• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.6
• /
• pp.896-902
• /
• 2009

EGR is applied in order to lower temperature of combustion chamber by using the specific heat of carbon dioxide in engine exhaust gas. However, the problem of EGR system in diesel engine is high PM concentration. Combined EGR system can be reduced it by mixing exhaust gas of gas engine into the intake air of diesel engine. This experimental study was designed for EGR system for both engines use. The results of EGR experimental study by using diesel engine and gas engine are as follows. 1) The pressure of combustion and rate of heat release decreased. 2) The specific fuel consumption increased. But, up to middle load, it little increased. 3) NO concentration has decreased up to 50% in almost all combustion area. 4) The variation of the PM concentration at low load is not so seen. But at high load, PM increased rapidly when concentration of oxygen is decreased and most of it caused the increasing of Dry Soot.

• Corrosion Science and Technology
• /
• v.19 no.6
• /
• pp.281-287
• /
• 2020

Chloride ion is one of the most important corrosive agents in atmospheric corrosion, especially in marine environments. It has high adsorption rate and increases the conductivity of electrolytes. Since chloride ions affect the protective properties and the surface composition of the corrosion product, they increase the corrosion rate. A low level of chloride ions leads to uniform corrosion, whereas a high level of chloride ions may induce localized corrosion. However, higher solution temperatures tend to increase the corrosion rate by enhancing the migration of oxygen in the solution. This work focused on the effect of NaCl concentration and temperature on galvanic corrosion between A516Gr.55 carbon steel and AA7075T6 aluminum alloys. When AA7075T6 aluminum alloy was galvanically coupled to A516Gr.55 carbon steel, AA7075T6 was severely corroded regardless of NaCl concentration and solution temperature, unlike the corrosion properties of single specimen. The combined effect of surface treatment involving carbon steel and aluminum alloy on corrosion behavior was also discussed.

• Journal of the Korean Society of Safety
• /
• v.26 no.2
• /
• pp.42-47
• /
• 2011

Going underwater is supposed to begin with the history of human beings. At first it was confined to relatively shallow level, less than several meters by holding breath. Recently, deep level diving has been necessary for such purpose as construction, maritime salvage, military operations, research and sports by using SCUBA(self-contained underwater breathing apparatus) equipment. As one goes down into water, the pressure on the diver is increased due to water pressure with depth, usually 1 atm for each 10 m water level. In deep water, mixed gas or nitrox(EAN, enriched air nitrox) could be applied for the divers lest they should get disease due to high pressure. Of these, the former is usually composed of oxygen and inert gas like helium or hydrogen, the latter contains higher oxygen content than that in normal air in which the oxygen concentration is designated by the character "EAN" followed by vol. % of oxygen, for example, "EAN 40" contains 40% of oxygen. In this case, a victim was found at the 39 m below the sea surface breathing air and nitrox in cylinder wrongly marked as EAN 36, which was analyzed to contain 63% of oxygen by GC/TCD. The cause of death could not be exactly related with the oxygen content in the nitrox cylinder, because the accurate depth for the victim to dive was not known, even though the victim was just found at the depth of 39 m. However, the wrongly marked nitrox could be believed to be the main cause of the death at the depth unless there happened any other accident except that during diving.

• Journal of Microbiology and Biotechnology
• /
• v.19 no.6
• /
• pp.596-603
• /
• 2009

This study aimed to examine the influence of adding an oxygen vector, n-dodecane, on hyaluronic acid (HA) production by batch culture of Streptococcus zooepidemicus. Owing to the high viscosity of culture broth, microbial HA production during 8-16 h was limited by the oxygen transfer coefficient $K_La$, which could be enhanced by adding n-dodecane. With the addition of n-dodecane to the culture medium to a final concentration of 5% (v/v), the average value of $K_La$ during 8-16 h was increased to $36{\pm}2h^{-1}$, which was 3.6 times that of the control without n-dodecane addition. With the increased $K_La$ and dissolved oxygen (DO) by adding 5% (v/v) of n-dodecane, a 30% increase of HA production was observed compared with the control. Furthermore, the comparison of the oxygen mass transfer in the absence and presence of n-dodecane was conducted with two proposed mathematical models. The use of n-dodecane as an oxygen vector, as described in this paper, provides an efficient alternative for the optimization of other aerobic biopolymer productions, where $K_La$ is usually a limiting factor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.9
• /
• pp.775-782
• /
• 2003

In the study, the total conductivies in [(Ce $O_2$)$_{1-x}$ (Zr $O_2$)$_{x}$]$_{0.8}$(Sm $O_{1.5}$)$_{0.2}$ (x- 0, 0.05, 0.1, 0.2) solid solution were measured as a function of temperature and oxygen partial pressure between 80$0^{\circ}C$ and 1,00$0^{\circ}C$ using 4-probe d.c method. Under pure oxygen atmospere, the oxygen ionic conductivity of [(Ce $O_2$)$_{1-x}$ (Zr $O_2$)$_{x}$]$_{0.8}$(Sm $O_{1.5}$)$_{0.2}$ decreased with the concentration of Zr $O_2$At high oxygen partial pressure, the electrical conductivity is almost independent of oxygen partial pressure and decreased with the increase in Zr content. However, the electrical conductivity increase with decreasing oxygen partial pressure and is almost independent of Zr content at low oxygen partial pressure. Empirically, Total conductivity( $\sigma$ ) was expressed by the p$o_{2}$ -independent conductivity as $\sigma$$_{i}$, and the $p_{-1/4}$ $o_{2}$sup -dependent part as $\sigma$$_{e}$. Total, ionic and electronic conductivities fitted by data enabled to determine the transference number. The ionic transference number( $t_{i}$ ) decreased while the electronic transference( $t_{e}$ ) increase with the increase in Zr content and p$o_{2}$.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.6 no.3
• /
• pp.189-193
• /
• 2001

