• Journal of Korea Water Resources Association
• /
• v.55 no.8
• /
• pp.623-634
• /
• 2022

Due to river maintenance projects such as the creation of hydrophilic areas around rivers and the Four Rivers Project, the flow characteristics of rivers are continuously changing, and the risk of water quality accidents due to the inflow of various pollutants is increasing. In the event of a water quality accident, it is necessary to minimize the effect on the downstream side by predicting the concentration and arrival time of pollutants in consideration of the flow characteristics of the river. In order to track the behavior of these pollutants, it is necessary to calculate the diffusion coefficient and dispersion coefficient for each section of the river. Among them, the dispersion coefficient is used to analyze the diffusion range of soluble pollutants. Existing experimental research cases for tracking the behavior of pollutants require a lot of manpower and cost, and it is difficult to obtain spatially high-resolution data due to limited equipment operation. Recently, research on tracking contaminants using RGB drones has been conducted, but RGB images also have a limitation in that spectral information is limitedly collected. In this study, to supplement the limitations of existing studies, a hyperspectral sensor was mounted on a remote sensing platform using a drone to collect temporally and spatially higher-resolution data than conventional contact measurement. Using the collected spatio-temporal hyperspectral images, the tracer concentration was calculated and the transverse dispersion coefficient was derived. It is expected that by overcoming the limitations of the drone platform through future research and upgrading the dispersion coefficient calculation technology, it will be possible to detect various pollutants leaking into the water system, and to detect changes in various water quality items and river factors.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.50 no.5
• /
• pp.80-89
• /
• 2022

In order to solve the limitations of horizontal thermal environment improvement, this study compared the thermal environment of the indoor and outdoor of a building in summer according to the presence or absence of a green curtain, a vertical greening method. In the summer of 2021, the air temperature, relative humidity, wind speed, and shortwave and longwave radiation were measured at a central point inside a building and the grass field outside of the building to determine the human thermal sensation index, PET and UTCI. As a result, the green curtain showed an average 1.6℃ cooler air temperature during the daytime, but it did not have an effect at night. For relative humidity, it showed higher humidity indoors by an average of 5.6% and 1.0% during the daytime and at night, respectively. Wind speed was 1.4-1.8 ms^-1 and 1.4-1.5 ms^-1 higher outdoors on average during the daytime and at night, respectively, showing a high value outdoors regardless of whether a green curtain was installed. The green curtain showed an average indoor mean radiant temperature reduction effect of 4.7℃ during the daytime, but it did not have an effect at night. In PET and UTCI, the green curtain reduced the indoor PET by about a 1/3 level, an average of 2.1℃, and the indoor UTCI by about a 1/6 level, an average of 1.1℃, during the daytime. However, no effects appeared in PET and UTCI at night. For landscape planning, a green curtain can effectively modify the thermal environment during the daytime in summer.

• Korean Journal of Environment and Ecology
• /
• v.36 no.6
• /
• pp.651-661
• /
• 2022

Plants social network analysis, which combines plants society and social network analyses, is a new research method for understanding plants society. This study was conducted to investigate the relationship between species, using plant social network analysis targeting Taejongdae in Busan, and build basic data for management. Taejongdae, located in the warm temperate forest in Korea, is a representative coastal forest of Busan Metropolitan City, and the Pinus thunbergii-Eurya japonicacommunity is widely distributed. This study set up 100 quadrats (size of 100m²each) in Taejongdae to investigate the species that emerged and analyzed the interspecies association focusing on major species. Based on the results, a sociogram was created using the Gephi 0.9.2, and the network centrality and structure were analyzed. The results showed that the frequency of appearance was high in the order of P. thunbergii, E. japonica, Quercus serrata, Sorbus alnifolia, Ligustrum japonicum, and Styrax japonicusand that many evergreen broad-leaved trees appeared due to the environmental characteristics of the site. The plants social network of Taejongdae was composed of a small-scale network with 50 nodes and 172 links and was divided into 4 groups through modularization. The succession sere identified through a sociogram confirmed that the group that include P. thunbergiiand E. japonicawould progress to a deciduous broadleaf community dominated by Q. serrataand Carpinus tschonoskii, using hub nodes such as Prunus serrulataf. spontaneaand Toxicodendron trichocarpum. Another succession sere was highly likely to progress to an evergreen broad-leaved community dominated by Machilus thunbergiiand Neolitsea sericea, using M. thunbergiias a medium. In some areas, a transition to a deciduous broad-leaved community dominated by Celtis sinensis, Q. variabilisand Zelkova serratausing Lindera obtusilobaand C. sinensisas hub nodes was expected.

