• 한국정밀공학회지
• /
• 제27권10호
• /
• pp.45-51
• /
• 2010

Electrical discharge drilling (ED-drilling) is a widespread machining method used to bore small holes with a high aspect ratio. This paper presents additional methods by which ED-drilling can improve machining speed, tool wear, and machined surface quality. Firstly, for high machining speed, and low tool wear, a new-type electrode that was ground on one side or both sides of the cylindrical electrodes was suggested to expel debris. The debris which is generated during the machining process can cause sludge deposition and secondary discharge problems: major reasons to decrease machining speed. This new-type electrode also reduced tool wear that was due to the decrease of unstable discharge in a machining gap by helping to expel waste water and debris from the gap. Secondly, to improve the machined surface roughness, an electrolyzation process was included after drilling. This process made the machined surface smooth by means of an electrochemical reaction between an electrode and a workpiece. In this study, the machining speed, electrode wear, and surface roughness were improved by the newtype electrode and the electrolytic process.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2005년도 춘계학술대회 논문집
• /
• pp.168-173
• /
• 2005

Composite material is combined with two or more chemical ingredient and different components. FRP has been widely used for the structure of aircraft, ships, automobiles, sporting goods and other machines because of their high specific strength, high specific stiffness and excellent fatigue strength. Recently, the development of machine tool and cutting tool greatly relies on high speed process to satisfy high precision, high efficient machining, shortened process time to maximize material removal rate (MRR) through high cutting speed and feed speed. The research molded CFRP, GFRP as stacking sequence methods of two direction (orientation angle $0^{\circ}\;and\;0^{\circ}/9^{\circ}$) hand lay-up, drilled molded plates using cemented carbide drill and examined chip shapes, surface roughness properties.

• 한국공작기계학회논문집
• /
• 제13권2호
• /
• pp.1-8
• /
• 2004

Applications of the deep hole drilling process can be found in many industries ranging from large aerospace manufacturer to small tool and die shop. Deep hole drilling process with small diameter generally requires high quality and accuracy. But problems which may arise or result from the deep hole drilling process include drill breakage, the generation of a finished part surface which does not satisfy required quality, and process instability. To guaranty the required machining quality and accuracy, it is important to understand and improve the deep hole drilling process. In this study, deep hole drilling experiments using tingle edge drill with small diameter under 2mm have been carried out for difficult to cut materials such as C42CrMo4 and C45pb and the experimental results were analyzed. Feed force and torque versus feed showed linear relationship in both materials. The feed force and torque are decreased as cutting speed is increased but the trends are not uniform in C42CrMo4.

• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3175-3184
• /
• 1994

The high strength and wear-resistant metal bonded diamond wheel was applied to the drilling process of carbon fiber reinforced plastics (CFRP), The helical-feed drilling method was use for the first time to overcome the limit of drilling depth of the conventional drilling process and to improve the dressing of the wheel. The helical-feed drilling method was found effective at high cutting speed without the limit of drilling depth.

• 한국기계가공학회지
• /
• 제4권1호
• /
• pp.18-23
• /
• 2005

This paper reports experimental results on microdrilling process for silicon parts used in semiconductor equipments. An experimental system was developed consisting of a high speed precision machine, microscope system, and project profile instrument. The experimental results indicate that the amount of chipping at the entrance and exit of micro hole decreases as the spindle speed increases up to 18,000 rpm. At higher spindle speed, however, the amount of chipping increases rapidly. The amount of chipping and infeed rate show proportional relationship up to 20 m/min of infeed rate. Beyond that infeed rate, however, sudden increase in the amount of chipping has occurred.

• 한국정밀공학회지
• /
• 제16권3호통권96호
• /
• pp.47-52
• /
• 1999

Theoretical and experimental studies on burr formation and deburring in many manufacturing processes have been actively pursued. Though micro-drilling has become more important in the production of precision parts such as PCB, air bearing, camera and nozzle, most studies on drilling burr formation have focused on the conventional drilling process. This paper describes burr formation process and the effect of cutting conditions such as spindle speed, feedrate and drilling depth per one step on burr formation in drilling A6061 with drills of diameter 1.0mm and 0.6mm. Experimental results showed that burr with cap were formed at relatively low feedrates, while petal burrs with several large burr fragments were formed at high feedrates. Burr height appeared to increase at the hight feedrates and lower spindle speeds. The effect of final cutting depth on burr height was negligible.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.923-928
• /
• 1997

An MCP (Microchannel Plate) is a secondary electron multiplier to detect and amplify electrons. An MCP has many rnicrochannels whose diameters range from 10 to 100pm and whose lengths range from 40 to 100times of the diameter. Each microchannel of the MCP amplifies electrons over IOOOtimes by the secondary electron emission. Even though MCPs have high performance for electron amplification, the application of MCPs is limited to high performance electronic equipments because of their high fabricating cost and the limit of increasing their size due to the conventional fabrication process. Therefore, in this work, microchannels of the MCP are manufactured by micro-drilling to reduce the cost of the MCP and to increase their size. Alumina green body with epoxy binder was machined for fabricating microchannels using a high speed air turbine spindle and micro-drills with diamond grinding abrasives. Then alumina MCP was fabricated through the sintering of the machined alumina green body.

• 한국기계가공학회지
• /
• 제20권6호
• /
• pp.10-16
• /
• 2021

Drilling is a crucial process that takes up a significant amount of weight during machining operations. In addition, drill tip-type tools and related operations have been developed for manufacturing industries to achieve economic efficiency. In this study, SM45C carbon steel, widely used for machine structures, was utilized as the working material after quenching and tempering. Insert-tip types of carbide tools, such as TiN and TiAlN, were used as tool materials. Drilling conditions such as the spindle revolution, feed rate, step of cut, and tool diameter were used to measure roughness, roundness, and straightness using the orthogonal array table statistical method. The surface roughness, roundness, and straightness characteristics based on the conditions were analyzed using ANOVA. The results showed that the spindle speed and feed rate were the main factors influencing carbide insert-tip drilling under the same conditions as the experimental conditions.

• 한국정밀공학회지
• /
• 제3권2호
• /
• pp.91-101
• /
• 1986

This paper deals with the effect of static and dynamic cuttig force and the behaviour of drill life in drilling process. The experiments are performed with cemented carbide drills and high speed steel drills of 10mm in diameter and in an annealed SM45C. The conclusions are as follows (1) Dynamic cutting force is varied with the dept of hole. (2) Dynamic cutting forces of torque and thrust are increase with the increase in feed and cutting speed. (3) Chipping influence the dynamic cutting force of thrust than torque, and in the case of thrust, the amplitude is 3-7 times large than ordinary cutting state. (4) Prediction of drill life can be obtained from more easily the amplitude of static cutting force than that of dynamic cutting force.

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.7-15
• /
• 2018

Drilling processes require a cutting monitoring function that can be analyzed and gives feedback about strange conditions, tool collision and tool wear in real time. In this study, we proposed a drill monitor using the torque from the main spindle in CNC machine tools and a PROFIBUS network as a PLC-based interface. This paper studied drilling torque changes depending on drill size, the repetition cutting of the drilling and the drill's wear in the same cutting conditions. The material of the drills was high speed steel (HSS) and uncoated. The drills chosen were 2.7 mm, 6.7 mm, and 10.0 mm in diameter. These drills were selected because they had basic holes for their taps.