• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.88.1-88.1
• /
• 2015

In recent printed electronics technology, Photo-Sintering, a technique for sintering materials using a light source, has attracted attention as an alternative to time-consuming high-temperature thermal processes. The key principle of this technique is the selective heating of a strongly absorbent thin film, while preventing the heating of the transparent substrate by the light source. Many recent studies have used a flash lamp as the light source, and investigated the material-dependent effect of the width or intensity of the pulsed light. However, the flash lamp for sintering is not suitable for industry yet, because of needing too high power to sinter for a large scale. In energy-saving and large-scale sintering, LED technologies would be very useful in the near future. In this work, we investigated a sintering process for silver nanoparticles using UV-LED array. Silver nanoparticles in ink were inkjet-printed on a $1{\times}1cm$ area of a PET film and photo-sintered by 365 nm UV-LED module. A sheet resistance value as low as $72.6m{\Omega}/sq$ (2.3 - 4.5 times that of bulk silver) was obtained from the UV-LED sintering at 300 mW/cm2 for 50 min.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.219-222
• /
• 1999

Concrete is to be important quality in placement point and exact test method needed about early judgement method concrete on placement point. But early judgement method of concrete proposed various kind of method because the problems of accuracy and the time required of test exists, it is used within the limits. This study is to propose of early strength judgement by using microwave for accurate estimating early strength of concrete and to develop test machine. Through out this study we find that belows. 1) Strength development of concrete specimen according to the time heated by microwave showed the height strength development in 9 minutes regardless of slump and w/c. 2) As cooling time is long, strength of concrete specimen according to the time heated by microwave showed high strength development and this tendency is like regardless of heating time, w/c and slump. 3) As w/c is high, accelerating strength development according to w/c showed lower strength development and this tendency is like regardless of slump, heating time and cooling time. 4) As slump is big, compressive strength of specimen in standard curing showed lower value and as w/c is big, strength development showed lower

• Journal of Biosystems Engineering
• /
• 제34권1호
• /
• pp.44-49
• /
• 2009

This study was conducted to investigate the pyrolysis characteristics of switchgrass using TGA-FTIR instrument. Switchgrass is a high yielding perennial grass that has been designated as a potential energy crop, because of its high energy value. Ground switchgrass were pyrolysed at different heating rates of 10, 20, 30, and $40^{\circ}C/min$ in a TGA-FTIR instrument. The thermal decomposition characteristics of switchgrass were analyzed, and the gases volatilized during the experiment were identified. The thermal decomposition of switchgrass started at approximately $220^{\circ}C$, followed by a major loss of weight, where the main volatilization occurred, and the thermal decomposition was essentially completed by $430^{\circ}C$. The pyrolysis process was found to compose of four stages; moisture evaporation, hemicellulose decomposition, cellulose decomposition, and lignin degradation. The peak temperatures for hemicellulose decomposition ($306^{\circ}C$ to $327^{\circ}C$) and cellulose decomposition ($351^{\circ}C$ to $369^{\circ}C$) were increased with greater heating rates. FTIR analysis showed that the following gases were released during the pyrolysis of switchgrass; $CO_2$, CO, $CH_4$, $NH_3$, COS, $C_{2}H_{4}$, and some acetic acid. The most gas species were released at low temperature from 310 to $380^{\circ}C$, which was corresponding well with the observation of thermal decomposition.

• 대한기계학회논문집A
• /
• 제20권10호
• /
• pp.3126-3134
• /
• 1996

In this paper, to examine the propagation of inclined surface crack due to frictional heating, analytic model is considered as the semi-infinite elastic body subjected to the thermo-mechanical loading of an asperity moving with a high speed. Considering the moving of frictional heat source and convection on a semi-infinite surface having inclined crack, theoretical analysis was carried out to estimate the propagation characteristics of thermo-mechanical crack. Numerical results showed that stress intensity factor $K_\prod/P_0\sqrt{c}$ is increasing with increasing velocity and frictional coefficient, inclined degree, decreasing crack length and the maximum value of it is positioned at the trailing edge. So it is shown that the propagation probability of surface crack is high at the trailing edge of contact area as increasing velocity and frictional coefficient, inclined degree, as decreasing crack length.

