• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.721-722
• /
• 2006

Industrialization and technique consequently in quick development the motor field small size and light weight, high efficiency and highly energy density in necessity. The permanent magnet motor small size and the research regarding the research of the torque and efficiency is coming to be active. From this paper the research regarding the quality permanent magnet motor and analysis and it was developed recently the NdFeB anisotropic bond magnet which is a high magnetic force material use, from the hazard which accomplishes power density it is high permanent magnet motor of small size and light weight it researched. The Finite Element Method it led and motor optimization. Also the experiment and analysis permanent magnet motor it is improved the motor and result it led and different it compared.

• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.184-185
• /
• 2013

In this paper, design of a variable inductor using MR Fluid Gap is proposed for wide load range efficiency improvement of a bidirectional DC-DC converter. As compared to conventional constant value inductor designed to have negative current for ZVS at heavy load but suffers high losses at light load due to its small inductance, the proposed variable inductor not only have small inductance at high current for ZVS but also it has large inductance at low current to decrease light load losses.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.2
• /
• pp.131-137
• /
• 2003

We have performed computer simulation to obtain electro-optic chracteristics of reflective liquid crystal display (LCD) using wide viewing angle LC mode, fringe field switching(FFS). Unlike other reflective LCD modes, in the FFS mode, the LC director in plance so an application to reflective display consisted of polarizer, LC layer and reflector is possible. when an incident light is 550mm, the optimal cell retardation value is 0.1365${\mu}$m and the efficiency of reflectivity is high over 90% with very little wavelength dispersion. Further, we have studied a new reflective display with polarizer, optical compensation film with half plate, LC plus reflector. The display with optimized cell parameters shows high contrast ratio (CR) over 130 with high light efficiency over 90% at normal direction and the CR greater than 5 exists over 60$^{\circ}$ of polar angle in all directions.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.12
• /
• pp.2276-2280
• /
• 2008

In this paper, we present thermal dependancy of LED package element by changing temperature of MCPCB for design high efficiency LED lamp, and confirmed influence of LED chip against temperature with analysis of thermal resistance and thermal capacitance. As increasing temperature, WPOs were decreased from 25 to 22.5 [%] and optical power were also decreased. that is decreased reason of optical power that forward voltage was declined by decrease of energy bandgap. Therefore optical power by temperature of MCPCB should consider to design lamp for street light and security light. Moreover, compensation from declined optical efficiency is demanded when LED package is composed. Also, thermal resistances from chip to metal PCB were decreased from 12.18 to 10.8[$^{\circ}C/W$] by changing temperature. Among the thermal resistances, the thermal resistance form chip to die attachment was decreased from 2.87 to 2.5[$^{\circ}C/W$] and was decreased 0.72[$^{\circ}C/W$] in Heat Slug by chaning temperature. Therefore, because of thermal resistance gap in chip and heat slug, reliability and endurance of high power LED affect by increasing non-radiative recombination in chip from heat.

• Journal of Broadcast Engineering
• /
• v.21 no.4
• /
• pp.538-551
• /
• 2016

At the on-site of broadcasting production, the light source of tungsten halogen has been used as a primary light source for representing video images. Although tungsten halogen light has drawn attention in terms of the color reproducibility which is more similar to the sun light than that of other light sources, meanwhile it had problems in energy efficiency. Recently, the LED light source with high efficiency and long lifetime of the energy source has started getting attention as a substitute light source at the broadcast field. Because of the unique light emission principles, compared with tungsten halogen, LED light source has different characteristics in the quality of the light projected from the light source and color reproduction of the video image through a camera. These characteristics cause the delayed introduction of the LED as the broadcast light source. In this study we measured the quality characteristics of the flatness of the color reproduction and light of the LED light source and will present the experimental data whether it is suitable as the broadcasting light source compared to a reference light source of tungsten halogen. In addition, we suggested the future challenges and standards which are needed to expand usage of LED as a broadcast light source.

