• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.138-139
• /
• 2017

This paper describes the design and implementation of a trigger circuit which can be series connected with main pulse circuit for a xenon flash lamp driver. For generating high voltage, the trigger circuit is designed as an inductive energy storage pulsed power modulator with 2 state step-up circuit consisting of a boost converter and a flyback circuit. In order to guarantee pulse width, a resonant capacitor on the output side of the flyback circuit is designed. This capacitor limits the output voltage to protect the flyback switch. In addition, to protect another power supply of xenon flash lamp driver from trigger pulse, the high voltage transformer which can carry the full current of main pulse is designed. To verify the proposed design, the trigger circuit is developed with the specification of maximum 23 kV, 0.6 J/pulse output and tested with a xenon flash lamp driver consisting of a main pulse circuit and a simmer circuit.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.2
• /
• pp.360-369
• /
• 2008

The solar cells should be operated at the maximum power point because its output characteristics were greatly fluctuated on the variation of insolation, temperature and load. It is necessary to install an inverter among electric power converts by means of the output power of solar cell is DC. The inverter is operated supply a sinusoidal current and voltage to the load and the interactive utility line. In this paper, the proposes a photovoltaic system is designed with a step up chopper and single phase PWM voltage source inverter. Synchronous signal and control signal was processed by one-chip microprocessor for stable modulation. The step up chopper is operated in continuous mode by adjusting the duty ratio so that the photovoltaic system tracks the maximum power point of solar cell without any influence on the variation of insolation and temperature for solar cell has typical dropping character. The single phase PWM voltage source inverter is consists of complex type of electric power converter to compensate for the defect, that is, solar cell cannot be develop continuously by connecting with the source of electric power for ordinary using. It can be cause the efect of saving electric power, from 10 to 20%. The single phase PWM voltage source inverter operates in situation, that its output voltage is in same phase with the utility voltage. The inverter are supplies an ac power with high factor and low level of harmonics to the load and the utility power system.

• Journal of the Korea Society of Computer and Information
• /
• v.14 no.2
• /
• pp.157-168
• /
• 2009

In this paper, a photovoltaic system is designed with a step up chopper and single phase PWM(Pulse Width Modulation) voltage source inverter. Where proposed Synchronous signal and control signal was processed by one-chip microprocessor for stable modulation. The step up chopper operates in continuous mode by adjusting the duty ratio so that the photovoltaic system tracks the maximum power point of solar cell without any influence on the variation of insolation and temperature because solar cell has typical voltage and current dropping character. The single phase PWM voltage source the inverter using inverter consists of complex type of electric power converter to compensate for the defect, that is, solar cell cannot be developed continuously by connecting with the source of electric power for ordinary use. It can cause the effect of saving electric power. from 10 to 20[%]. The single phase PWM voltage source inverter operates in situation that its output voltage is in same phase with the utility voltage. In order to enhance the efficiency of photovoltaic cells, photovoltaic positioning system using sensor and microprocessor was design so that the fixed type of photovoltaic cells and photovoltaic positioning system were compared. In result, photovoltaic positioning system can improved 5% than fixed type of photovoltaic cells. In addition, I connected extra power to the system through operating the system voltage and inverter power in a synchronized way by extracting the system voltage so that the phase of the system and the phase of single-phase inverter of PWM voltage type can be synchronized. And, It controlled in order to provide stable pier to the load and the system through maintaining high lurer factor and low output power of harmonics.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1066-1070
• /
• 2003

Recently technologies have created new principle and theory but the PID control system remains its popularity as the PID controller contains simple structure, including maintenance and parameter adjustment being so simple. Thus, this paper proposes auto tune PID by fuzzy logic controller based on FPGA which to achieve real time and small size circuit board. The digital PID controller design to consist of analog to digital converter which use chip TDA8763AM/3 (10 bit high-speed low power ADC), digital to analog converter which use two chip DAC08 (8 bit digital to analog converters) and fuzzy logic tune digital PID processor embedded on chip FPGA XC2S50-5tq-144. The digital PID processor was designed by fundamental PID equation which architectures including multiplier, adder, subtracter and some other logic gate. The fuzzy logic tune digital PID was designed by look up table (LUT) method which data storage into ROM refer from trial and error process. The digital PID processor verified behavior by the application program ModelSimXE. The result of simulation when input is units step and vary controller gain ($K_p$, $K_i$ and $K_d$) are similarity with theory of PID and maximum execution time is 150 ns/action at frequency are 30 MHz. The fuzzy logic tune digital PID controller based on FPGA was verified by control model of level control system which can control level into model are correctly and rapidly. Finally, this design use small size circuit board and very faster than computer and microcontroller.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.286-288
• /
• 2008

