• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.5
• /
• pp.85-92
• /
• 2016

The eight mixes and artificial soil aggregates were prepared for evaluating the practical application of lightweight foamed concrete as soil aggregates. The main parameter was unit binder content ranged between from 100 to $800kg/m^3$. In lightweight foamed concrete, flow, slurry and dried density, and compressive strength at different ages were measured. In Artificial soil aggregates crushed from lightweight foamed concrete, particle size distribution, pH, coefficient of permeability, cation exchange capacity(CEC), and ratio of carbon to nitrogen(ratio of C/N), were measured. The test results showed that flow, slurry and dried density, and compressive strength at different ages of lightweight foamed concrete increased with the increasing of unit binder content. Compressive strength at age of 28, of lightweight foamed concrete with unit binder of more than $500kg/m^3$, was more than 4 MPa. The ammonium phosphate immersion time of more than age of 3, was effective to decrease pH of artificial soil aggregates. In addition, artificial soil aggregates was evaluated as high class in terms of cation exchange capacity(CEC), while satisfied with value of ratio of carbon to nitrogen(ratio of C/N) recommended by landscape specification.

• Journal of Plant Biotechnology
• /
• v.33 no.2
• /
• pp.105-110
• /
• 2006

This study was carried out to investigate the effects of plant growth regulators, medium salt strength and nitrogen ratio on cell culture of Gymnema sylvestre. Cell growth was inhibited by 2,4-D higher than 1.0 mg L$^{-1}$, but not by kinetin lower than 0.5 mg L$^{-1}$. Maximal cell growth was obtained at 1.0 mg L$^{-1}$ 2,4-D and 0.1 mg L$^{-1}$ kinetin. Cell growth was greatest at 1x MS medium but high strength of MS medium inhibited cell growth due to low water potential in the medium. In $NH_4^+:NO_3^-$ ratio of 0:60 (i.e. 0.0 mM $^NH_4^+$ and 60.0 mM $NO_3^-$), cells growth was highest but cells were smaller and whiter compared with those in other $NH_4^+:NO_3^-$ ratio. Reduced cell growth was observed with continuous culture. These results suggested that optimal cell culture of G. sylvestre could be achieved with 1x MS medium with 20:40 ratio of $NH_4^+:NO_3^-$ supplemented with 1.0 mg L$^{-1}$ 2,4-D and 0.1 mg L$^{-1}$ kinetin.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.2
• /
• pp.77-84
• /
• 2011

This study was conducted to develop a novel combined system of a hybrid rotating biological contactor (RBC) process that was composed of an attached- and suspended- biomass reactor, followed by a settler and a biological aerated filter (BAF) column to treat a high strength slaughter wastewater. Long term influences of organic and nitrogen loading rates were investigated to see how the combined system worked in terms of the removal efficiency. A synthetic wastewater containing a pork cutlet steak source (commercially available) and swine blood was used to feed the combined system. The hybrid RBC process showed excellent removals: about 95% for soluble COD and 85% for ammonium nitrogen. However, the unsettled solids seriously deteriorated the removal efficiency of total COD (TCOD) and total nitrogen (TN) in the RBC process. A significant fraction of the TCOD and suspended solids (SS) was further removed in the BAF column although the effluent quality was still unsatisfactory, giving TCOD 300 mg/L, SS 180 mg/L and TN 59 mg/L. An addition of polyaluminium chloride into the RBC effluent improved the performance of the settler and BAF, producing an excellent quality of final effluent; TCOD 16.5 mg/L, SS 0 mg/L, TN 55.5 mg/L, TP 1.3 mg/L. Therefore, it was confirmed that the combined system of hybrid RBC and BAF could treat a high strength slaughter wastewater excellently.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 2000.06a
• /
• pp.1-33
• /
• 2000

Silicon carbide ceramics with sintering additives from the system AlN-Y$_2$O$_3$ can be gas-pressure sintered to theoretical density. While commonly a combination of sesquioxides is used such as Al$_2$O$_3$-Y$_2$O$_3$, the oxynitrid additives offer the advantage that only a nitrogen atmosphere is require instead of a powder. By starting form a mixture of ${\beta}$-SiC and ${\alpha}$-SiC, and by performing dedicated heat treatments after densification, anisotropic grain growth is obtained which leads to a platelet microstructure showing enhance fracture toughness. In the present work, recent improvement of the mechanical behaviour of these materials at ambient and high temperatures is reported. By means of a surface oxidation treatment in air it is possible to obtain four-point bending strengths in excess of 1 GPa, and the strength retention at high temperatures is significantly improved.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.679-680
• /
• 2006

Various different types of joining between High Tc superconducting(HTS) tapes were prepared and current-voltage(I-V) characteristic curves were investigated at 77 K, liquid nitrogen temperature. Two typos of HTS tapes wore used, one is no laminated tape(Sumitomo high strength type tape) and the other stainless steel laminated tape(AMSC(American Superconductors Inc.) 3ply tapes) Sample joints were lap-jointed with indium or solder. Joint resistances between Sumitomo tapes with 4-10 mm in length were estimated from I-V curves and in the range of $4-8n{\Omega}$ at 77 K. Joint resistances of AMSC tapes were in the range of $140-170n{\Omega}$, much higher than them of Sumitomo samples. The n-values of jointed HTS tapes were 50% of them with no joint. In AMSC tapes, indium is better than solder as the jointing material.