Critical cell density (CCD), the maximum cell concentration without mutual shading in algal cultures, can be used as a new operating parameter for high-density algal cultures and for the application of the flashing light effect on illuminated algal cultures. CCD is a function of average cell volume and light illumination area. The CCD is thus proposed as an index of estimation of mutual shading in algal cultures. Where cell densities are below the CCD, all the cells in photobioreactors can undergo photosysnthesis at their maximum rate. At cell densities over CCD, mutual shading will occur and some cells in the illumination chamber cannot grow photoautotrophically. When the cell concentration is higher than the CCD, specific oxygen production rates under flashing light were higher than those under continuous light. The CCD was found to be a useful engineering parameter for the application of flashing light, particularly in high-density algal cultures.

• Korean Journal of Crystallography
• /
• v.11 no.3
• /
• pp.151-156
• /
• 2000

Yb/YAG single crystals were grown from the melt composition of Y/sub 1-x/Yb/sub x/)₃Al/sub 5/O/sub 12/ where x equal to 5, 10, 15, 20, 25, 33, 50, 75 and 100 at % by floating zone method. Optimum growth parameters to get high quality single crystals were 3.5 mm/h of growth rate and 20 rpm of rotation rate under the N₂ atmosphere. After the growth, color of crystals was appeared with pale blue due to the lack of oxygen, but it was disappeared after annealing at 1450℃ for 2 hr. Absorption coefficients were linearly increased depending on the concentration of Yb/sup 3+/ ions. Broad emission band was measured in the range of 1020 to 1050 nm with the peak intensity at 1031 nm and 1051 nm because of ²F/sub 5/2/(1)→²F/sub 7/2/(3) and ²F/sub 5/2/(1)→²F/sub 7/2/(4) transition respectively. When Yb/sup 3+/ ions were substituted with high rates, there were tendency to decrease the measured fluorescent lifetime for Yb ions depending on the concentration of Yb/sup 3+/ ions.

• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.373-378
• /
• 2000

The crevice corrosion of local corrosion occur when the gap exist on metal surface. This crevice corrosion happen to region such as flange of pipe, contact part of casing, under gasket and packing, between valve disk and seat of pump etc. Especially The crevice corrosion of mild steel(SS 400) get serious. This paper was studied on the crevice corrosion of SS 400 in fluid environment. In $0\%,\;2\%,\;3.5\%,\;5\% NaCl$ solution, the aspect of the crevice corrosion and polarization behavior under the crevice corrosion was investigated. And Weight loss rate of SS 400 with crevice and non-crevice was measured according to the NaCl concentration. The main results obtained are as follows : 1) Under crevice corrosion, the corrosion potential become less noble as the concentration of NaCl solution increased. 2) The current density under open circuit potential was high drained as concentration of NaCl solution increased by $3.5\%$ but the concentration increased over $3.5\%$, the current density was low drained. 3) The weight loss rate of SS 400 was increased as concentration of NaCl solution Increased by $3.5\%$, but the concentration increased over $3.5\%$, that of SS 400 was decreased. 4) Effect of oxygen for crevice corrosion in the concentration of $3.5\%$ NaCl solution become sensitive than that $0\%$ NaCl solution.

• Corrosion Science and Technology
• /
• v.15 no.3
• /
• pp.129-134
• /
• 2016

The effects of Ti on the high temperature oxidation of Ni-based superalloys were investigated by cyclic oxidation at $850^{\circ}C$ and $1000^{\circ}C$. The oxide scale formed at $850^{\circ}C$ consists of $Cr_2O_3$, $Al_2O_3$, and $NiCr_2O_4$ layers, while a continuous $Al_2O_3$ layer was formed at $1000^{\circ}C$. The oxidation rate of the alloy with higher Ti content was higher than the alloy with less Ti content at $850^{\circ}C$, possibly due to the increase in the metal vacancy concentration in the $Cr_2O_3$ layer involved by incorporation of $Ti^{4+}$. However, Ti improved the oxidation resistance of the superalloy at $1000^{\circ}C$ by reducing oxygen vacancy concentration in $Al_2O_3$ layer.

• Journal of Microbiology and Biotechnology
• /
• v.16 no.3
• /
• pp.469-474
• /
• 2006

Partial nitrification blocking of the oxidation of nitrite ($NO_{2}^{-}$) to nitrate ($NO_{3}^{-}$) has cost-efficient advantages such as lower oxygen and organics demand for nitrification and denitrification, respectively. A nitrifying membrane bioreactor of submerged type was operated for the treatment of synthetic ammonium wastewater with the purpose of nitrite build-up without affecting the efficiency of ammonium oxidation. A high ammonium concentration (1,000 mg/l) was completely converted to nitrate at up to 2 kg $N/m^3$ day under sufficient aeration. The control of pH under sufficient aeration was not a reliable strategy to maintain stable nitrite build-up. When the dissolved oxygen concentration was kept at 0.2-0.4 mg/l by adjusting the aeration rate, about 70% of nitrite content was obtained with ammonium oxidation efficiency higher than 93%. The increase of suction pressure due to membrane fouling was not significant under lowered aerating environment over a 6-month period of operation. The composition of nitrifier community, including relative abundance of nitrite oxidizers in a nitrite-accumulating condition, was quantified by fluorescence in situ hybridization analysis.