그 결과는 다음과 같이 요약할 수 있다. 1) 규칙파중 모형 가두리 시설의 상하 및 종 동요는 전후 동요와는 달리 그물의 영향을 거의 받지 않았으므로 이 시설물의운동 특성중 가장 중요한 상하 동요를 해석하는 경우에는 그물을 제외하고 프레임만을 고려해도 된다는 것을 확인하였다. 2) 불규칙파중 및 파랑과 흐름이 공존하는 상태에서 모형 가두리 시설의 운동 특성은 입사파 주기의 2배 되는 고주파수에서 시설물의 고유 주기 등에 의해 동적 운동의 peak frequency가 나타남으로써 비선형 즉, 2nd order harmonic 성분이 존재하였다 3) 파동 및 흐름장에서 동요 특성이 정사각형에 비해 비교적 작게 나타난 원형이 파도, 조류 등 환경 조건이 거친 해역에 보다 적합한 것으로 판단되었다.

• 대한조선학회논문집
• /
• 제50권3호
• /
• pp.190-198
• /
• 2013

In order to predict acoustic pressure distributions by exterior incident wave at Cylindrical Hydrophone Array (CHA) sensor's positions, acoustic pressure analysis is performed by using beam tracing method. Beam tracing method is well-known of reliable pressure analysis methods at high-frequency range. When an acoustic noise source is located at the center of rectangular room, acoustic pressure analysis is performed by using both beam tracing method and Power Flow Boundary Element Method (PFBEM). By comparing with results of beam tracing method and those of PFBEM, the accuracy of beam tracing method is verified. We develop the CHA pressure analysis program by verified beam tracing method. The developed software is composed of model input, sensor array creator, analysis option, solver and post-processor. We can choose a model option of 2D or 3D. The sensor array generator is connected to a sonar which is composed of center position, bottom, top and angle between sensors. We also can choose an analysis option such as analysis frequency, beam number, reflect number, etc. The solver module calculates the ray paths, acoustic pressure and result of generating beams. We apply the program to 2D and 3D CHA models, and their results are reliable.

• Structural Engineering and Mechanics
• /
• 제50권2호
• /
• pp.151-161
• /
• 2014

In this paper, fuel tank of the locomotive ER 24 has been studied. Firstly the behavior of fuel and air during the braking time has been investigated by using a two-phase model. Then, the distribution of pressure on the surface of baffles caused by sloshing has been extracted. Also, the fuel tank has been modeled and analyzed using Finite Element Method (FEM) considering loading conditions suggested by the DIN EN 12663 standard and real boundary conditions. In each loading condition, high stressed areas have been identified. By comparing the distribution of pressure caused by sloshing phenomena and suggested loading conditions, optimization of the tank has been taken into consideration. Moreover, internal baffles have been investigated and by modifying their geometric properties, search of the design space has been done to reach the optimal tank. Then, in order to reduce the mass and manufacturing cost of the fuel tank, Non-dominated Sorting Genetic Algorithm (NSGA-II) and Artificial Neural Networks (ANNs) have been employed. It is shown that compared to the primary design, the optimized fuel tank not only provides the safety conditions, but also reduces mass and manufacturing cost by %39 and %73, respectively.

• 한국전기전자재료학회논문지
• /
• 제22권5호
• /
• pp.436-442
• /
• 2009

This paper describes a study on the design of compact polymer bushing with inner control shield. In the bushing, a high electric stress occurred between field shaper and central conductor by the closely space. Also coaxial cylindrical shield has a great height along the axis to control an electric field. Consequently, all the potentials are raised axially along the field shaper and electric stress is concentrated on a part of the surface of the FRP tube near the upper end of the field shaper. In accordance, the field control can be achieved by means of the designs of such inner control shields. The floating and ring shield designs was decreased electric field concentration at critical parts of the bushing. The shield gaps is formed between field shaper and ring shield. Accordance equipotential lines extend through gaps. As a result, the resulting electrical stress are thus reduced in the range $17{\sim}23%$ in the bushing with floating and ring shield designs. Maxwell 2D simulator based on the boundary element method was also introduced in order to verify the reliability of the polymer bushing. The optimized design uses internal elements for electric stress grading at critical parts of the bushing.

