• 한국분무공학회지
• /
• 제11권4호
• /
• pp.212-219
• /
• 2006

The initial film flow development of the high-pressure swirl spray was investigated at different injector operating conditions to analyze film flow development and to provide the input data for the modeling works. This result can be also useful to verify the previously simulated results. The initial flow conditions such as liquid film thickness, flow angle and flow divergence are obtained by visualizing the inside and near the nozzle flow with a microscopic imaging system. The visualized images are quantified using an image processing tool. From the information of liquid film thickness and flow angle, the initial axial and tangential velocity and the swirl number of the swirl spray are successfully determined at various operating conditions. The experimental results showed that the initial liquid film thickness, flow angle and flow divergence are remained constant when the injection pressure is increased. However, initial film conditions are severely changed when the fuel temperature is increased. The swirl number remained constant when the injection pressure is increased while it showed increased value at high fuel temperature condition.

• 한국가스학회지
• /
• 제12권2호
• /
• pp.12-17
• /
• 2008

강화되는 배출가스 규제에 대응하기 위한 대책으로 LPG 차량에 적용되고 있는 제3세대 LPG 연료공급방식인 LPLi(Liquid Phase LPG Injection)은 LPG 연료를 펌프를 이용해서 고압의 액상연료를 공급하는 것이 가장 핵심적인 기술이다. 그러나 LPG 연료의 경우 저점도, 저비등점의 물리적 특성을 갖는 가스연료로서 기존의 가솔린 또는 디젤용 펌프를 사용할 경우 성능 및 효율이 달라질 수 있다. 본 연구에서는 가솔린 연료 펌프의 임펠라 방식을 응용 변형시켜서 LPG연료용으로 개발된 펌프를 이용하여 다양한 온도와 연료조성 조건에서 초기토출성능 및 효율을 파악하고, 기존 펌프의 단점을 극복할 수 있는 펌프방식의 적용가능성 여부를 판단하고자 한다.

• 한국연소학회지
• /
• 제20권4호
• /
• pp.26-33
• /
• 2015

American NREL (National Renewable Energy Laboratory) reported that BD20 could reduce PM, CO, SOx and cancerogenic matters by 13.6%, 9.3%, 17.6% and 13% respectively, compared to diesel fuel. BD20 has been being tested on garbage trucks and official vehicles at Seoul City, which is positive on air environment, but negative on combustion by higher viscosity in winter season. This study investigated the combustion characteristics by employing multi cavity piston for improving the deterioration of combustibility caused by the higher viscosity of the biodiesel fuel such as BD20 with the combustion flames taken by a high speed camera and the cylinder pressure diagram. A 4-cycle single cylinder diesel engine was remodeled to a visible 2-cycle engine for taking the flame photographs, which has a common-rail injection system. The test was done at laboratory temperature of about $4{\sim}5^{\circ}C$.

• 한국자동차공학회논문집
• /
• 제12권4호
• /
• pp.24-30
• /
• 2004

As the environmental pollution becomes serious global problem, the regulation of emission exhausted from automobiles is strengthened. Therefore, it is very important to know how to reduce the NOx and PM simultaneously in diesel engines, which has lot of merits such as high thermal efficiency, low fuel consumption and durability. By this reason, the new concept called as Homogeneous Charge Compression Ignition(HCCI) engines are spotlighted because this concept reduced NOx and P.M. simultaneously. However, there is trade off between output and NOx in a HCCI engine. In this study, output and emission characteristics for a gasoline direct injection type HCCI engine were investigated to clarify the effects of intake air temperature, injection time and mixture formation. From these experiments, we found that the smoke was not produced when the fuel was injected earlier than BTDC 90$^{\circ}$. In addition, the output was increased because of delay of ignition time and NOx emission was decreased because of homogeneous charge of first injection in case of split injection.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 제26회 KOSCO SYMPOSIUM 논문집
• /
• pp.7-12
• /
• 2003

The purpose of this work is to investigate the effect of premixing condition on the combustion and exhaust emission characteristics in a HCCI diesel engine. To form homogeneous charge before intake manifold, the premixed fuel is injected into premixed tank by GDI injection system and the premixed fuel is ignited by direct injected diesel fuel. But in the case of high intake air temperature, premixed fuel is auto-ignited before diesel combustion and soot emission is increased. In the case of light load condition, the BSFC is improved by intake air heating because increased air temperature promoted the combustion of premixed mixture. NOx and smoke concentration of exhaust emissions are reduced compared to conventional diesel engine. The combustion characteristics of the HCCI diesel engine such as combustion pressure, rate of heat release, and exhaust emission characteristics are discussed.

