• Tribology and Lubricants
• /
• 제15권4호
• /
• pp.335-342
• /
• 1999

Corrosion of the disk has been an ongoing concern for the manufacturers of hard disk drives. With the advent of magnetoresistive (MR) head, very low levels of corrosion and contamination become more critical since the raised defects and corrosion products on the disk surface-anything that heats the MR sensor due to the contact-can distort the output signal of the head. This phenomenon is called as thermal asperity. In this paper, the effect of corrosion as a form of Co migration on the occurrence of thermal asperity in MR drives was investigated. The corrosion test at high temperature (60$^{\circ}C$) and high relative humidity (80%) was emphasized in this study and the testing results at ambient condition were compared. The corrosion on the disks was characterized as the amount of Co ion migration using an ion chromatography (IC) and a time-of-flight secondary ion mass spectroscopy (TOF-SIMS). It is proved that corrosion on the disk surface after storage testing is closely correlated to the amount of Co ions migration from the magnetic layer to disk surfaces and higher Co migration causes more thermal asperities in the drive. In order to reduce Co migration, several methods such as burnishing process and structure of the carbon overcoat were investigated. It is found that the hydrogenated carbon overcoat shows the least Co migration among different types of overcoat layer. However, the most effective way to reduce Co migration is the application of Cr layer between the overcoat and the magnetic alloy layer.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권4호
• /
• pp.363-367
• /
• 2015

본 연구는, 증발부에 핵비등 전열 촉진면을 사용하여 수평상태에서도 작동 가능한 고성능 버블젯 루프 히트파이프(BJLHP)의 개발에 관한 것이다. 비등 촉진 전열면은 소결관과 GEWA-T 전열관을 사용하였으며, 평활관을 사용한 BJLHP와 유효열전도도를 사용하여 열성능을 비교, 검토하였다. 작동유체로는 R-141b를 사용하였으며, 충전량은 BJLHP 내부 체적의 50%, 입열량은 75W와 100W로 하였다. 그 결과 소결관을 사용한 BJLHP의 열성능이 가장 우수한 것으로 나타났으며, 소결관을 사용한 BJLHP의 유효열전도도가 평활관 BJLHP보다 300% 이상 향상되었다.

• 대한원격탐사학회지
• /
• 제32권1호
• /
• pp.25-38
• /
• 2016

With the increasing need for high temporal resolution satellite imagery for monitoring land surfaces, this study evaluated the temporal resolution of the NDVI composites from Geostationary Ocean Color Imager (GOCI) data. The GOCI is the first geostationary satellite sensor designed to provide continuous images over a $2,500{\times}2,500km^2$ area of the northeast Asian region with relatively high spatial resolution of 500 m. We used total 2,944 hourly images of the GOCI level 1B radiance data obtained during the one-year period from April 2011 to March 2012. A daily NDVI composite was produced by maximum value compositing of eight hourly images captured during day-time. Further NDVI composites were created with different compositing periods ranging from two to five days. The cloud coverage of each composite was estimated by the cloud detection method developed in study and then compared with the Moderate Resolution Imaging Spectroradiometer (MODIS) Aqua cloud product and 16-day NDVI composite. The GOCI NDVI composites showed much higher temporal resolution with less cloud coverage than the MODIS NDVI products. The average of cloud coverage for the five-day GOCI composites during the one year was only 2.5%, which is a significant improvement compared to the 8.9%~19.3% cloud coverage in the MODIS 16-day NDVI composites.

• Earthquakes and Structures
• /
• 제17권1호
• /
• pp.49-61
• /
• 2019

A novel asymmetrical resistance friction damper (ARFD) was proposed in this study to be applied on a rocking column base. The damper comprises multiple steel plates and was fastened using high-strength bolts. The sliding surfaces can be switched into one another and can cause strength to be higher in the loading direction than in the unloading direction. By combining the asymmetrical resistance with the restoring resistance that is generated due to an axial load on the column, the rocking column base can develop a self-centering behavior and achieve high connection strength. Cyclic tests on the ARFD proved that the damper performs a stable asymmetrical hysteretic loop. The desired hysteretic behavior was achieved by tuning the bolt pretension force and the diameter of the round bolt hole. In this study, full-scale, flexural tests were conducted to evaluate the performance of the column base and to verify the analytical model. The results indicated that the column base exhibits a stable self-centering behavior up to a drift angle of 4%. The decompression moment and maximum strength reached 42% and 88% of the full plastic moment of the section, respectively, under a column axial force ratio of approximately 0.2. The strengths and self-centering capacity can be obtained by determining the bolt pretension force. The analytical model results revealed good agreement with the experimental results.

