• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.11a
• /
• pp.119-120
• /
• 2011

Recently, the effects of high temperature and fiber content on the residual mechnical properties of high-strength concrete were experimentally investigated. In this paper, residual mechanical properties of concrete with water to cement (w/c) ratios of 55%, 42% and 32% exposed to high temperature are compared with those obtained in fiber reinforced concretes of similar characteristics with the ranging of 0,05% to 0,20% polypropylene (PP) fibers by volume of concrete, and considered factors include pre-load levels (20% and 40% of the maximum load at room temperature). Outbreak time and water contents were tested and were determined the compressive strength. In the result, it is showed that to prevent the explosive spalling of 50MPa grade concretes exposed to high temperature need more than 0.05Vol.% PP fibers. Also, the cross-sectional area of PP fiber can influence on the residual mechanical properties and the spalling tendency of fiber reinforced concrete exposed to high temperature. Especially, the external loading increases not only the residual mechanical properties of concrete but also the risk of spalling and the brittle tendency.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.145-146
• /
• 2023

In this study, the effect of hybrid fiber reinforcement on the residual strength and impact resistance of high-strength cementitious composites exposed to high temperatures was investigated. A cementitious composites was manufactured in which 0.15 vol% of polypropylene fiber (PP) and 1.0 vol% of smooth steel fiber (SSF) were double-mixed, and a residual strength test was conducted while thermal stress was applied by heating test, and then a high-velocity impact test was performed. In the case of general cementitious composites, the rear surface is damaged due to explosion and low tensile strength during high temperature or impact, while hybrid fiber reinforced cementitious composites can repeatedly absorb and distribute stress until multiple fibers are damaged to suppress the propagation of impact and resistance to explosion. Therefore, this study analyzed the residual strength of cementitious composites exposed to high temperatures depending on whether hybrid fibers were mixed or not, and collected research data on fracture behavior through high-speed impact tests to evaluate impact resistance and mechanical properties.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.88-91
• /
• 2011

Glass fiber drawing from a silica preform is one of the most important processes in optical fiber manufacturing. High purify silica preform of cylindrical shape is fed into the graphite furnace, and then a very thin glass fiber of 125 micron diameter is drawn from the softened and heated preform. A computational analysis is performed to investigate the heat transfer characteristics of preform heating and the glass fiber drawing in the furnace. In addition to the dominant radiative heating of preform by the heating element in the furnace, present analysis also includes the convective heat transport by the gas flowing around the preform that experiences neck-dawn profile and the freshly drawn glass fiber at high fiber drawing speed. The computational results present the effects of gas flow on the temperature of preform and glass fiber as well as the neck-down profile of preform.

• Advances in concrete construction
• /
• v.8 no.1
• /
• pp.21-31
• /
• 2019

The rich recipe of ultra high performance concrete (UHPC) offers the higher mechanical, durability and dense microstructure property. The variable like cement/sand ratio, amount of supplementary cementitious material, water/binder ratio, amount of fiber etc. alters the UHPC hardened properties to any extent. Therefore, to understand the effects of these variables on the performance of UHPC, inevitably a stage-wise development is required. In the present experimental study, the effect of sand/cement ratio, the addition of finer material (fly ash and quartz powder) and, hybrid fiber on the fresh, compressive and microstructural property of UHPC is evaluated. The experiment is conducted in three phases; the first phase evaluates the flow value and strength attainment of ingredients, the second phase evaluates the efficiency of finer materials (fly ash and quartz powder) to develop the UHPC and the third phase evaluate the effect of hybrid fiber on the flow value and strength of ultra high performance hybrid fiber reinforced concrete (UHP-HFRC). It has been seen that the addition of fly ash improves the flow value and compressive strength of UHPC as compared to quartz powder. Further, the usage of hybrid fiber in fly ash contained matrix decreases the flow value and improves the strength of the UHP-HFRC matrix. The dense interface between matrix and fiber and, a higher amount of calcium silicate hydrate (CSH) in fly ash contained UHP-HFRC is revealed by SEM and XRD respectively. The dense interface (bond between the fiber and the UHPC matrix) and the higher CSH formation are the reason for the improvement in the compressive strength of fly ash based UHP-HFRC. The differential thermal analysis (DTA/TGA) shows the similar type of mass loss pattern, however, the amount of mass loss differs in fly ash and quartz powder contained UHP-HFRC.

• Journal of Animal Science and Technology
• /
• v.65 no.5
• /
• pp.989-1001
• /
• 2023

The study evaluated the effects of dietary fiber and energy levels administered during two growing periods (d 0-28 and d 29-56) for pigs exposed to a high temperature. A total of 96 growing pigs were used in six treatments as: Two treatments in thermoneutral temperature (21℃-24℃) with dietary energy of 3,300 and the inclusion of high or low fiber, two treatments in heat stress (30℃-34℃) with dietary energy of 3,300 and the inclusion of high or low fiber, and two treatments in heat stress with dietary energy of 3,450 and the inclusion of high or low fiber. Among standard energy level treatments, heat-stressed pigs showed lower average daily gain (ADG), feed intake, digestibility of dry matter, gross energy, crude protein, and crude fiber in phases 1 and 2. Moreover, higher concentrations of acetate, propionate, butyrate, and total short-chain fatty acid (SCFA) in feces were shown in pigs fed high fiber diets. There was a negative interaction between dietary fiber and energy for the fecal concentration of isobutyrate in phase 1 and valerate in phase 2. Pigs in heat stress treatments showed a higher rectal temperature, respiratory rate, hair cortisol, plasma zonulin, and fecal lipocalin-2. Among heat stress treatments, the overall ADG was increased in pigs fed high fiber. Pigs fed high dietary fiber showed a greater concentration of acetate, propionate, butyrate, and total SCFA. High fiber treatments decreased plasma zonulin. In conclusion, the inclusion of beet pulp, soluble fiber, at the level of 4% looks necessary in pigs diet during heat stress.

