• JSTS:Journal of Semiconductor Technology and Science
• /
• 제17권3호
• /
• pp.438-445
• /
• 2017

This paper presents a low-power high-resolution band-pass ${\Sigma}{\Delta}$ ADC for accelerometer applications. The proposed band-pass ${\Sigma}{\Delta}$ ADC consists of a high-performance 6-th order feed-forward ${\Sigma}{\Delta}$ modulator with 1-bit quantization and a low-power, area-efficient digital filter. The ADC is fabricated in 180 nm 1P6M mixed-signal CMOS process with a die area of $5mm^2$. This high-resolution ADC got 90 dB peak signal to noise plus distortion ratio (SNDR) and 96 dB dynamic range (DR) over 4 kHz bandwidth, while the intermediate frequency (IF) is shifting from 100 KHz to 200 KHz. The power dissipation of the chip is 5.6 mW under 1.8 V (digital)/3.3 V (analog) power supply.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(2)
• /
• pp.491-494
• /
• 2003

This paper presents a new conceptual electromagnetic induction eddy current-based stainless steel plate spiral type heater for heat exchanger or Dual Packs Heater in hot water producer, boiler steamer and super heated steamer, which is more suitable and acceptable for new generation consumer power applications. In addition, all active clamped edge resonant PWM high frequency inverter using trench gate IGBTs power module can operate under a principle oi zero voltage soft communication with PWM is developed and demonstrated for a high efficient Induction heated hot water producer and boiler in the consumer power applications. This consumer induction heater power appliance using active clamp soft switching PWM high frequency inverter is evaluated and discussed on the basis of the simulation and experimental results.

• 전력전자학회논문지
• /
• 제20권4호
• /
• pp.337-343
• /
• 2015

The multi-level inverters are highly efficient for high-power and medium-voltage AC driving applications, such as high-speed railway systems and renewable energy resources, because such inverters generate lower total harmonic distortion (THD) and electromagnetic interface (EMI). Lower switching stress occurs on switching devices compared with conventional two-level inverters. Depending on the multi-level inverter topology, the required components and number of switching devices are different, influencing the overall efficiency. Comparative studies of multi-level inverters based on loss analysis and output characteristic are necessary to apply multi-level inverters in high-power AC conversion systems. This paper proposes a theoretical loss analysis method based on piecewise linearization of characteristic curves of power semiconductor devices as well as loss analysis and output performance comparison of five-level neutral-point clamped, flying capacitor inverters, and high-level cascaded H-bridge multi-level inverters.

• Journal of Communications and Networks
• /
• 제8권1호
• /
• pp.1-7
• /
• 2006

Quadrature amplitude modulation-spread spectrum (QAM-SS) and code division multiplexing (CDM) are multi-level modulation schemes with high performance but they cause a large peak-average power ratio (PAPR). Therefore, this paper proposes a novel modulation scheme for high-rate transmission which follows a sequence of CDM-mapping-CDM not only to correct the above-mentioned problem but also offer a high flexibility in obtaining arbitrary multilevel modulation with very low implementation complexity and high performance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2152-2154
• /
• 1999

In this paper, we suggested the design rule of high-voltage rectangular waveform generator working in low frequency domain (5Hz $\sim$ 60Hz). Most of the commonly used power electronic switching devices have voltage ratings up to several kV. So it is difficult to design and fabricate high-voltage switching systems with the power electronic devices alone. We have combined IGBTC(1200V, 50A) with the specially designed transformer to get the high-voltage rectangular waveforms up to 40kV. In this work. next two things are the main factors. The first one is design of transformer working low-frequency domain close to 5Hz. And the second one is additional voltage source to floating the transformer voltage output. As a result, we can get frequency-variable and high-voltage rectangular voltage waveform and this can be a more efficient power source of sandpaper manufacturing process.