본 논문은 낮은 입력 DC전압에서 높은 음의 DC전압을 출력하는 높은 전환 비의 극성 반전 형 DC/DC 전력 변환 회로에 관한 것으로써, 하나의 스위치, 하나의 인덕터, 그리고 다수개의 캐패시터와 다이오드로 구성된다. 기존의 극성 반전 형 DC/DC 컨버터 회로와 비교하여, 고압 변환 트랜스포머 대신에 인덕터를 사용할 수 있어, 자기 소자의 부피 및 크기는 물론 원가저감이 가능하다. 또한 자려 발진(Self Oscillation) 방식을 사용하여 별도의 제어 IC가 필요 없으므로, 회로구성이 대단히 간단하고, 저가격의 전원 회로를 만들 수 있다. 또한 다이오드들의 전압 스트레스가 감소하여 저가격 고성능의 고압 변환장치 구현이 가능하다. 제안된 회로의 동작원리를 설명하고, 타당성을 Simulation 및 실험을 통하여 검증한다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.6
• /
• pp.1175-1186
• /
• 2020

In this study, the problem is analyzed, and methods of improvement are presented. For evaluating the performance of the proposed EGT sensor, a complex environment test equipment has been developed to test both high temperature and vibration conditions at the same time. This equipment evaluates the accuracy and response time of the EGT sensor. In the results of the comparison test of the complex environment test equipment of heat and vibration, the existing sensor showed a carbonization problem, and the proposed sensor showed no problem. Therefore, it is expected that the improved EGT sensor will be able to be applied to various industrial fields, including gas turbines for power generation.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.6
• /
• pp.117-125
• /
• 2007

Recently, a fuel cell with low voltage and high current output characteristics is remarkable for new generation system. It needs both a DC-DC step-up converter and DC-AC inverter to be used in fuel cell generation system. Therefor, this paper, consists of an isolated DC-DC converter to boost the fuel cell voltage 380[VDC] and a PWM inverter with LC filter to convent the DC voltage to single-phase 220[VAC]. Expressly, The fuel cell system which it proposes DC-DC the efficient converter used PWM the phase transient control law and it depended to portion resonance ZVS switching, loss peek voltage and electric current of realization under make schedule, switching frequency anger and the switch reduction. And mind benevolence it sprouted 2 in stop circuit and it added and a direct current voltage and the electric current where the ingredient is reduced in load side ripple stable under make whom it will be able to supply. Besides the efficiency of 92[%]is obtained over the wide output voltage regulation ranges and load variations. Also, under make over together the result leads simulation and test, the propriety confirmation.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.490-492
• /
• 2008

고압 전원 장치(High Voltage Power Supply)는 근래에 와서 산업전반에 응용이 매우 광범위하게 확산되고 있고 고전압 장치가 필수적으로 이용 되어야 하는 분야가 점차 확산되고 있다. 응용분야로는 신소재 개발과 플라즈마 응용을 위한 공업용과 민생용, 의료기기용, 군사용, 또한 프린터에 이르기까지 다양하게 있다. 가정이나 사무실에서 쉽게 접할 수 있는 IT장비인 프린터인 경우에도 전원 공급 장치의 측면에서는 화상형성에 있어 가장 필수적인 안정적이고 다기능을 가지는 고압 전원장치를 적용하고 있고, 수요 또한 증가하고 있다. 본 논문은 낮은 입력 DC전압에서 높은 음의 DC전압을 출력하는 높은 전환 비의 극성 반전 형 DC/DC 전력 변환 회로에 관한 것으로써, 하나의 스위치, 하나의 인덕터, 그리고 다수개의 캐패시터와 다이오드로 구성된다. 기존의 극성 반전 형 DC/DC 컨버터 회로와 비교하여, 고압 변환 트랜스포머 대신에 인덕터를 사용할 수 있어, 자기 소자의 부피 및 크기는 물론 원가저감이 가능하다. 또한 반도체 소자의 Voltage Stress가 감소된다. 제안된 회로의 원리를 분석하고, 종래의 고압 전원장치와 비교함으로써 장점을 알아본 후, 동작원리에 대한 타당성을 Simulation 및 실험을 통하여 검증한다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.4
• /
• pp.405-414
• /
• 2011

Recently, the development of several hundreds of kW scale PCS for fuel cell generation is required as commercialization process of distributed generation systems using high temperature fuel cells such as MCFC begins. This paper proposes and optimized topology suitable for MCFC fuel cell generation system and LCL filter design method considering voltage quality of local loads such as MBOP. An interleaving technique is applied to step-up DC-DC converter, optimized number of phases is determined considering efficiency and volume. Also, a LCL filter design method is proposed considering quality of current injected to the grid as well as that of voltage across the local load. The proposed PCS system is validated through reduced 1kW prototype.