• Journal of Service Research and Studies
• /
• v.13 no.2
• /
• pp.114-129
• /
• 2023

In the era of the 4th industrial revolution, the importance of the 4th industrial revolution technology is increasing in the service industry. The purpose of this study is to identify the development and utilization status of the 4th industrial revolution technology in the service industry and to derive the characteristics and implications of the 4th industrial revolution technology innovation in the service industry. In this study, research and analysis were conducted based on the business activity survey data in order to identify the technological innovation characteristics of the 4th industrial revolution in the service industry. The 4th industrial revolution technology in the service industry was analyzed in terms of company ratio, technology development and utilization rate, development/utilization technology, technology application field, and technology development method. In addition, the trend of the 4th industrial revolution technology change in the service industry was also analyzed. The 4th industrial revolution technology utilization and development status of other industries was compared and analyzed. In particular, the service industry 4th industrial revolution technology innovation type was divided into 4 types from the perspective of the 4th industrial revolution company ratio and the 4th industrial revolution company ratio growth rate, and types for each service industry were derived. The characteristics and implications of the 4th industrial revolution technology innovation in the service industry were presented from nine perspectives. As a result of the study, it was found that companies in the service industry were developing or using 4th industrial revolution technologies more actively than companies in other industries, and it was analyzed that the gap was further widening. By service industry, information and communication, finance and insurance, and educational service showed relatively high rates of developing or utilizing 4th industrial revolution technologies. The service industries in which the share of 4th industrial revolution companies increased the most were real estate, education service, health and social welfare service. In particular, cloud, big data, and artificial intelligence were analyzed as the three core technologies of the fourth industrial revolution. The service industry can be classified into 4 types in terms of the 4th industrial revolution company ratio and growth rate, and service industry innovation measures that reflect the differentiated innovation characteristics of each type are needed.

• Korea Trade Review
• /
• v.42 no.5
• /
• pp.137-159
• /
• 2017

This study divides manufacturing in 18 countries including Korea, China, Japan and OECD countries into 11 areas and estimates and compares the technological efficiency of each industry. The traditional view of productivity is to increase production capacity through technological innovation or process innovation, but it is also influenced by the technological efficiency of production process. A Stochastic Frontier Production Model (SFM) is a representative method for estimating the technical efficiency of such production. First, as a result of estimating the production function by setting the output variable as total output or value-added, in both cases, the output increased significantly in all manufacturing sectors as inputs of labor, capital, and intermediate increased. On the other hand, R&D investment has a large impact on output in chemical, electronics, and machinery industries. Next, as a result of estimating the technological efficiency through the production function, when the total output is set as the output variable, the overall average of each sector is 0.8 or more, showing mostly high efficiency. However, when value-added was set, Japan had the highest level in most manufacturing sectors, while other countries were lower than the efficiency of the total output. Comparing the three countries of Korea, China and Japan, Japan showed the highest efficiency in most manufacturing sectors, and Korea was about half or one third of Japan and China was lower than Korea. However, in the food and electronics sectors, China is higher than Korea, indicating that China's production efficiency has greatly improved. As such, Korea is not able to narrow its gap with Japan relatively faster than China's rapid growth. Therefore, various policy supports are needed to promote technology development. In addition, in order to improve manufacturing productivity, it is necessary to shift to an economic structure that can raise technological efficiency as well as technology development.