• Korean Journal of Optics and Photonics
• /
• v.19 no.3
• /
• pp.169-174
• /
• 2008

In this paper, we have presented techniques to reduce the splicing loss between standard single mode fiber and high ${\Delta}$ single mode fiber based on the mode expanding and mode evolution induced by thermal treatment of the fibers. The experimental results show that mechanical splicing loss can be reduced from 2.3 dB to 0.1 dB through proper thermal treatment of the high ${\Delta}$ fiber. Meanwhile, we achieved $0.2{\sim}0.4dB$ of low splicing loss between two fibers by heating the splicing region using electric arcing or an oxygen flame.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.6
• /
• pp.551-555
• /
• 2009

We studied the design of fiber optic gyroscope that enables to sense high rotation by extending the limit of rotation sensibility of fiber optic interferometer. Based on the digital serrodyne modulation technique, the signal processing of fiber optic gyroscope was designed and the prototype fiber optic gyroscope showed the high rotation sensibility up to ${\pm}3000[deg/sec]$ and scale factor performance of about 150[ppm] by the experiments. Accordingly, we confirmed that the design of fiber optic gyroscope was valid for high rotation.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.98-99
• /
• 2020

This study is aim to assess mechanical properties which is highly related to structural safe and durability of 100MPa high strength concrete mixed with amorphous metallic fiber. All specimens were heated with low velocity heating rate(1℃/min.), residual compressive strength and residual flexural strength was evaluated. The specimens were cooled down to room temperature after heating. As a result, in the case of 100MPa high-strength concrete, the residual compressive strength enhancing effect of amorphous metallic fiber has showed with the mix proportion of fiber. In addition, residual flexural strength showed more regular pattern before 300℃ then residual compressive strength, but simillar decreasing behavior was shown after 300℃ like residual compressive strength. Further study about fiber pull-out behavior and fiber mechanical, chemical property change due to temperature is needed.

• Preventive Nutrition and Food Science
• /
• v.7 no.1
• /
• pp.78-87
• /
• 2002

This study investigated the production of insoluble dietary fiber using forest waste and the dietary effect of manufactured insoluble fiber on physiological function in rat fed high cholesterol duets. Insoluble dietary fiber was prepared from the wood chips of oak (Quercus mongolica). The best condition for steam-explosion treatment for the preparation of insonuble dietary fiber was 25 kg/cm$^3$pressure for 6 minutes. In the chemical analysis of insoluble dietary fiber pretreated by 1% sodium hydroxide solution with steam-exploded wood, $\alpha$-cellulose content was 61.7% in the insoluble dietary fiber which contained 7.6% residual lignin. In order to compare insoluble dietary fiber with commercial $\alpha$-cellulose of physiological function, Sprague-Dawley male rats weighing 100$\pm$10 g were randomly assigned to one normal diet and five high cholesterol diet containing 1% cholesterol. The high cholesterol diet groups were classified as fiber free diet (FF group), 5% commercial $\alpha$-cellulose diet (5C group), 10% commercial $\alpha$-cellulose (l0C group), 5% insoluble dietary fiber dict (5M group), and 10% insoluble dietary fiber (10M group). The rats were fed ad libidum for 4 weeks. Food intake, weights gain, and food efficiency ratio in high cholesterol groups were higher than those of normal group, but there were no significant differences between the experimental groups. There were not any significant differences in the weights of livers, kidneys and small intestine of insoluble dietary fiber supplemented groups, but weight of cecum in all insolube dietary fiber group were significantly higher than those of FF group. A gstrointestinal transit time was decreased by supplementation of insoluble dietary fiber. Weight and water contents of feces in the insoluble dietary fiber supplemented groups were significantly higher than those of the FF group. There were not any significant differences in the activities of the glutamic pyruvic transaminase (GPT) and glutamic oxaloacetic transaminase (GOT) between the experimental groups. In conclusion, the manufactured insoluble dietary fiber and commercial insoluble fiber have the same physiological effects. The preparation method of the insoluble dietary fiber from the oak chips suited its purpose.

• Journal of Environmental Science International
• /
• v.8 no.4
• /
• pp.473-477
• /
• 1999

The purpose of this study was to investigate the characteristics of removal efficiency for aromatic hydrocarbons using a high-temperature fiber filter on a laboratory scale. The main elemental compositions of a high-temperaure fiber filter are aluminium and silica, which can act as the catalysts. Benzene, toluene and o-xylene among aromatic hydrocarbons were used in this experiment. For 3cm thickness of fiber filter, these compounds were removed more than 90% at the face velocities of 3cm/sec and 5cm/sec above 45$0^{\circ}C$. For 4cm thickness of it, the removal efficiencies of these compounds were almost 90% from 40$0^{\circ}C$ at the same face velocities, suggesting that it may be due to increasing the contact time between the fiber filter and aromatic hydrocarbons. The pressure droop ranged from 22 to 48mmH2O for 3cm thickness of fiber filter. However, for 4cm thickness of it, it was about two times(41~89mm$H_2O$) higher than that for 3cm fiber thickness.