• Journal of Power System Engineering
• /
• v.15 no.1
• /
• pp.39-44
• /
• 2011

This study was to investigate the effects of stress ratio and anisotropy on Fatigue Crack Propagation(FCP) behavior of rolled magnesium alloy AZ31B. The experimental materials were a Mg-Al-Zn magnesium alloy. The FCP test was conducted on compact tension specimen by a servo-hydraulic fatigue testing machine in air at room temperature. Compact tension specimens were prepared from the extruded parallel and vertical rolling direction. The test condition was frequency of 10Hz and sinusoidal load stress ratios are 0.1 and 0.7. The FCP rates was automatically measured by a compliance method. In the case of the FCP of AZ31B, the FCP of both direction of LT and TL by anisotropy of specimens are almost same value. In lower stress ratio, the FCP of the LT, TL specimens are increased in lower ${\Delta}K$ region but higher ${\Delta}K$ regions are almost same value. Finally, the result of observed the surface crack, it expressed the quasi-cleavage fracture in lower ${\Delta}K$ region and straight mark on the aspect of the facet in high ${\Delta}K$ region.

• Journal of Korean Society for Atmospheric Environment
• /
• v.22 no.2
• /
• pp.223-233
• /
• 2006

We analyzed the monthly and seasonal mean of the daily Erythemal Ultraviolet-B (EUV-B, $280{\sim}320nm$) irradiance operating in Pohang, Anmyeon, Gosan, Mokpo and Kangnung with UV-Biometer (Solar Light Co., Model No. 501) at clear-sky noon during the period from 1999 to 2004. Also, we investigated the seasonal and regional characteristics for the UV index over the Korean Peninsula. The daily maximum occurred near solar southing time and the highest monthly accumulated EUV-B irradiance appeared in July and August at each regional observatory. The monthly mean value of the clear-sky EUV-B irradiance in Pohang, Anmyeon, Gosan, Mokpo and Kangnung showed 196.6, 161.8, 221.9, $171.5mWm^{-2}\;and\;179.7mWm^{-2}$ near noon in July respectively. The annual mean value of the daily accumulated EUV-B irradiance in Pohang, Anmyeon, Gosan, Mokpo and Kangnung were 1.8, 2.1, 2.2, $1.8kJm^{-2}\;and\;1.5kJm^{-2}$ respectively. The UV Index (UVI) showed above UVI 7(High) more than 90 days during one year over the Korean Peninsula.

• Korean journal of food and cookery science
• /
• v.23 no.1 s.97
• /
• pp.99-106
• /
• 2007

This study investigated the effect of UV-B irradiation on the quality of Pleurotus ostreatus. The changes of vitamin $D_2$ contents, color value and flavor pattern in mushrooms were analyzed by high-performance liquid chromatography (HPLC), chromameter and gas chromatography - surface acoustic wave (GC-SAW) electronic nose. By exposure to UV-B irradiation (0 kj/m$^2$, 10 kj/m$^2$, 20 kj/m$^2$), vitamin $D_2$ content increased from 0 (control) to 48.50 g/g (DM: dry matter, 10 kj/m$^2$) and 61.58 g/g (DM, 20 kj/m$^2$). Although there was no significant difference in L, a, b values among the three groups, flavor changes were detected by GC-SAW electronic nose. The number of peaks increased from 10 in the control group (0 kj/m$^2$), to 14 and 15 for the 10 kj/m$^2$ and 20 kj/m$^2$ groups, respectively. Nevertheless, the changes of flavor pattern were not detrimental to the mushroom quality. These results suggested that UV-B irradiation is an effective method to increase the vitamin $D_2$ content without degrading the quality.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.37 no.2
• /
• pp.121-127
• /
• 2011

Skin darkness is the source of trouble to many women. Skin darkness is the state that while skin redness and brightness are reduced, skin yellowness is increased. Skin translucency which is measured by skin color, especially brightness is an another expression of skin darkness. Skin brightness is usually expressed by L value of $L^{*} \;a^{*}\; b^{*}$ (CIELAB color space system). However, it is hard to find the relationship between L value and perceptive efficacy such as translucency because the L value is just a factor of evaluation of skin darkness. The skin with high translucency has high scattering reflective light value than low value. In this study, we measured the skin translucency of 20 ~ 30 ages men and women face by both our designed previous device which use polarized light to detect surface and scatter reflective light independently and $Lumiscan^{TM}$ which is improved designed to confirm our new device working ability by calculation of relationship between trnaslucency and scattering reflective light value. The result of this study indicate that there is a high correlation (R = 0.732, p < 0.01) between translucency and scattering reflective light value, and suggest that $Lumiscan^{TM}$ is portable and easy measuring device more that previous device.

• KSBB Journal
• /
• v.28 no.1
• /
• pp.60-64
• /
• 2013

Two strains were isolated from the traditional Deep Blue Sediment Dye of Polygoum tinctoria, Niram, and temporarily named Niram A and Niram B, respectively. The phylogenetic analysis revealed that strain Niram A and B were closely related to the members of the genus Comamonas and Microbacterium, respectively. Strain Niram A exhibited the highest 16S rRNA gene sequence similarity to C. aquatica LMG $2370^T$ (98.06%). Strain Niram B showed 100% homology with M. oxydans DSM 20578T and M. maritypicum DSM $12512^T$. The growth of the strain Niram A and B was not inhibited in Niram medium containing high calcium concentration without free sugar as carbon source. The reducing Niram is greenish. Therefore, the reducing ability on the Niram of the strains Niram A and B were determined with the color difference of the $a^*$ values of Niram fermented-fluids. The $a^*$ value indicates the level of redness (positive value) or greenness (negative value). The green color is increasing towards the negative value. In all samples fermented for 10 days, the $a^*$ values among samples were no significant difference. However, samples fermented for 15 days have an appreciable change. After fermentation for 15 days, the control Niram sample had $-3.96{\pm}0.02$ of the $a^*$ value. On the other hand, the Niram samples fermented with the strain Niram A and B showed $-4.20{\pm}0.02$ of the $a^*$ value and $-7.86{\pm}0.03$ of the $a^*$ value, respectively. In the reducing ability on the Niram, the strain Niram B was significantly better than the strain Niram A.

