• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.470-474
• /
• 1997

Since the ceramic/metal joints is joined at high temperature, the residual stress will develop during when cooled from bonding temperature due to remarkable difference of thermal expansion coefficient between creamic and metal. Moreover, the edge of jointed interface makes singular stress field in the ceramic/metal joints and this singular stress field much influences on the strength of joints. In this study, The influence of residual stress, mechanical load and repeat thermal sysle was estimated in the ceramic/metal joints. According to this influence, the change of singular stress field was analyed and then strength test, X-ray measurement are performed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.310-315
• /
• 2000

We analyzed thermal stress of the STS VOD ladle by the variation of material property of refractory, and determined the location of back filler using FE analysis. Thermal distribution of refractory of ladle between hot face and back face were decreased by the increasing the thermal conductivity, and thermal stress of refractory were decreased about 2 to 4 times with the decreasing the young's modulus coefficients. Back filler, which is constructed to absorb the thermal expansion of dolomite refractory, has relatively low thermal conductivity. Inner side of refractory of ladle maintained high temperature, but temperature of outer side of ladle decreased low. Consequently, inner expansion and outer contraction were appeared. and thermal stress were increased, so thermal stress by the construction of back filler were increased.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1996년도 가을 학술발표회 논문집
• /
• pp.133-139
• /
• 1996

As construction technology advances, most of civil engineering structures are becoming larger and taller. Therefore, high strength concrete is necessary for them. For high strength concrete, it needs a large amount of unit cement content and low water-cement ratio inevitably, so that a large amount of heat occurs in concrete. The thermal cracks make the durability and quality of concrete structures become worse, result from temperature rise and thermal stress due to heat of hydration. In this study, the proposal of using ground granulated blast furnace slag, fly ash and chemical admixtures was investigated to decrease the temperature rise of concrete.

• 한국강구조학회 논문집
• /
• 제16권4호통권71호
• /
• pp.433-442
• /
• 2004

본 연구는 Eurogode 3 Part 1.3을 근거하여 온도증가에 따른 압축을 받는 냉간성형 C-형강 기둥의 플랜지와 웨브의 탄성국부좌굴 응력 해석 프로그램을 개발하였다. 고온에서 응력-변형률 관계식은 Eurocode 3 Part 1.2를 근거하였다. 온도증가에 따른 압축을 받는 냉간성형 C-형강의 임계온도와 탄성국부좌굴 응력은 본 연구에서 개발한 컴퓨터 프로그램에 의해 해석하였고, 해석 예에 대한 비교 고찰을 하였다.

• Journal of Welding and Joining
• /
• 제14권5호
• /
• pp.95-105
• /
• 1996

Korea Gas Corporation has operated high pressure gas transmission line of about 600 kilometers and, therefore, a series of repair welding processes are required in order to cope with external defects such as dent, gouge, cracking usually due to mechanical attacks. Most of gas pipelines repair processes are performed after completely venting remaining gas. However, in some case, though it is very unusual, repairs require without venting gas. For instance, this case is that damaged pipeline is remedied with split sleeve by welding. In this paper, in an effort to confirm a safe application of the split sleeve welding, residual stress, strain and temperature distributions are evaluated by computer simulation and experiments. The results obtained are as follows : 1) Computer modelling is supposed to be reasonable because microstructure changes due to welding is simulated coincidently as compare to that of real condition. 2) The maximal temperature on inside surface of pipeline is 50$0^{\circ}C$ for the repair welding process. 3) The amount of residual stress is estimated as the stress corresponding to 0.8% strain. 4) The repair process employed is determined to be technically preferable because of its avoiding cracks and fractures in the course of welding.

• 대한기계학회논문집A
• /
• 제31권12호
• /
• pp.1157-1164
• /
• 2007

Ceramic honeycomb structures have performed successfully as catalyst supports for meeting hydrocarbon, carbon monoxide and nitrous emissions standards for gasoline-powered vehicles. Three-way catalyst converter has to withstand high temperature and thermal stress due to pressure fluctuations and vibrations. Thermal stress constitutes a major portion of the total stress which the ceramic catalyst support experiences in service. In this study, temperature distribution was measured at ceramic catalyst supports. Thermal durability was evaluated by power series dynamic fatigue damage model. Radial temperature gradient was higher than axial temperature gradient. Thermal stresses depended on direction of elastic modulus. Axial stresses are higher than tangential stresses. Tangential and axial stresses remained below thermal fatigue threshold in all engine operation ranges.

