• Nuclear Engineering and Technology
• /
• 제43권6호
• /
• pp.557-566
• /
• 2011

A cold spray coating (CSC) of copper was studied for its application to a high-level radioactive waste (HLW) disposal canister. Several copper coatings of 10 mm thick were fabricated using two kinds of copper powders with different oxygen contents, and SS 304 and nodular cast iron were used as their base metal substrates. The fabricated CSC coppers showed a high tensile strength but were brittle in comparison with conventional non-coating copper, hereinafter defined to as "commercial copper". The corrosion behavior of CSC coppers was evaluated by comparison with commercial coppers, such as extruded and forged coppers. The polarization test results showed that the corrosion potential of the CSC coppers was closely related to its purity; low-purity (i.e., high oxygen content) copper exhibited a lower corrosion potential, and high-purity copper exhibited a relatively high corrosion potential. The corrosion rate converted from the measured corrosion current was not, however, dependent on its purity: CSC copper showed a little higher rate than that of commercial copper. Immersion tests in aqueous HCl solution showed that CSC coppers were more susceptible to corrosion, i.e., they had a higher corrosion rate. However, the difference was not significant between commercial copper and high-purity CSC copper. The decrease of corrosion was observed in a humid air test presumably due to the formation of a protective passive film. In conclusion, the results of this study indicate that CSC application of copper could be a useful option for fabricating a copper HLW disposal canister.

• 열처리공학회지
• /
• 제25권1호
• /
• pp.22-26
• /
• 2012

An influence of the addition of copper (0.5, 1.0 and 1.5 mass% Cu) on the microstructure and mechanical properties of high purity iron (99.998 mass%) was characterized. The microstructure and microhardness of high-purity iron based samples, which were rolled at room temperature and subsequently annealed, were investigated in this work. The microstructure of the samples has been observed by electron back scattering diffraction (EBSD) and the mechanical properties have been studied by using micro-Vickers hardness test. The results of microstructural observation showed that deformation band was formed in high purity iron by rolling at room temperature, and it was recovered by annealing up to about 900 K. The microhardness results showed that the softening of high-purity iron occurred by annealing up to about 900 K, while the hardness of iron added with about 0.5-1.5 mass% copper was kept over 100 Hv and at the early time of annealing reached a maximum. The hardness of iron added with a small amount of copper may be attributed to precipitation hardening as well as solution hardening. The orientation of crystal in recrystallized grain was almost same as that of deformed grain.

• 자원리싸이클링
• /
• 제26권6호
• /
• pp.84-90
• /
• 2017

저품위 동 함유 슬러지로부터 회수된 동 조금속을 황산구리 전해액에서 전해정련을 수행하여 고순도 동을 회수하고자 하였다. 유기첨가제 종류 및 농도에 따른 전해정련동 표면 형상 및 조도를 분석하였을 때, gelatin계 유기첨가제 5 ppm 및 thiol계 유기첨가제 5~10 ppm 혼합 조건에서 가장 우수한 표면 형상을 얻을 수 있었다. 건식환원공정을 통해 회수한 철(Fe), 니켈(Ni), 코발트(Co) 및 주석(Sn) 등의 불순물이 함유된 각 86.635, 94.969 및 99.917 wt.% 순도의 동 조금속을 사용하여 전해정련하였고, 순도 3N~4N급 전해정련동을 얻을 수 있었다. 동 조금속, 전해액, 전해정련동의 불순 원소 농도 및 동 순도 등의 분석을 통해, 순도 99.99 wt.% 이상 전해정련동을 회수할 수 있는 전해정련 공정시간 및 동 조금속 순도를 도출하였다.

• 자원리싸이클링
• /
• 제28권1호
• /
• pp.62-72
• /
• 2019

일반적으로, 황산동을 제조하기 위한 원료는 $H_2SO_4$ 및 Cu 금속이 사용된다. 본 연구는 폐산, 폐염화동 폐기물부터 전해 채취법을 이용하여 황산동을 제조하는 방법에 관한 것이다. 황산구리의 용도는 공업용, 도금용, 사료용, 농업용, 전자급 PCB 동도금에 사용된다. 종래의 황산동 제조법은 다량의 폐수 및 에너지 비용이 높은 문제점이 있다. 구리(Cu) 화합물 중에서 가장 사용이 많이 되는 황산동($CuSO_4$)의 제조 방법에 관한 연구로서, 공정 운전비가 적고, 폐수 발생이 적으며, 제조 공정이 간단하다. 양이온 맴브레인을 이용하여 Na, Ca, Mg, Al을 불순물로서 제거하기 쉽다. 또한 동시에 전해 채취 방법으로 고 순도 구리 분말을 회수 할 수 있었다. 회수 된 구리 분말을 사용하여 고 순도 황산동을 제조 할 수 있었다.