• Journal of the Korean institute of surface engineering
• /
• v.41 no.4
• /
• pp.163-168
• /
• 2008

The dental orthodontic bracket requires good mechanical properties, such as elastic strength and frictional resistance, combined with a high resistance to corrosion. The objective of this study was to investigate the effects of TiN and ZrN coating on corrosion resistance of orthodontic brackets using various electrochemical methods. Brackets manufactured by Ormco Co. were used, respectively, for experiment. Ion plating was carried out for coatings of bracket using Ti and Zr coating materials with nitrogen gas. Ion plated surface of each specimen was observed with field emission scanning electron microscopy(FE-SEM), energy dispersive Xray spectroscopy(EDS) and electrochemical tester. The corrosion potential of the TiN and ZrN coated bracket was comparatively high. The current density of TiN and ZrN coated bracket was smaller than that of non-coated bracket in 0.9% NaCl solution. Pit nucleated at angle of bracket slot.

• Carbon letters
• /
• v.8 no.2
• /
• pp.101-107
• /
• 2007

Activated carbons were prepared by impregnation of crushed clean date pits in concentrated solutions of phosphoric acid or zinc chloride followed by carbonization in absence of air at $600^{\circ}C$. Steam-activated carbon was prepared by gasifying $600^{\circ}C$-carbonization product at $950^{\circ}C$ to a burn-off = 50%. KOH- activated carbon was prepared by impregnating date pitscarbonization product obtained at $450^{\circ}C$ in concentrated KOH solution followed by carbonization at $840^{\circ}C$. Textural properties of these carbons were determined from nitrogen adsorption at $-196^{\circ}C$ and the chemistry of the carbon surface was investigated by determination and of the surface carbon-oxygen (C-O) groups using bases of variable strength and dilute HCl. The adsorption of endosulphan at $27^{\circ}C$ on all the carbons prepared was undertaken. Adsorption of this pesticide at 32 and $37^{\circ}C$ was also undertaken for steam-activated and KOH-activated carbons. Phosphoric acid-activated carbons and steamactivated carbons are mainly microporous and have high surface concentration of C-O groups of acidic nature. Steamactivated and KOH-activated carbons exhibited surface areas > 1000 $m^2/g$ and contain micro and non-micrpores. The adsorption of endosulphan was related to the surface area of non-micropores and was retarded by the high concentration of surface C-O groups. The thermodynamic properties indicated the feasibility of the adsorption process and the possible regeneration of the carbon for further use.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.1
• /
• pp.25-29
• /
• 2012

The novel type of cable under consideration is cooled by gaseous Helium at elevated pressure. Helium is known for having poor electric breakdown strength; therefore the dielectric capabilities of this type of cable must be tested under conditions similar to the envisaged operation. In order to study the dielectric performance we have designed and built a novel high pressure cryostat rated at 2.17 MPa which has been used for testing model cables of lengths of up to 1 m. The cryostat is an open system where the gas is not re-circulated. This allows maintaining a high purity of the gas. The target temperature range is between 40 K and 70 K. This substantially increases the critical current density of the HTS compared to 77 K, which is the typical temperature of cables cooled by liquid nitrogen. The cryostat presented allows for adjusting the temperature and keeping it constant for the time necessary to run a complete dielectric characterization test. We give a detailed description of the cryostat. Measurements of partial discharge inception voltages as well as the temperature distribution along the model cables as a function of time are presented.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.3
• /
• pp.219-223
• /
• 2011

Rhenium-Iridium(Re-Ir) thin films were deposited onto the tungsten carbide(WC) molding core by sputtering system. The Re-Ir films were prepared by multi-target sputtering with iridium, rhenium and chromium as the sources. Argon and nitrogen were inlet into the chamber to be the plasma and reactive gases. The Re-Ir thin films were prepared with targets having atomic percent of 3:7 and the Re-Ir thin films were formed with 240 nm thickness. The Re-Ir thin films on tungsten carbide molding core were analyzed by scanning electron microscope(SEM) and surface roughness. Also, adhesion strength and coefficient friction of Re-Ir thin film were examined. The Re-Ir coating technique has been intensive efforts in the field of coating process because the coating technique and process have been their feature, like hardness, high elasticity, abrasion resistance and mechanical stability and also have been applied widely the industrial and biomedical areas. In this report, tungsten carbide(WC) molding core was manufactures using high performance precision machining and the efforts of Re-Ir coating on the surface roughness.

• Progress in Superconductivity and Cryogenics
• /
• v.20 no.4
• /
• pp.65-69
• /
• 2018

Due to large in-field current carrying capacity and strong mechanical strength, a REBCO wire has been regarded as a viable high temperature superconductor (HTS) option for high field MRI and > 1 GHz (>23.5 T) NMR magnets. However, a REBCO magnet is well known to have an inherent problem of field inhomogeneity, so-called 'Screening Current induced magnetic Field (SCF)'. Recently, 'field shaking' and 'current overshoot operation' techniques have been successfully demonstrated to mitigate the SCF and enhance the field homogeneity by experiments. To investigate the effectiveness of current overshooting operation technique, a numerical simulation is conducted for a test REBCO magnet composed of a stack of double pancake coils using '2D edge-element magnetic field formulation' combined with 'domain homogenization' scheme. The simulation result demonstrates that an appropriate amount of current overshoot can negate the SCF. To verify the simulation results, current overshoot experiments are conducted for the REBCO magnet in liquid nitrogen. Experimental results also demonstrate the possible application of current overshoot technique to mitigate the SCF and enhance the field homogeneity.