• Economic and Environmental Geology
• /
• v.56 no.3
• /
• pp.311-330
• /
• 2023

Development of Carbon Capture and Storage (CCS) technique is becoming increasingly important as a method to mitigate the strengthening effects of global warming, generated from the unprecedented increase in released anthropogenic CO₂. In the recent years, the characteristics of basaltic rocks (i.e., large volume, high reactivity and surplus of cation components) have been recognized to be potentially favorable in facilitation of CCS; based on this, research on utilization of basaltic formations for underground CO₂ storage is currently ongoing in various fields. This study investigated the feasibility of underground storage of CO₂ in basalt, based on the examination of the CO₂ storage mechanisms in subsurface, assessment of basalt characteristics, and review of the global research on basaltic CO₂ storage. The global research examined were classified into experimental/modeling/field demonstration, based on the methods utilized. Experimental conditions used in research demonstrated temperatures ranging from 20 to 250 ℃, pressure ranging from 0.1 to 30 MPa, and the rock-fluid reaction time ranging from several hours to four years. Modeling research on basalt involved construction of models similar to the potential storage sites, with examination of changes in fluid dynamics and geochemical factors before and after CO₂-fluid injection. The investigation demonstrated that basalt has large potential for CO₂ storage, along with capacity for rapid mineralization reactions; these factors lessens the environmental constraints (i.e., temperature, pressure, and geological structures) generally required for CO₂ storage. The success of major field demonstration projects, the CarbFix project and the Wallula project, indicate that basalt is promising geological formation to facilitate CCS. However, usage of basalt as storage formation requires additional conditions which must be carefully considered - mineralization mechanism can vary significantly depending on factors such as the basalt composition and injection zone properties: for instance, precipitation of carbonate and silicate minerals can reduce the injectivity into the formation. In addition, there is a risk of polluting the subsurface environment due to the combination of pressure increase and induced rock-CO₂-fluid reactions upon injection. As dissolution of CO₂ into fluids is required prior to injection, monitoring techniques different from conventional methods are needed. Hence, in order to facilitate efficient and stable underground storage of CO₂ in basalt, it is necessary to select a suitable storage formation, accumulate various database of the field, and conduct systematic research utilizing experiments/modeling/field studies to develop comprehensive understanding of the potential storage site.

• Journal of the Korean Society for information Management
• /
• v.39 no.4
• /
• pp.191-213
• /
• 2022

With a view to providing a high-quality policy information service beyond the existing national task service of the national policy information portal (POINT) of the National Library of Korea Sejong, it would be necessary to effectively provide the policy data needed for the implementation of the new national tasks. Accordingly, in this study, an attempt has been made to find a way to connect and develop the BRM-based national tasks and the policy information contents. Towards this end, first, the types of national tasks and the contents of each field and area of the government function's classification system were analyzed, with a focus placed on the 120 national tasks of the new administration. Furthermore, by comparing and analyzing the national tasks of the previous administration and the current information, the contents ought to be reflected for the development of contents related to the national tasks identified. Second, the method for linking and collecting the policy information was sought based on the analysis of the current status of policy information and the national information portal. As a result of the study, first, examining the 1st stage BRM of the national tasks, it turned out that there were 21 tasks for social welfare, 14 for unification and diplomacy, 17 for small and medium-sized businesses in industry and trade, 12 for general public administration, 8 for the economy, taxation and finance, 6 for culture, sports and tourism, science and technology, and education each, 5 for communication, public order and safety each, 4 for health, transportation and logistics, and environment each, 3 for agriculture and forestry, 2 for national defense and regional development each, and 1 for maritime and fisheries each, among others. As for the new administration, it is apparent that science technology and IT are important, and hence, it is necessary to consider such when developing the information services for the core national tasks. Second, to link the database with external organizations, it would be necessary to form a linked operation council, link and collect the information on the national tasks, and link and provide the national task-related information for the POINTs.

• Journal of Korea Entertainment Industry Association
• /
• v.13 no.2
• /
• pp.145-154
• /
• 2019

