• Korean Journal of Materials Research
• /
• v.33 no.4
• /
• pp.159-163
• /
• 2023

Zinc-ion Batteries (ZIBs) are currently considered to be effective energy storage devices for wearable electronics because of their low cost and high safety. Indeed, ZIBs show high power density and safety compared with conventional lithium ion batteries (LIBs) and exhibit high energy density in comparison with supercapacitors (SCs). However, in spite of their advantages, further current collector development is needed to enhance the electrochemical performance of ZIBs. To design the optimized current collector for high performance ZIBs, a high quality graphene film is suggested here, with improved electrical conductivity by controlling the defects in the graphene film. The graphene film showed improved electrical conductivity and good electron transfer between the current collector and active material, which led to a high specific capacity of 346.3 mAh g^-1 at a current density of 100 mA g^-1, a high-rate performance with 116.3 mAh g^-1 at a current density of 2,000 mA g^-1, and good cycling stability (68.0 % after 100 cycles at a current density of 1,000 mA g^-1). The improved electrochemical performance is firmly because of the defects-controlled graphene film, leading to improved electrical conductivity and thus more efficient electron transfer between the current collector and active material.

• Current Applied Physics
• /
• v.18 no.12
• /
• pp.1534-1539
• /
• 2018

SnSe single crystal showed a high thermoelectric zT of 2.6 at 923 K mainly due to an extremely low thermal conductivity $0.23W\;m^{-1}\;K^{-1}$. It has anisotropic crystal structure resulting in deterioration of thermoelectric performance in polycrystalline SnSe, providing a low zT of 0.6 and 0.8 for Ag and Na-doped SnSe, respectively. Here, we presented the thermoelectric properties on the K-doped $K_xSn_{1-x}Se$ (x = 0, 0.1, 0.3, 0.5, 1.5, and 2.0%) polycrystals, synthesized by a high-temperature melting and hot-press sintering with annealing process. The K-doping in SnSe efficiently enhances the hole carrier concentration without significant degradation of carrier mobility. We find that there exist widespread Se-rich precipitates, inducing strong phonon scattering and thus resulting in a very low thermal conductivity. Due to low thermal conductivity and moderate power factor, the $K_{0.001}Sn_{0.999}Se$ sample shows an exceptionally high zT of 1.11 at 823 K which is significantly enhanced value in polycrystalline compounds.

• Composites Research
• /
• v.19 no.2
• /
• pp.7-12
• /
• 2006

Graphite particle/carbon fiber hybrid conductive polymer composites were fabricated by the compression molding technique. Graphite particles were mixed with an epoxy resin to impart the electrical conductivity in the composite materials. In this study, graphite reinforced conductive polymer composites with high filler loadings were manufactured to accomplish high electrical conductivity above 100S/cm. Graphite particles were the main filler to increase the electrical conductivity of composites by direct contact between graphite particles. While high filler loadings are needed to attain good electrical conductivity, the composites becomes brittle. So carbon fiber was added to compensate weakened mechanical property. With increasing the carbon fiber loading ratio, the electrical conductivity gradually decreased because non-conducting regions were generated in the carbon fiber cluster among carbon fibers, while the flexural strength increased. In the case of carbon fiber 20wt.% of the total system, the electrical conductivity decreased 27%, whereas the flexural strength increased 12%.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.6
• /
• pp.93-99
• /
• 2012

A nanofluid is a fluid containing suspended solid particles, with sizes on the order of nanometers. Especially graphene nanoparticle that has the high thermal conductivity properties among the various nanoparticles added to the nanofluid is receiving attention. Graphene is a flat monolayer of $sp^2$-bonded carbon atoms tightly packed into a honeycomb lattice. And are known to have very high thermal conductivity. Therefore, we compared thermal conductivity with viscosity of graphene M-5 nanofluids and graphene M-15 nanofluids. Graphene M-5 and graphene M-15 have different average particle diameters and the other properties are the same. Two kinds of graphene nanofluids was examined by measuring thermal conductivity via transient hot-wire method. And the viscosity was measured by using a rotational digital viscometer. As a result, graphene M-5 nanofluids exhibited better thermal conductivity and viscosity than graphene M-15 nanofluids.

• Polymer(Korea)
• /
• v.27 no.3
• /
• pp.201-209
• /
• 2003

DC and AC electrical conductivity and electromagnetic interference shielding effectiveness of milled carbon fiber/nylon composites were investigated with the kind of nylon matrix. Percolation transition at which the conductivity is sharply increased was observed at about 7 vol% of milled carbon fiber. Nylon 46 as a matrix was more effective to obtain high electrical conductivity than nylon 6, and the difference in conductivity was occurred by the treatment of coupling agent. Frequency dependence of AC conductivity could be explained by relaxation phenomenon at just below percolation and resonance phenomenon at 40 vol% of carbon fiber, respectively. Negative temperature coefficient phenomenon was found in all composites. Electromagnetic interference shielding effectiveness was increased with the concentration of carbon fiber. At a high conductivity region the return loss was more dominant to the total shielding effectiveness than the absorption loss.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.31 no.2
• /
• pp.92-103
• /
• 1989