• Journal of Ecology and Environment
• /
• 제29권5호
• /
• pp.479-484
• /
• 2006

Ecophysiological parameters of non-transgenic sweetpotato (NT) and transgenic sweetpotato (SSA) plants were compared to evaluate their resistance to multiple environmental stresses. Stomatal conductance and transpiration rate in NT plants decreased markedly from Day 6 after water was withheld, whereas those values in SSA plants showed relatively higher level during this period. Osmotic potential in SSA plants was reduced more negatively as leaf water potential decreased from Day 8 after dehydration treatment, while such reduction was not shown in NT plants under water stressed condition. SSA plants showed less membrane damage than in NT plants. As water stress and high light stress, were synchronously applied to NT and SSA plants maximal photochemical efficiency of PS II ($F_v/F_m$) in NT plants markedly decreased, while that in SSA plants was maintained relatively higher level. This trend of changes in $F_v/F_m$ between SSA plants and NT plants was more conspicuous as simultaneously treated with water stress, high light and high temperature stress. These results indicate that SSA plants are more resistive than NT plants to multiple environmental stresses and the enhanced resistive characteristics in SSA plants are based on osmotic adjustment under water stress condition and tolerance of membrane.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권8호
• /
• pp.598-604
• /
• 1999

This paper describes the research to minimize the film stress and maximize the aspect ratio of photoresist structure, especially about SU-8 for electroplating mold. UV LIGA process using SU-8 allows fabricating high aspect ratio polymer structures. However, it is hard to get fine patterns in the high aspect ratio structures because of high internal stress and difficulty of removing SU-8. The purpose of this paper is to setup the process condition for the obtainment of both low film stress and high aspect ratio and to find design rules that make the pattern be less dependent on stress problem. Firstly, the process of heat treatment and exposure of SU-8 are proposed. These two conditions control the amount of cross-linkage in polymer structure, which is the most important parameter of both pattern generation and remaining stress. Heat treatment is dealed with soft bake and post-exposure-bake. Temperature and time duration of each step are varied with heat treatment condition. Some test patterns are fabricated to evaluate the proposed process. Nickel electroplating is performed with the mold fabricated through the proposed process to confirm the SU-8 as a good electroplating mold.

• 열처리공학회지
• /
• 제7권1호
• /
• pp.61-71
• /
• 1994

This study is to investigate the stress distributions, crystal orientations and magnetic properties during die-upsetting according to working temperature of Nd-Fe-B-Cu alloys. The stress distributions in the specimens during compressing process were calculated by a finite element method program(SPID). The calculated stresses were effective stress (${\sigma}_{eff}$), compression stress(${\sigma}_z$), radial direction stress(${\sigma}_r$) rotational direction stress(${\sigma}_e$) and shear stress(${\tau}_{rz}$). The stress distributions of ${\sigma}_z$, obtained by a computer simulation showed that the stress components causing the magnetic alignment during die-upsetting of the cast magnets were very high at the center-part of a specimen, and decreased toward the periphery-part of a specimen. In view of the above results the magnetic properties should be better at the center-part of a specimen than any other parts. But the measured magnetic properties were better at the mid-part. These results should be due to the fact that the specimens were casted. Normally the magnetic properties are affected by the casting process as well as by the stress levels. ${\sigma}_r$, ${\sigma}_e$ are thought to affect the liquid phase flowing and domain patterns, respectively. The influence of ${\tau}_{rz}$ was trivial, ${\sigma}_{eff}$ distributed similar throughout the specimen. The Nd-rich phase appeared at the peripheral of the specimen where the stress level of ${\sigma}_r$, ${\sigma}_z$, was low or the stress level of ${\sigma}_e$ was high. The Nd-rich phase was squeezed out during die-upsetting. This phase had an effect on the crystal orientation and grain growth. The stress distributions of alloy were irregular at the parts of the specimen where the die contacted with specimen.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권8호
• /
• pp.1013-1019
• /
• 2007

This paper is about structural analysis of globe valve for controlling cryogenic LNG's flow or stop in normal temperature. The used valve is demanded safety resistance for inner pressure and temperature variation caused by using it in cryogenic, high pressure surrounding. This study evaluates for safety resistance for inner pressure and temperature variation by heat transfer analysis in cryogenic surrounding, heat stress analysis in temperature variation and deformation analysis in high pressure.