• Journal of Environmental Science International
• /
• v.28 no.5
• /
• pp.521-526
• /
• 2019

In this study, a solar light collector that collects and transmits solar light required for crop production in a closed plant production system was developed. The solar light collector consisted of a Fresnel lens for collecting solar light, and a tracking actuator for tracking solar light from sunrise to sunset to increase the light collection efficiency. The optical fiber that transmitted solar light was made of Glass Optical Fiber (GOF), and it had an excellent optical transmission rate. After collecting the solar light, the amount of light was measured at 5, 10, 15, 20, 25, and 30 cm distances from the GOF through the darkroom by using a light sensor logger connected to a quantum and pyranometer sensor. Compared with solar light, the light intensity of pyranometer sensor measured at 5 cm was 114% higher than solar light, and 61% at 10 cm. In addition, it was observed that it is possible to transmit the necessary amount of light for growing crops up to about 15 cm (as over 22%) through GOF. Therefore, adding diffusers to the solar light collector should be expected to replace artificial light in plant factories or plug seedlings nurseries for leafy vegetables. More studies on the solar light collection devices and the light transmission devices that have high light collection efficiency should be conducted.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.140-146
• /
• 2020

We investigated light extraction film based on polymer dispersed liquid crystal (PDLC) for application in organic light emitting diodes (OLEDs). At least 30 seconds of direct UV irradiation process for curing PDLC film on a bottom-emitting OLEDs was successfully achieved without damage on the intrinsic properties of the OLED. We demonstrated that high haze and transmittance can be tuned simultaneously by controlling the UV curing time. By adding PDLC as an external layer without any additional treatment, the light scattering and extraction is increased. Consequently, a PDLC scattering film with 89.8% and 59.9 of total transmittance and haze respectively, achieved about 16% of light intensity enhancement from integrating sphere measurement.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.5
• /
• pp.427-431
• /
• 2011

Hybrid $SiO_2-TiO_2$ photoelectrode with different type of layers was investigated in dye-sensitized solar cells (DSSC). Use of a thin layer of nanocrystalline $TiO_2$ would imply reduction in the amount of dye coverage, however, lower amount of dye in the thin films would imply fewer electron generation upon illumination. So, thus, it becomes necessary to include a $SiO_2-TiO_2$ layer for increase light harvesting effect such that the lower photon conversion due to thin layer could be compensated. In this paper reports the use of transparent high surface area $TiO_2$ layer and an additional $SiO_2-TiO_2$ layer, thus ensuring adequate light harvesting in these devices. The best solar conversion efficiency 6.6% under AM 1.5 was attained with a multi-layer structure using $TiO_2$ layer/$SiO_2-TiO_2$ layer/$TiO_2$ layer for the light harvesting and this had resulted to about 44% increase in photocurrent density of dye-sensitized solar cells.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.9
• /
• pp.1-10
• /
• 2002

We have done various treatments of indium tin oxide (ITO) surface for organic light-emitting diodes (OLEDs), and investigated the surface states by different surface treatments using atomic force microscopy (AFM) and Auger electron spectroscopy (AES). We have fabricated OLEDs deposited by ultra-high vacuum molecular beam deposition system and studied the characteristics of the OLEDs. We have observed the dramatical improvement of the performance of OLEDs fabricated on ITO substrates treated by $O_2$ plasma treatment reduces the carbon comtamination of ITO surfaces and increases the work function of ITO.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.30 no.3
• /
• pp.21-29
• /
• 2016

In this paper, optical tracking and analysis was carried out to find the optical properties with respect to various geometric design parameters of collimator lens which is very efficient when collect the light. As a result, a whole, ellipse incident part can obtain a high light efficiency and a narrow beam angle, and angled cylinder incident part is confirmed to obtain high efficiency and a narrow beam angle at a certain height or more. When Transmission part have a specific surface which can reflect the light in forward direction, a good optical properties was confirmed.