• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.6
• /
• pp.500-506
• /
• 2012

In this paper, a non-isolated high step-up and high efficiency boost converter is proposed. By using the 3-level boost converter structure, the proposed converter can obtain higher voltage gain than conventional high step-up converters. The voltage spike of the switching device is well clamped by using the clamp circuit composed of a clamp diode and a capacitor and the energy of the leakage inductor of coupled inductor is effectively transferred to output. Due to the 3-level structure, the equivalent switching frequency of the coupled inductor is doubled, which results in reduced inductor size. A 500 W prototype converter is built and tested to verify performance of the proposed converter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.5
• /
• pp.372-378
• /
• 2019

This study proposes a new zero-current-zero-voltage-transition (ZCZVT) boost-flyback converter using a soft switching auxiliary circuit. The proposed converter integrates the boost and flyback converters to increase the voltage with a low duty ratio. The main and auxiliary switches turn the ZCZVT conditions on and off. Thus, the proposed converter has high efficiency. The voltage gain at the steady state is derived, and the inductor volt-second balance and the design guidelines are presented. Finally, the performance of the proposed converter is validated by experimental results from a 200 W, 30 V DC input, 400 V DC output, and 200 kHz boost-flyback converter prototype.

• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.34-43
• /
• 2019

An improved half-bridge LLC converter with a magamp auxiliary post-regulator is proposed in this paper. The function of the magamp is bypassed when the converter works within the low input-voltage range. Meanwhile, it operates as an auxiliary post-regulator when the input voltage is high. By changing the blocking time of the magamp, the dc gain of the converter can be extended. Hence, the input voltage range of the converter is extended. The realization of proposed topology does not require a complicated circuit. The controller of the magamp can be easily implemented using only passive components, transistors and an OP amp. The generalized operational principle is analyzed and the design criterion for the magamp is presented. Finally, a 25V output, 400W experimental prototype was built and tested for a 160-300V input-voltage range to verify the feasibility of the proposed method.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.272-277
• /
• 1990

A soft switched matrix converter is proposed by adopting the zero voltage switching technique being used in some resonant pole inverters. High operating frequency with safe and efficient switching improves dynamic and spectral performances and simplifies protection logics and snubber networks. Further, it can be implemented using simple analog circuits, having similar transfer characteristics to those of the modern pulse width modulated matrix converters such as, maximum voltage transfer ratio and unity input displacement factor. Analyses, design and simulation results are presented to verify the operating principle.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.596-599
• /
• 1991

This paper describes a novel switching algorithm of series connected power semiconductors for high voltage applications. In order to improve the reliability and efficiency of high voltage static power converters, we study on the switching characteristics of series connected power semiconductors and then propose "a servo control of snubber capacitor value" for the dynamic voltage balancing under turn-off state in series connected power semiconductors. Finally, we illustrate the validity of this algorithm by computer simulation and experimental results.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.476-477
• /
• 2008

In this paper, high voltage DC- DC boost converters by stacked structure of power transistors are proposed. These stacked power transistors are tolerant to output voltage higher than the process limit for individual CMOS transistors. The proposed circuits were designed in a standard 3.6V, $0.13{\mu}m$.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.10
• /
• pp.148-156
• /
• 1996

Increasing the switching frquency is essential to achieve the high density of switched mode power supplies, but this leads to the increase of switching losses. A number of new soft switching converters have been presented ot reduce switching losses, but most of them may have some demerits, such as the increase of voltage/current stresses and high conduction losses. To overcome these problems, the ZVT-PWM converter has recently been presented. in this paper, the operation characteristics of the ZVT-PWM boost converter is analyzed, and the steady-states (DC) and small-signal model of this converter are derived and analyzed, and then the transfer functions of this converter are derived. The transfer functions of ZVT-PWM boost converter are similar to those of the conventional PWM boost converter, but the transfer characteristics are affecsted by te duty ratio and the switching frequency.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2294-2305
• /
• 2016

The introduction of a high-voltage direct-current (HVDC) system based on a modular multilevel converter (MMC) for wind farm integration has stimulated studies on methods to control this type of converter. This research article focuses on the control of the AC voltage and circulating current for a wind-farm-side MMC (WFS-MMC). After theoretical analysis, emotional learning (EL) controllers are proposed for the controls. The EL controllers are derived from the learning mechanisms of the amygdala and orbitofrontal cortex which make the WFS-MMC insensitive to variance in system parameters, power change, and fault in the grid. The d-axis and q-axis currents are respectively considered for the d-axis and q-axis voltage controls to improve the performance of AC voltage control. The practicability of the proposed control is verified under various conditions with a point-to-point MMC-HVDC system. Simulation results show that the proposed method is superior to the traditional proportional-integral controller.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.413-414
• /
• 2014

This paper proposed an optimized design of a dual active bridge converter for a low-voltage charger. The dual active bridge converter among various bi-directional DC/DC converters is a high-efficiency isolated bi-directional converter. In the general design, when the battery voltage is high, the ZVS region is reduced. In contrast, when the battery voltage is low, the efficiency is low due to high conduction loss. In order to increase the ZVS region and the power conversion efficiency, depending on the battery voltage, variable switching frequency method is applied. At the same duty, the same power is obtained regardless of the battery voltage using the variable switching frequency method. The proposed method was applied to a 5kW prototype converter, and the experimental results were analyzed and verified.

• Journal of Power Electronics
• /
• v.14 no.2
• /
• pp.203-216
• /
• 2014

In the conventional dc-dc converter, a pair of additional diode and the adjacent passive component capacitor/inductor can be added to the circuit with an X-shape connection, which generates a family of new topologies. The novel circuits, also called diode-assisted dc-dc converter, enhance the voltage boost/buck capability and have a great potential for high step-up/step-down power conversions. This paper mainly investigates and compares conventional dc-dc converter and diode-assisted dc-dc converter in wide range power conversion from the aspects of silicon devices, passive components requirements, electro-magnetic interference (EMI) and efficiency. Then, a comprehensive comparison example of a high step-up power conversion system was carried out. The two kinds of boost dc-dc converters operate under the same operation conditions. Mathematical analysis and experiment results verify that diode-assisted dc-dc converters are very promising for simultaneous high efficiency and high step-up/step-down power conversion in distributed power supply systems.