• Restorative Dentistry and Endodontics
• /
• 제45권4호
• /
• pp.52.1-52.11
• /
• 2020

Objectives: Yttria-stabilized tetragonal phase zirconia has been used as a dental restorative material for over a decade. While it is still the strongest and toughest ceramic, its translucency remains as a significant drawback. To overcome this, stabilizing the translucency zirconia to a significant cubic crystalline phase by increasing the yttria content to more than 8 mol% (8YTZP). However, the biocompatibility of a high amount of yttria is still an important topic that needs to be investigated. Materials and Methods: Commercially available 8YTZP plates were used. To enhance cell adhesion, proliferation, and differentiation, the surface of the 8YTZP is sequentially polished with a SiC-coated abrasive paper and surface coating with type I collagen. Fibroblast-like cells L929 used for cell adherence and cell proliferation analysis, and mouse bone marrow-derived mesenchymal stem cells (BMSC) used for cell differentiation analysis. Results: The results revealed that all samples, regardless of the surface treatment, are hydrophilic and showed a strong affinity for water. Even the cell culture results indicate that simple surface polishing and coating can affect cellular behavior by enhancing cell adhesion and proliferation. Both L929 cells and BMSC were nicely adhered to and proliferated in all conditions. Conclusions: The results demonstrate the biocompatibility of the cubic phase zirconia with 8 mol% yttria and suggest that yttria with a higher zirconia content are not toxic to the cells, support a strong adhesion of cells on their surfaces, and promote cell proliferation and differentiation. All these confirm its potential use in tissue engineering.

• Fisheries and Aquatic Sciences
• /
• 제7권2호
• /
• pp.64-69
• /
• 2004

A bacteriological survey for 20 large grocery stores (M 1 to M20) in Korea was investigated for one year. The average detection rate of Esherichia coli was $22\%$ (166/763) for 7 kinds of ready-to-eat food through the year, where each grocery store and each type of food showed different detection rates. Eleven grocery stores showed lower detection rates, while 9 grocery stores showed a higher than average rate. Especially, M3 showed a rate that was twice as high as the average and one which was 7 times higher than M14, which had the lowest rate of $6\%$ E. coli detection. The detection rate for each type of food was: $38\%$ (41/109) for Kimbop, $31\%$ (34/109) for vegetable salad, $19\%$ (21/109) for bean-curd, $18\%$ (20/109) for the cooked materials used in making Kimbop, $17\%$ (19/109) for Hoe (sliced raw fish) and Sushi (Japanese vinegared rice delicacies), and $11\%$ (12/109) for cooked pork hock. During the summer, the E. coli detection rate averaged $43\%$ (71/166), which was twice as high as other seasons. Most (89/100) of the food contacting surfaces contained more than the critical limit $(1.3\;log_{10}\;CFU/10cm^2)$ of aerobic viable cell counts (AVC). The $log_{10}$ AVC and $log_{10}$ coliform count (CC) of 218 meat samples (beef, pork, and chicken) ranged between 4.6-7.1 CFU/g and 1.9-6.4 CFU/g, except for 41 meat samples $(19\%)$ which were found to contain no coliform. There was a definite correlation between the $log_{10}$ AVC and $log_{10}$ CC, and the values of $log_{10}$ CC made a more accurate straight than the $log_{10}$ AVC, which are variable. From these results, it is suggested that a detection rating of less than 2.1 CFU/g of $log_{10}$ CC (correspond to 5.0 CFU/g of $log_{10}$ AVC) is the critical point of freshness, and a rating of more than 6.3 CFU/g of $log_{10}$ CC (correspond to 7.0 CFU/g of $log_{10}$ AVC) can be considered an initial spoilage point.

• 한국정밀공학회지
• /
• 제29권1호
• /
• pp.19-24
• /
• 2012

We demonstrate the desert beetle back mimicking hybrid superhydrophilic/superhydrophobic patterned surface by using the combination method of colloidal lithography and gravure offset printing for nano and micro patterning, respectively. The two methods are cost-effective and industrially available techniques compared to the other nano/micro patterning methods. To verify the water collecting function of the hybrid surface, the water condensation behavior is investigated on the chilled surface in ambient temperature and high humidity. Due to the synergetic effect of drop and film wise condensation, the hybrid superhydrophobic/superhydrophilic surface shows the higher efficiency than one of single wettability surfaces. The work is underway to get the good patterns of hybrid surfaces for water collecting from the dew or fog.