This study was performed in order to produce the basic data for devising irrigation project and desalinization countermeasure through analyzing salt movement and desalinzation effects. The Desalinization experiments with water management practices were carried out, using the soil samples collected in New Manguem tideland. The changes of electrical conductivity, exchangeable sodium percentage, pH and hydraulic conductivity during the desalinization experiments, and the correlations between various factors influencing desalinization, were analyzed by the statistical method. The results obtained from this study were summarized as follows: 1. The sample soils used in this study were salin-sotlic soils with the high electrical conductivity and the high exchangeable sodium percentage, and the soil texture was silt loam. 2. A large amount of the soluble salts was removed in the begining of desalinization experiments. The initial electrical conductivity and the initial exchangeable sodium percentage decreased considerably in the beginning, and were gradually slow in the rate of decrease 3. The value of pH showed a tendency to increase during the desalinization and were little by little slow in the rate of increase, and could be estimated by the regression equation. 4. The initial hydraulic conductivity were raised greatly with gypsum treatment and the penmeability was maintained adequately, The hydraulic conductivity and the leaching time elapsed during the desalinization could be estimated by the regression equation. 5. The water requirement for desalinization with various water management practices could be estimated for a given electrical conductivity, exchangeable sodium percentage, and pH reading respectively.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.21 no.2
• /
• pp.225-234
• /
• 2023

In the design of HLW repositories, it is important to confirm the performance and safety of buffer materials at high temperatures. Most existing models for predicting hydraulic conductivity of bentonite buffer materials have been derived using the results of tests conducted below 100℃. However, they cannot be applied to temperatures above 100℃. This study suggests a prediction model for the hydraulic conductivity of bentonite buffer materials, valid at temperatures between 100℃ and 125℃, based on different test results and values reported in literature. Among several factors, dry density and temperature were the most relevant to hydraulic conductivity and were used as important independent variables for the prediction model. The effect of temperature, which positively correlates with hydraulic conductivity, was greater than that of dry density, which negatively correlates with hydraulic conductivity. Finally, to enhance the prediction accuracy, a new parameter reflecting the effect of dry density and temperature was proposed and included in the final prediction model. Compared to the existing model, the predicted result of the final suggested model was closer to the measured values.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.248-251
• /
• 2005

Graphite reinforced conductive polymer composites for PEMFC bipolar plates were fabricated by the compression molding technique. Graphite powder was mixed with an phenol resin to impart electrical property in composites. In this study, conductive polymer composites with high filler $loadings(>60wt.\%)$ were manufactured to accomplish high electrical conductivity above 100S/cm. The level of compaction is important because graphite powder increase electrical conductivity of composites by direct physical contact between particles. The optimum molding pressure according to filler was proposed experimentally. Various tests(electrical conductivity, flexural strength, compressive strength, leach test, etc) were carried out to verify the performance of fabricated composites for PEMFC bipolar plates. Fabricated composites have good electrical conductivity and mechanical strength. The results of leach test and contact angle measurement showed similar characteristics compared with commercial bipolar plates.

• Macromolecular Research
• /
• v.11 no.6
• /
• pp.458-466
• /
• 2003

Several copolyimides have been synthesized with different combinations of comonomers in order to study the relationship between conductivity and water insolubility. m-Phenylenediamine (m-PDA), an angled comonomer, was introduced into the polymer backbone to increase water absorption, and resulted in higher proton conductivity. 2,2-bis(trifluoromethyl)benzidine (TFMB) was used as the comonomer to promote water insolubility. There is a good correlation between the water uptake and conductivity of the polyimides. The copolyimides that had high water uptake also generated high proton conductivity. Those polyimides had good mechanical properties. The copolyimides that have 27 mol% of TFMB and 9 mol% of m-PDA have reasonable conductivities and are insoluble in water at 90$^{\circ}C$, even though they have lower conductivities than those of the homopolymer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.234-237
• /
• 1996

The amorphous chalogenide semiconductors are new material in semiconductor physics. Their properties, especially electronic and optical properties are main motives for device application. Amorphous As$_{10}$Ge$_{15}$ Te$_{75}$material has the stable ac conductivity at high frequency and the dc memory switching property. At higher frequency than 10MHz, ac conductivity of As$_{10}$Ge$_{15}$ Te$_{75}$ thin film is much higher than below frequency and independent of temperature and frequency. If the dc voltages are applied between edges of thin film, one can see the dc memory switching phenomenon, in other words the dc conductivity increases quite a few of magnitude after the threshold voltage is applied. Using the stable ac conductivity at high frequency and the increase of conductivity after dc memory switching, As$_{10}$Ge$_{15}$ Te$_{75}$thin film is considered as new material for microwave switch devices.vices.es.vices.