• 한국통신학회논문지
• /
• 제22권4호
• /
• pp.696-705
• /
• 1997

This paper presents an efficient adaptive predistortion technique compensating linear and nonlinear distortions caused by high-power amplifier (HPA) with memory in OFDM systems. The efficient adaptive data predistortion techniques proposed for compensation of HPA with memory in single carrier systems cannot be applied to OFDM systems since the possible input levels for HPA is infinite in OFDM systems. Also, previous adaptive predistortion techniques, based on Volterra series modeling, are not suitable for real-time implementation due to high computational burden and slow convergence rate. In the proposed approach, the memoryless HPA preceded by a linear filter in OFDM systems is modeled by the Wiener system which is then precompensated by the proposed adaptive predistorter with a minimum number of filter taps. An adaptive algorithm for adjusting the proposed adaptive predistorter is derived using the stochastic gradient method. It is demonstrated by computer simulation that the performance of OFDM system suffering from nonlinear distortion can be greatly improved by the proposed efficient adaptive predistorter using a small number of filter taps.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 A
• /
• pp.795-797
• /
• 2005

This paper describes a measurement & verification scheme for the high efferent lighting program in Demand Side Management (DSM), which was Introduced in the beginning of the 1980's in Korea With the dramatic changes in the circumstance of power industry in Korea. It is required the reviewing for the existing process of DSM programs and the development of the new process methods/standards on the evaluation of DSM programs. To design an accurate evaluation scheme for the high efficient lighting program. In this paper, we develop an evaluation prototype for the high efficient lighting program using measurements and stipulated factors. The proposed scheme is tested by practical measurements and modified stipulated factors Results from the case studios show the proposed scheme could provide the practical performance evaluation results with promising accuracy.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 1999년도 학술대회논문집-국제 전기방전 및 플라즈마 심포지엄 Proceedings of 1999 KIIEE Annual Conference-International Symposium of Electrical Discharge and Plasma
• /
• pp.162-167
• /
• 1999

In Auxiliary block of High speed train Power factor correction and Harmonics reduction is very important issue for efficient energy transport. The GTO-equipped PWM converter is used for traction untill resently. but the rising power capability of IGBTs resently allows to build IGBT-equipped PWM converter with a considerably increases switching frequency. In this paper presents switching pattern, control method, operation mode and tuned filter to reduce dc link voltage ripple for paralleled converter.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권5호
• /
• pp.549-556
• /
• 2014

This paper proposes a highly power-efficient single-inductor multiple-outputs (SIMO) DC-DC converter with a gate charge sharing method in which gate charges of output switches are shared to improve the power efficiency and to reduce the switching power loss. The proposed converter was fabricated by using a $0.18{\mu}m$ CMOS process technology with high voltage devices of 5 V. The input voltage range of the converter is from 2.8 V to 4.2 V, which is based on a single cell lithium-ion battery, and the output voltages are 1.0 V, 1.2 V, 1.8 V, 2.5 V, and 3.3 V. Using the proposed gate charge sharing method, the maximum power efficiency is measured to be 87.2% at the total output current of 450 mA. The measured power efficiency improved by 2.1% compared with that of the SIMO DC-DC converter without the proposed gate charge sharing method.

• Journal of Power Electronics
• /
• 제18권4호
• /
• pp.985-996
• /
• 2018

The implementation and performance evaluation of an interleaved boundary conduction mode (BCM) boost power factor correction (PFC) converter is presented in this paper by employing three wide band-gap switching devices: a super junction silicon (Si) MOSFET, a silicon carbide (SiC) MOSFET and a gallium nitride (GaN) high electron mobility transistor (HEMT). The practical considerations for adopting wide band-gap switching devices to BCM boost PFC converters are also addressed. These considerations include the gate drive circuit design and the PCB layout technique for the reliable and efficient operation of a GaN HEMT. In this paper it will be shown that the GaN HEMT exhibits the superior switching characteristics and pronounces its merits at high-frequency operations. The efficiency improvement with the GaN HEMT and its application potentials for high power density/low profile BCM boost PFC converters are demonstrated.