• 에너지공학
• /
• 제13권1호
• /
• pp.12-19
• /
• 2004

배선용 차단기(MCCB)는 과부하 및 단로 등의 이상 상태시 전류를 차단하는 기구로, 오작동시에는 중대사고를 초래한다. MCCB를 개발하는데 있어서 고전류 및 향상된 방열성능은 소형화 및 성능향상을 필요로 하는 기기의 안전기능 및 신뢰성을 확보하는데 그 중요성이 더해 가고 있다. 또한, MCCB를 설계하는데 있어 온도상승 요인을 고려하는 것은 매우 중요하다. 온도상승의 주된 원인은 기기 내부저항, 특히 접속부와 접촉부로부터의 저항을 들 수 있는데, 전류, 시간, 접촉면의 형상, 그리고 사용전압에 의하여 영향을 받는다 본 연구에서는 MCCB 내부 온도분포를 예측하기 위하여 상용코드ICEPAK을 이용하여 수치해석을 수행하였다. 해석결과의 타당성을 검증하기 위하여 동일 모델을 사용한 실험결과와 비교하였는데, 일치된 결과를 얻을 수 있었다.

• 방사성폐기물학회지
• /
• 제7권1호
• /
• pp.33-38
• /
• 2009

신선한 흑운모 및 인위적으로 풍화시킨 흑운모에 대한 우라늄 수착 실험을 실시하였다. 실험 이후, 원심분리하여 상등액은 유도결합플라즈마분광분석(ICP-MS)으로 우라늄 농도를 분석하였고, 고체시료는 X-선 회절분석(XRD) 및 주사전자현미경(SEM) 분석을 실시하였다. 3 mm 이하의 흑운모 시료를 7개월 간 실험실에서 풍화시킨 후, 신선한 흑운모와 동일한 조건으로 pH 변화에 따른 우라늄 수착량을 구하였다. 낮은 pH(pH 3)에서는 흑운모에 대한 우라늄의 수착이 크지 않았지만, pH가 증가함에 따라 점차 우라늄 수착이 증가하는 경향을 보였다. 풍화된 흑운모의 우라늄 수착량은 신선한 흑운모에 비해 작았고 높은 pH(pH 11)에서는 그 차이가 더 심하였다. 풍화된 흑운모의 낮은 우라늄 수착특성은 광물 표면의 변화 및 주위 용존이온들의 화학적 거동에 의한 것으로 보인다. 풍화된 흑운모 시료에는 광물 표면에서 선호되는 흡착자리가 파괴되거나 용해되고 더불어 용존 이온들의 콜로이드화에 의해 우라늄-광물 표면 수착반응이 감소되는 것으로 보인다.

• Nuclear Engineering and Technology
• /
• 제48권4호
• /
• pp.932-940
• /
• 2016

Pool boiling heat transfer of water saturated at atmospheric pressure was investigated experimentally on Cu surfaces with high-temperature, thermally-conductive, microporous coatings (HTCMC). The coatings were created by sintering Cu powders on Cu surfaces in a nitrogen gas environment. A parametric study of the effects of particle size and coating thickness was conducted using three average particle sizes (APSs) of $10{\mu}m$, $25{\mu}m$, and $67{\mu}m$ and various coating thicknesses. It was found that nucleate boiling heat transfer (NBHT) and critical heat flux (CHF) were enhanced significantly for sintered microporous coatings. This is believed to have resulted from the random porous structures that appear to include reentrant type cavities. The maximum NBHT coefficient was measured to be approximately $400kW/m^2k$ with APS $67{\mu}m$ and $296{\mu}m$ coating thicknesses. This value is approximately eight times higher than that of a plain Cu surface. The maximum CHF observed was $2.1MW/m^2$ at APS $67{\mu}m$ and $428{\mu}m$ coating thicknesses, which is approximately double the CHF of a plain Cu surface. The enhancement of NBHT and CHF appeared to increase as the particle size increased in the tested range. However, two larger particle sizes ($25{\mu}m$ and $67{\mu}m$) showed a similar level of enhancement.