The purpose of this study is to investigate the performance, learning motivation and satisfaction of the students who take the university 's Lifelong Education Program. The research method was interviewed. The results are as follows. In terms of operations; First, the awareness of the kindness of employees of the college lifelong education institute needs to be strengthened at the beginning of the school year. Second, in the operation of the College Lifelong Education Center, the support such as the parking fee should be extended to the students. Third, lifelong education facilities should be supplemented. In terms of participation motivation; First, it can be seen that there are the most learners who want to do complementary learning. Most of them are people who look back on their lives and prepare for their future directions. Second, as the life span of human beings became longer, the economic preparation for life became necessary. Thus, all learning tends to be perceived as a preparation for economic income. Third, most people who participate in lifelong education are very interested in health. Therefore, it is necessary to increase the motivation for participation by expanding health related programs. In terms of satisfaction; First, it depends on the purpose of the individual. Satisfaction was high for those who aimed at hobbies and relationships, and satisfaction for those who aimed for economic activities was low. Second, it is also necessary to consider the instructor 's instructional process. In other words, lifelong learners tend to be adults, so little complaints are not revealed. Therefore, I would like to ask the lecturers to advance the education for the class. The implications for the improvement direction of the lifelong education center are as follows; First, we need to drastically reduce the number of programs overlapping with other universities and conduct research to develop new programs. In order to do this, it is necessary to continuously carry out a survey of demanders' needs. Second, it is necessary to find the appropriate place for program operation considering the movement distance of learners. It should be avoided that the program should be operated with the existing university facilities. Third, universities' lifelong education should go to education that includes college students.

• Korean Journal of Remote Sensing
• /
• v.39 no.5_3
• /
• pp.1009-1029
• /
• 2023

Urban trees play a vital role in urban ecosystems,significantly reducing impervious surfaces and impacting carbon cycling within the city. Although previous research has demonstrated the efficacy of employing artificial intelligence in conjunction with airborne light detection and ranging (LiDAR) data to generate urban tree information, the availability and cost constraints associated with LiDAR data pose limitations. Consequently, this study employed freely accessible, high-resolution multispectral satellite imagery (i.e., Sentinel-2 data) to estimate fractional tree canopy cover (FTC) within the urban confines of Suwon, South Korea, employing machine learning techniques. This study leveraged a median composite image derived from a time series of Sentinel-2 images. In order to account for the diverse land cover found in urban areas, the model incorporated three types of input variables: average (mean) and standard deviation (std) values within a 30-meter grid from 10 m resolution of optical indices from Sentinel-2, and fractional coverage for distinct land cover classes within 30 m grids from the existing level 3 land cover map. Four schemes with different combinations of input variables were compared. Notably, when all three factors (i.e., mean, std, and fractional cover) were used to consider the variation of landcover in urban areas(Scheme 4, S4), the machine learning model exhibited improved performance compared to using only the mean of optical indices (Scheme 1). Of the various models proposed, the random forest (RF) model with S4 demonstrated the most remarkable performance, achieving R² of 0.8196, and mean absolute error (MAE) of 0.0749, and a root mean squared error (RMSE) of 0.1022. The std variable exhibited the highest impact on model outputs within the heterogeneous land covers based on the variable importance analysis. This trained RF model with S4 was then applied to the entire Suwon region, consistently delivering robust results with an R² of 0.8702, MAE of 0.0873, and RMSE of 0.1335. The FTC estimation method developed in this study is expected to offer advantages for application in various regions, providing fundamental data for a better understanding of carbon dynamics in urban ecosystems in the future.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.12
• /
• pp.61-67
• /
• 2023

Heat pipes located underground in urban areas and operated under high temperature and pressure conditions can cause large-scale human and economic damage if damaged. In order to predict damage in advance, damage and construction information of heat pipe are analyzed to derive independent variables that have a correlation with frequency of damage, and a simple regression analysis modified model using each variable is applied to the field. However, as the correlation between independent variables applied to the model increases, the independence between variables is harmed and the reliability of the model decreases. In this study, the independence of the pipe diameter, burial depth, insulation level of monitoring system, and disconnection or short circuit of the detection line, which are judged to be interrelated, was tested to derive a method for combining variables and setting categories necessary to apply to the frequency of damage estimation model. For the test of independence, the continuous variables pipe diameter and burial depth were each converted into three categories, insulation level of monitoring system was converted into two categories, and the categorical variable disconnection or short circuit of the detection line status was kept as two categories. As a result of the test of independence, p-value between pipe diameter and burial depth, level of monitoring system and disconnection or short circuit of the detection line was lower than the significance level (α = 0.05), indicating a large correlation between them. Therefore, the pipe diameter and burial depth were combined into one variable, and the categories of the combined variable were set to 9 considering the previously set categories. The insulation level of monitoring system and the disconnection or short circuit of the detection line were also combined into one variable. Since the insulation level is unreliable when the detection line status is disconnection or short circuit, the categories of the combined variable were set to 3.