• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.133-138
• /
• 2010

This paper describes on aerodynamic characteristics of pantograph system for Next generation high speed train(HEMU-400). The pantograph which supports electric power is located on the roof. Because of this, it generate high drag, severe acoustic noise and vibration which induced unstable flow due to complex configuration. Therefore, the design of high efficient pantograph needs to increase operational speed. In this research, wind tunnel tests were performed to design a high efficient pantograph system using 1/4 scaled model which were KTX-II pantograph, single arm pantograph and periscope type pantograph with square cylinder shape panhead and optimized shape panhead. For real operational condition, flow directions were adapted by rotation of pantograph. From this results of wind tunnel, it is checked that the pantograph with optimized panhead and single arm type or periscope type has better aerodynamic performance. In addition, lift control device and spoiler in pantograph were tested to investigate the validity of application.

• 대한조선학회논문집
• /
• 제50권5호
• /
• pp.324-333
• /
• 2013

Recently, rudder erosion due to cavitation has been frequently reported on a semi-spade rudder of a high-speed large ship. This problem raises economic and safety issues when operating ships. The semi-spade rudders have a gap between the horn/pintle and the movable wing part. Due to this gap, a discontinuous surface, cavitation phenomenon arises and results in unresolved problems such as rudder erosion. In this study, we made a rudder model for 2-D experiments using the NACA0020 and also manufactured gap flow blocking devices to insert to the gap of the model. In order to study the gap flow characteristics at various rudder deflection angles($5^{\circ}$, $10^{\circ}$, $35^{\circ}$) and the effect of the gap flow blocking devices, we carried out the velocity measurements using PIV(Particle Image Velocimetry) techniques and cavitation observation using high speed camera in Seoul National University cavitation tunnel. To observe the gap cavitation on a semi-spade rudder, we slowly lowered the inside pressure of the cavitation tunnel until cavitation occurred near the gap and then captured it using high-speed camera with the frame rate of 4300 fps(frame per second). During this procedure, cavitation numbers and the generated location were recorded, and these experimental data were compared with CFD results calculated by commercial code, Fluent. When we use gap flow blocking device to block the gap, it showed a different flow character compared with previous observation without the device. With the device blocking the gap, the flow velocity increases on the suction side, while it decreases on the pressure side. Therefore, we can conclude that the gap flow blocking device results in a high lift-force effect. And we can also observe that the cavitation inception is delayed.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2000년도 제14회 학술강연논문집
• /
• pp.18-18
• /
• 2000

In the high lift devices specifications for surface smoothness requirements, as manufacturing tolerances, arise out of aerodynamic consideration to minimize drag. True optimization of tolerances is a multi-disciplinary problem involving fluid mechanics, device performance, manufacturing philosophy and life cycle costing. One of the reasons for degradation of wetted surface is discrete roughness as a consequence of manufacturing defects, collectively termed as one of the excrescences effect. Usually, excrescence drag arising out of discrete roughness is of considerable lower order of magnitude as compared to the total drag of the flight bodies. Nor was there adequate predicting tool to account for the extent of drag degradation. Estimation of excrescence drag remained as a state-of-the art based on experimental results.

• 대한기계학회논문집B
• /
• 제30권10호
• /
• pp.1012-1018
• /
• 2006

To evaluate the aerodynamic efficiency of TR-S4 configuration, wind tunnel tests of 40% scaled model were done in KARI LSWT. TR-S4 configuration has different nacelle shape, larger EO/IR camera and aftward wing location compared with TR-S2. Component build-up test after adding each element of model is performed. Also effects of horizontal tail incidences, Flaperon and Aileron deflection. on aerodynamic characteristics are measured. Test results showed that TR-S4 configuration has favorable stability characteristics in longitudinal, lateral and directional for the pitch and yaw motions.

• 한국전기전자재료학회논문지
• /
• 제18권11호
• /
• pp.1014-1018
• /
• 2005

The purpose of this study is to obtain strong bond strength at the interface between piezoelectric substrates and semiconductor thin films to be applied for the manufacture of high-performance acoustic wave semiconductor coupled device. For this purpose, we have compared and examined the effects of different surface treatment methods on hydrophile properties at the surface of the piezoelectric substrates. Moreover, we have observed the effect of microwave and laser on the elimination of water molecules at the interface. As for the piezoelectric substrates, dry method for surface treatment was found to be superior in the control of hydrophilicity of the surface compared to wet method. On the other hand, both microwave and laser were found to be effective in the elimination of water molecules in the interface.

• EDISON SW 활용 경진대회 논문집
• /
• 제6회(2016년)
• /
• pp.58-62
• /
• 2016

본 연구에서는 지면효과의 영향을 비행체의 형상에 따라 비교하기 위해 에어포일, 플랩을 장착한 에어포일 그리고 플라잉디스크를 EDISON_CFD를 통해 해석하고자 한다. 받음각 $0^{\circ}$, $5^{\circ}$, $10^{\circ}$에 대하여 마하수 0.18, 단위 길이 당 레이놀즈수 $3.78{\times}10^{-5}/m$의 유동조건에서 2차원 범용 소프트웨어인 KFLOW_EDISION_13의 S-A Turbulent Model을 이용하여 지면과의 높이를 형상 코드길이를 기준으로 0.25c, 0.5c, 1c, 3c로 변경하면서 해석을 수행하였다. 그 결과 세 형상 모두 일반적인 지면효과인 지면과 가까울수록 양력계수는 증가, 항력계수는 감소하여 양항비가 증가하는 경향을 보여주었다. 하지만 일부 예외적인 부분을 확인하여 분석을 실시하였다.