• Structural Engineering and Mechanics
• /
• 제68권2호
• /
• pp.227-235
• /
• 2018

Cables are the main load-bearing members of prestressed structure and other tensegrity structures. Based on the static equilibrium principle, a new cable force identification method considering cable flexural rigidity is proposed. Its computational formula is derived and the strategy to solve its implicit formula is introduced as well. In order to improve the reliability and practicality of this method, the influence of the cable flexural rigidity on cable force identification accuracy is also investigated. Through cable force identification experiments, the relationships among certain parameters including jacking force, jacking displacement, initial cable force, and sectional area (flexural rigidity) are studied. The results show that the cable force calculated by the proposed method considering flexural rigidity is in good agreement with the finite element results and experimental results. The proposed method with high computational accuracy and resolution efficiency can avoid the influences of the boundary condition and the length of the cable on calculation accuracy and is proven to be conveniently applied to cable force identification in practice.

• 한국산학기술학회논문지
• /
• 제18권10호
• /
• pp.817-822
• /
• 2017

제동 장치는 기계장치의 사용자나 시스템의 안전관점에서 가장 중요한 요소 중 하나이며, 작동 조건 내에서 신뢰성 있는 제동력이 유지 되어야 한다. 일반적으로 브레이크는 운동에너지를 마찰을 통해 열에너지로 변환하여 회전하는 기계장치를 제동한다. 운동에너지가 열에너지로 전환되는 과정에서 고온의 열이 발생하여 기계적 거동에 영향을 준다. 마찰열은 브레이크 시스템의 열팽창 및 마찰계수 변화 등에 영향을 주고 제어되지 않는 고온은 브레이크 성능을 저하시킨다. 따라서 브레이크의 발열을 예측하고 이를 제어하는 것은 중요하다. 마찰열을 예측하기 위한 다양한 수치해석 연구들이 수행되었지만, 계산의 효율 및 재원의 한계로 수치해석의 경계조건을 다양한 형태로 가정하여 마찰열 예측 연구를 수행하였다. 가정된 마찰열 거동은 실제 열전달 온도 분포 경황과 차이가 있고 이를 이용한 냉각 효과나 열응력 수치해석 결과의 신뢰성이 부족하다. 이러한 한계점을 극복하고 마찰열 예측 시뮬레이션 절차를 정립하기 위하여 본 연구에서는 열-구조 결합 요소를 사용하여 브레이크 시스템의 마찰열 발생을 직접적으로 모사하는 시뮬레이션을 수행하였다. 본 논문은 Finite Element Method(FEM)을 이용하여 브레이크 작동에 따른 마찰열 발생을 모사하고 열분포 특성을 분석하기 위해 브레이크 모델을 대상으로 열-구조 연성요소를 적용한 수치해석 연구를 수행하였다. 이 연구는 마찰열 직접 모사의 필요성을 제안하고 시뮬레이션에 필요한 정보를 제공할 수 있다 판단된다.

• Smart Structures and Systems
• /
• 제20권4호
• /
• pp.427-440
• /
• 2017

One of the suitable structural damage detection methods using vibrational characteristics are damage-index-based methods. In this study, a damage index for identifying damages in plate structures using frequency response function (FRF) data has been provided. One of the significant challenges of identifying the damages in plate structures is high number of degrees of freedom resulting in decreased damage identifying accuracy. On the other hand, FRF data are of high volume and this dramatically decreases the computing speed and increases the memory necessary to store the data, which makes the use of this method difficult. In this study, FRF data are compressed using two-dimensional principal component analysis (2D-PCA), and then converted into damage index vectors. The damage indices, each of which represents a specific condition of intact or damaged structures are stored in a database. After computing damage index of structure with unknown damage and using algorithm of lookup tables, the structural damage including the severity and location of the damage will be identified. In this study, damage detection accuracy using the proposed damage index in square-shaped structural plates with dimensions of 3, 7 and 10 meters and with boundary conditions of four simply supported edges (4S), three clamped edges (3C), and four clamped edges (4C) under various single and multiple-element damage scenarios have been studied. Furthermore, in order to model uncertainties of measurement, insensitivity of this method to noises in the data measured by applying values of 5, 10, 15 and 20 percent of normal Gaussian noise to FRF values is discussed.