• 대한화학회지
• /
• 제11권4호
• /
• pp.132-137
• /
• 1967

8-Hydroxy-Quinoline(Qxine)에 依한 高純度 Antimony中 不純物(鐵 및 銅)의 吸光光度 定量法을 檢討하였다. 試料의 黃酸溶液에 안티몬을 Masking하기 위하여 必要한 酒石酸의 影響을 調査한 結果, 0.5M-酒石酸溶液 10ml로서 600mg 까지의 안티몬을 Masking할 수 있었다. pH 範圍는 鐵은 5.0-5.7, 銅은 3.5-4.0이었다. 鐵은 580$m{\mu}$ 에서 吸光度를 測定하면 되나, 銅은 15%苛性소오다溶液으로 逆抽出하고, 남은 鐵을 580$m{\mu}$, 410$m{\mu}$ 에서 測定하여 補正할 必要가 있다. 500mg 안티몬에 對하여 鐵은 150${\mu}g$(0.005~0.03%)까지, 銅은 100${\mu}g$(0.005~0.016%)까지 定量이 可能했다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.413-416
• /
• 2007

In general, by means of the electrodepositing technique, a copper foil sample was prepared with a high purity and a high density. But the mechanical properties of the electrodepositing copper foil was lower than it's the rolling copper foil. However, the production of copper foil with approximately 36 microns thick in rolling process was very difficult. This paper describes the outline of the high accuracy cold rolling in 6 high mill which was developed for the purpose of rolling very thin accurate gauge copper foil(36 micron thick), and give several rolling characteristic of 600 mm wide copper foil. a) Large strain can be accumulated pass by pass in industrial multi-pass rolling processing to overcome large critical strain for thickness accuracy through optimization of rolling schedule. b) Also, permissible tension for rolling 0.45 $\sim$ 0.036 mm thick copper strip stably in accordance with the each pass work had been established by FEM simulation results. c) During the plate rolling process, considerable values of the forces of material pressure on the tool occur. These pressures cause the elastic deformation of the roll, thus changing the shape of the deformation region. A numerical simulation of roll deflection during cold rolling is presented in the paper. d) The proposed pass schedule can roll very thin copper foil of 36 micron thickness to a tolerance of ${\pm}1$ microns. The validity of simulated results was verified into rolling experiments on the copper foil.

• 대한화학회지
• /
• 제39권4호
• /
• pp.252-256
• /
• 1995

고순도 구리 금속중에 존재하는 미량의 안티몬을 사전 분리시키지 않고 직접 분석할 수 있는 GFAAS 조건을 조사하였다. 과량 존재하는 구리가 안티몬의 감도를 향상시키는 matrix modifier의 역할을 하고 있음을 알았다. 희화 온도는 $600^{\circ}C(20s){\sim}700^{\circ}C(10s)$를 이용할 때에 $1000^{\circ}C(20s){\sim}1100^{\circ}C(10s)$보다 감도가 향상되며, 원자화 온도는 $2200^{\circ}C$에서 가장 좋은 Sb의 흡광도를 보였다. Ar 기체의 압력은 $2.0\; kg/cm^2$일때에 최적임을 확인하였으며, 20 ppb에서 200 ppb Sb 범위에서 변화율(coefficient of variation)이 5% 미만이며 직선 관계를 보였다.

• 자원리싸이클링
• /
• 제30권6호
• /
• pp.76-82
• /
• 2021

폐 전자폐기물에서 건식정련 및 팔라듐 농축공정으로 제조된 조금속으로부터 팔라듐 분리 및 고순도 동 회수가 가능한 전해공정 연구를 수행하였다. 조금속 내 팔라듐 및 불순금속을 전해분리 시키기 위한 기초 연구로서 각 금속별 산화전위를 평가한 결과 구리, 철 및 니켈은 전해액에 용해되고, 팔라듐 및 알루미늄은 산화물 형태 슬라임 회수가 가능한 것으로 나타났다. 조금속 사용 팔라듐 분리 전해공정 시 팔라듐은 산화물 형태의 슬라임으로 분리되어 97.46 %의 손실이 거의 없는 팔라듐 회수가 가능하였고, 음극에서의 전착층에서는 4N급 구리를 회수하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.260-260
• /
• 2009

In high-efficiency crystalline silicon solar cell, If high-efficiency solar cells are to be commercialized, It is need to develop superior contact formation method and material that can be inexpensive and simple without degradation of the solar cells ability. For reason of plated metallic contact is not only high metallic purity but also inexpensive manufacture. It is available to apply mass production. Especially, Nickel, Copper are applied widely in various electronic manufactures as easily formation is available by plating. Ni is shown to be a suitable barrier to Cu diffusin as well as desirable contact metal to silicon. Nickel monosilicide has been suggested as a suitable silicide due to its lower resistivitym lower sintering temperature and lower layer stress than $TiSi_2$. In this paper, Nickel as a seed layer and diffusion barrier is plated by electroless plating to make nickel monosilicide.

• Tribology and Lubricants
• /
• 제26권2호
• /
• pp.122-128
• /
• 2010

Focused Ion Beam (FIB) has been used for site-specific TEM sample preparation and small scale fabrication. Moreover, analysis on the surface microstructure and phase distribution is possible by ion channeling contrast of FIB with high resolution. This paper describes FIB applications and deformed surface structure induced by sliding. The effect of FIB process on the surface damage was explored as well. The sliding experiments were conducted using high purity aluminum and OFHC(Oxygen-Free High Conductivity) copper. The counterpart material was steel. Pin-on-disk, Rotational Barrel Gas Gun and Explosively Driven Friction Tester were used for the sliding experiments in order to investigate the velocity effect on the microstructural change. From the FIB analysis, it is revealed that ion channeling contrast of FIB has better resolution than SEM and the tribolayer is composed of nanocrystalline structures. And the thickness of tribolayer was constant regardless of sliding velocities.