• 한국연소학회지
• /
• 제4권1호
• /
• pp.95-103
• /
• 1999

Experimental study on combustion characteristics of a regenerative combustor has performed. High-temperature air combustion in the regenerative combustor is obtained through heat recovery from exhaust gas flow by porous ceramic materials and through alternation of air flow direction through the combustor. Temperature field, CO and NOx emission with respect to the frequency of alternation are measured. It is found that at initial stage of the alternation, temperature of inlet section of main combustion chamber is increased sharply since both high temperature air preheated by the ceramics and prompt fuel injection results in rapid combustion. Following this initial stage, combustion temperature is reduced as the preheated air temperature is reduced. However peak temperature in the chamber and exhaust gas temperature are decreased as the alternation period is reduced, increased temperature of ceramic is observed. CO and NOx emission with respect to the alternation period is also examined. It is found that there exists a range of optimum alternating period for CO and NOx emission characteristics.

• 한국표면공학회지
• /
• 제52권1호
• /
• pp.43-51
• /
• 2019

The environmental pollution which is global warming and abnormal climate is caused by increasing population and activated economics. To reduce environmental pollution, we have being efforts into reducing $CO_2$ emission and use of energy, resources. Especially, for the sake of light weight and fuel efficiency of automotive industry, many countries have defined the restrict environmental regulation which stipulate high magnitude of reducing $CO_2$ emission. In this study, we have predicted the problem of Mu-cell injection molding through the finite element analysis as a function of temperature controlled by Joule heating or in terms of mold temperature. From the result of finite element analysis, we have determined the optimized process and made the injection mold included electric current heating system with Mu-cell manufacturing. Lastly, we analyzed the surface characteristics of the injection products with mold temperature.

• 한국연소학회지
• /
• 제3권1호
• /
• pp.59-69
• /
• 1998

The results of study on the active control of naturally occurring combustion oscillations with a single dominant frequency in an atmospheric dump combustor are presented. Control was achieved by an oscillatory infection of secondary fuel at the dump plane. A high speed solenoid valve with a maximum frequency of 250Hz was used as the actuator and a sound level meter, located at the combustor exit, measured the pressure fluctuations which served as the feedback signal for the control loop. Instability characteristics were mapped over a range of mean mixing section velocities from 6.7 m/s-9.3 m/s and with three mixing conditions. Different fuel/air mixing conditions were investigated by introducing varying percentages of primary fuel at two locations, one at the entrance to the mixing section and one 6 mixing tube diameters upstream of the dump plane. Control studies were conducted at a mean velocity of 9.3 m/s, with an air temperature of $415^{\circ}C$, and from flame blowout to the stoichiometric condition.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2003년도 제21회 추계학술대회 논문집
• /
• pp.173-178
• /
• 2003

슬링거 연소기의 연소특성을 파악하기 위한 연구를 수행하였다. 연료는 고속으로 회전하는 축의 연료노즐을 통하여 연소기내로 분사된다. 회전분무시스템의 분무특성을 파악하기 위하여 PDPA를 이용하여 연료노즐의 회전속도 변화에 따른 분무입자의 크기를 측정하였다. 연구결과 분무액적의 크기는 연료노즐의 회전수와 직접적인 상관관계가 있음을 알 수 있었다. 실물크기의 연소기를 제작하여 한국 항공우주연구원의 연소시험설비에서 점화 및 연소시험을 수행하였다. 시험결과 점화성능 및 연소효율은 연료노즐 회전수에 따라 증가하는 경향을 나타내고 있었으며, 연소기출구온도는 매우 균일한 온도분포를 나타내었다.

• 대한기계학회논문집B
• /
• 제31권3호
• /
• pp.283-291
• /
• 2007

The static pressure distribution, atomization characteristics and velocity distribution of tapered nozzle swirl spray is analyzed and then compared with original swirl spray. The static pressure distribution inside the swirl spray is measured using a piezoresistive pressure transducer. Phase Doppler anemometry (PDA) is applied to measure and analyze the droplet size and velocity distribution of tapered nozzle and original swirl spray. The static pressure inside the spray shows the lower value compared to the atmospheric pressure and this pressure drop is getting attenuated as the taper angle is increased. The droplet size of tapered nozzle spray shows similar value compared to the original swirl spray at the horizontal mainstream while it shows increased value at vertical mainstream. The deteriorated atomization characteristics of tapered nozzle spray is improved by applying high fuel temperature injection without causing the spray collapse. The velocity results show that the larger portion of fuel is positioned with higher injection velocity, and the smaller portion of fuel is positioned with lower injection velocity with causing spatially non-uniform mixture distribution.