• 한국전기전자재료학회논문지
• /
• 제13권8호
• /
• pp.643-650
• /
• 2000

Density-of-states effective mass(m*$_{d}$) and conductivity mass(m*$_{c}$)for Ge and Ge$_{0.8}$/Sn$_{0.2}$ are obtained by using 8$\times$8 k.p and strain Hamiltonians. It is shown that m*$_{d}$ and m*$_{c}$ for electrons in Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) and Ge$_{0.8}$/Sn$_{0.2}$/Ge(001) are much smaller than those for electrons in relaxed Ge mainly due to the increase of interaction caused by the strain between the conduction band and valence bands at the $\Gamma$ point. The lift of degeneracy in Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) and Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) makes m*$_{d}$ and m*$_{c}$ for holes smaller than those in relaxed Ge and results in the decrease of the interband scattering as well as interband scattering. The decrease of the interband scattering is more obvious in Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) because of its large splitting energy between the heavy hole and light hole band. Therefore, Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) is expected to be good candidate for the development of ultra high-speed CMOS device.CMOS device.eed CMOS device.CMOS device.

• 한국정밀공학회지
• /
• 제23권4호
• /
• pp.132-138
• /
• 2006

A tape feeder is an important part to supply a micro chip such as 1005 and 0603 components in SMT process. Traditional sprocket wheel type feeder has several problems such as backlash and indexing errors, low compatibility and confidence. However, it is very difficult to solve such problems due to the inevitable fraction defectives of sprocket wheel. Thus, the object of this works is to develop a linear type high precision tape feeding system using cam-slider mechanism. The proposed cam-slider mechanism is composed of several links and a plate, pneumatic actuator is used to generate linear motion. The proposed mechanism has distinct advantages over the conventional mechanism. It has reduced feeding errors, long lift-cycle, and slim width. As a result, the developed tape feeder using cam-slider mechanism shows special characteristics far high precision feeding for chip-mounters.

• Journal of Ship and Ocean Technology
• /
• 제8권4호
• /
• pp.1-9
• /
• 2004

High lifting devices used for control purposes have received much attention in the marine field. Hydrofoils for supporting the hull, roll stabilizer fins for developing the motion damping performance, rudders for maneuverability are the well-known devices. In the present study, the ability of the rudder with flap to produce high lift was analyzed. The boundary layer control, one of the flow control techniques, was adopted. Especially, to build the blown flap, a typical and representative type of a boundary layer control, a flapped rudder was designed and manufactured so that it could eject the water jet from the gap between the main foil and the flap to the flap surface tangentially. And it was tested in the towing tank. Simultaneously, to know the information about the 2-dimensional flow field, a fin model with similar characteristics as the rudder model applicable for the motion control was made and tested in the cavitation tunnel. In addition, local flow measurements were carried out to obtain physical information, for example, a surface pressure measurement and flow visualization around the flap. And CFD simulation was used to obtain information difficult to collect from the experiment about the 2-dimensional flow.

• Journal of Multimedia Information System
• /
• 제7권2호
• /
• pp.189-196
• /
• 2020

We have developed a device for recording biological data by inserting three electrodes and a needle with an angular velocity sensor into the moth for the purpose of measuring the electromyogram of the flapping and the corresponding lift force. With this measurement, it is possible to evaluate the moth-physiological function of moths, and the amount of pesticides that insects are exposed to (currently LD50-based standards), especially the amount of chronic low-concentration exposure, can be reduced the dose. We measured and recorded 2-channel electromyography (EMG) and angular velocity corresponding to pitch angle (pitch-like angle) associated with wing flapping for 100 sweet potato hawkmoths (50 females and 50 males) with the animals suspended and constrained in air. Overall, the angular velocity and amplitude of EMG signals demonstrated high correlation, with a correlation coefficient of R = 0.792. In contrast, the results of analysis performed on the peak-to-peak (PP) EMG intervals, which correspond to the RR intervals of ECG signals, indicated a correlation between ΔF fluctuation and angular velocity of R = 0.379. Thus, the accuracy of the regression curve was relatively poor. Using a DC amplification circuit without capacitive coupling as the EMG amplification circuit, we confirmed that the baseline changes at the gear change point of wing flapping. The following formula gives the lift provided by the wing: angular velocity × thoracic weight - air resistance - (eddy resistance due to turbulence). In future studies, we plan to attach a micro radio transmitter to the moths to gather data on potential energy, kinetic energy, and displacement during free flight for analysis. Such physiological functional evaluations of moths may alleviate damage to insect health due to repeated exposure to multiple agrochemicals and may lead to significant changes in the toxicity standards, which are currently based on LD50 values.