• Journal of the Korea Institute of Building Construction
• /
• v.3 no.4
• /
• pp.79-86
• /
• 2003

The purpose of study is to offer base data for high fluid concrete mix property, as grasp effect of aggregate to reach much more effect for producing high fluid concrete. For this study, there are three types of combined aggregates, river sand + river aggregate(type A), river sand + crusted aggregate(type B), washed sea sand + crushed aggregate(type C) and take a factor, water-contents, water-binder ratio and S/a. And so, we had following conclusion, resulting application-ability of high fluid mortar by K-slump tester to use a handy consistency measuring instrument. And so, we had following conclusion, resulting application-ability of high fluid concrete by K-slump tester to use a handy consistency measuring instrument. 1) In cafe of regular water binder ratio, high fluid concrete suffered much effect of combined aggregates and water binder ratio. Range of water binder ratio by combined aggregates is w/b 0.4 downward(type A and B), w/b 0.35 downward(type C). 2) Water contents to need for producing high fluid concrete is minimum 170kg/$\textrm{m}^3$ without regard to combined aggregates. 3) The effect of S/a on high fluid concrete by combined aggregates is approximately S/a 50% (type A and B), s/a 50-55% (type C). 4) Consistency measuring of high fluid concrete by K-slump tester is possible and first indication value, high fluid concrete can be produced, is 6~10.5cm.

• Journal of KSNVE
• /
• v.6 no.3
• /
• pp.349-355
• /
• 1996

For a rail traffic noise, a typical source has a length of 200m - 400m so that the noise pollution areas have been located in the transition regions where the sound level drops between 3dB/dd and 6dB/dd. Therefore, in this region, parameters such as a horizontal distance from the track, the geometry of the ground surface, the environmental effect, and the boundary impedance condition play import roles, especially in our nation's situation. In this study, modelling techniques for the finite length of noise source have been investigated in order to evaluate the rail traffic noise level. Then. noise correction value .${\Delta}$SPL for various location in the track region is represented by the non-dimensionalized horizontal and parallel distance from the track. As an application, a high speed train is examined. Beas on the noise data measured for a Eurostar in France, the sound power value per unit length $H_1$is calcuated. It turns out that$H_1$is 109 dB. Overall sound power from the highspeed train to be serviced in our country is expected to 135 dBA.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.2
• /
• pp.173-180
• /
• 2014

The development process of a L-Band microwave radiometer for remote sensing of soil-moisture are described in this paper. Achieving the development aim of the measurement accuracy within 2% for soil moisture content of 0~50%, the requirements and specifications of the microwave radiometer and its receiver are drawn. The receiver with high gain, high sensitivity is designed and implemented to satisfy these requirements and specifications. The receiver has the bandwidth of 40 MHz, the system gain of 50 dB and the sensitivity of average value 0.19 K, maximum value 0.313K at 1390 MHz.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.315-317
• /
• 2002

The value of I$_{c}$(critical current) in HTS (High Temperature Superconducting) tape has a great influence on B(equation omitted) (magnetic field amplitude applied perpendicular to the tape surface). Therefore, I$_{c}$ of HTS magnet is determined by not only operating temperature but also the B(equation omitted). In shape design of field coil for the HTS motor, a method to reduce the B(equation omitted) and to determine operating current should be considered in order to optimal design. On the basis of the magnetic field analysis, this paper deals with various field coil shape to obtain operating current of HTS motor by using analytical method. And also this paper discusses the operating current of 100hp class HTS motor by using I$_{c}$-B(equation omitted) curve.curve.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.142-142
• /
• 2017

High Flory-Huggins interaction parameter (${\chi}$)를 가지는 polystyrene-block-dimethylsiloxane (PS-b-PDMS)는 초미세 패턴 제작과 우수한 defect density, 우수한 edge roughness 특성으로 향상된 패턴을 제공한다는 점에서 반도체 분야에서 많은 연구가 되고 있다. 하지만, PS와 PDMS 사이에 존재하는 큰 surface tension의 차이로 인해 PDMS는 PS와 air 사이에서 segregate되기 때문에 수직배향에 불리하여 high aspect ratio (HAR)을 가지는 cylinder, lamellar 패턴 제작에 있어 큰 어려움을 가진다. 본 연구에서는 이러한 문제를 해결하기 위해, PS-b-PDMS BCP 패턴과 하부 실리콘 기판 사이에 amorphous carbon layer (ACL)를 삽입하여 효과적으로 pattern transfer하는 공정을 연구하였다. 플라즈마를 이용하여 무한대에 가까운 etch selectivity를 가지는 식각 공정을 개발함으로써 낮은 aspect ratio를 가지는 PS-b-PDMS BCP 패턴의 한계점을 극복하였다. Large-x value를 가지는 BCPs를 이용하여도 매우 높은 aspect ratio를 가지면서 동시에 pattern quality를 향상시킬 수 있는 plasma process를 제시하였다.