• 한국태양에너지학회 논문집
• /
• 제27권1호
• /
• pp.83-90
• /
• 2007

Apartment balcony has been indiscreetly remodeled since the government permitted remodeling on January 2006. But remodeled balcony has a few problems such as increase of heating energy, surface condensation and cold draft. The reason of thermal problem is mainly caused by the window system in a extended balcony. The purpose of this study is to analyze heating and cooling energy and propose the efficient window types for the extended balcony area of a apartment building. 4 types of window system which have fairly high U value in Korea are investigated as follows ; double clear glass, double low-e glass, triple clear glass and triple low-e glass. Comparing double clear 91ass with double low-e glass, triple clear glass and triple low-e glass, simulation results show that 10%, 7% and 15% saving of total primary energy can be expected.

• 한국가시화정보학회지
• /
• 제22권1호
• /
• pp.6-17
• /
• 2024

This study examined the natural convection heat flow characteristics of the melting process of PCM (palm oil) inside a liquid flexitank(bag) for a cargo container. A film heating element was installed on the bottom of the container, and numerical analysis was performed under heat flux conditions of 1,000 to 4,000 W/m². As a result, the melt interface of the PCM rises to a nearly horizontal state over time. In the initial stage, conduction heat transfer dominates, but gradually waves at the cell flow and melt interfaces are formed due to natural convection heat transfer. As melting progresses, the Ra number increases parabolically, and the Nu number increases linearly and has a constant value. The Nu number rises slowly under low heat flux conditions, whereas under high heat flux conditions, the Nu number rises rapidly. As the heat flux increases, the internal temperature oscillation of the liquid phase after melting increases. However, under high heat flux conditions, excess heat exceeding the latent heat is generated, and the temperature of the molten liquid is raised, so the increase in melting rate decreases. Therefore, the appropriate heating element specification applied to a 20-ton palm oil container is 2,000 W/m².

• 분석과학
• /
• 제7권3호
• /
• pp.329-338
• /
• 1994

기체 크로마토그래피에 의한 단일 컬럼상에서 천연가스 성분의 용리거동을 알아보았다. 천연가스 성분의 용량인자인 k'값을 결정하기 위하여 불감시간 $t_0$를 동족계열에 의한 외삽법으로 구하였다. 여러 가지 온도에서 $C_1$부터 $C_5$까지 동족계열의 머무름 시간을 탄소수에 대해서 도시하면 어느 한 점에 수렴하게 되는데, 이 점을 $t_0$로 정하였다. n-부탄을 기준으로 온도에 따른 컬럼효율의 변화를 알아본 결과 온도가 증가할수록 컬럼효율은 증가하였으나, 분리시간이 짧은 시료들의 분리도는 감소하였다. 28% DC-200 정지상에서 흡착엔탈피 변화값을 구하였고, 천연가스 성분들의 머무름 메카니즘을 알아보기 위해 log $t_R$, log k' 및 log ${\alpha}$값을 van der Waals 부피(Vw), 분자간 연결지수(X) 및 소수성 계열상수(f)와의 희귀분석을 수행한 결과 log k'과 Vw 및 f가 높은 상관관계를 보여 주었다. 천연가스 성분의 물리적 성질과 물리적 파라미터와의 상관관계를 알아본 결과는 Vw는 분자량과 발열량(${\Delta}H_{comb}$), X는 끓는 점, f는 분자량, 끓는 점 및 발열량과 상관계수가 0.99 이상으로 높은 상관관계를 나타내었다. Vw와 발열량과의 회귀방정식을 이용하여 $C_6$호부터 $C_{10}$까지의 발열량을 예측한 결과 문헌값과 0.2%의 상대오차 범위내에서 일치하였다.

• 전자공학회논문지
• /
• 제53권6호
• /
• pp.155-166
• /
• 2016

전자유도 가열시설에서 정밀하고 일정한 주파수 성분에 의해 가열물체에 발열을 유도하려면 LC공진회로 설계단계에서 출력 주파수에 대한 커패시터의 정전용량(C)과 워크코일의 유도계수(L) 설정이 중요하다. 하지만 고유의 발열계수를 가진 물체의 가열위치와 범위에 직접유도를 하는 워크코일은 고정적으로 설계되는 반면 커패시터는 가변되도록 설계되어야만 전체장비의 활용도가 높아진다. 본 논문에서는 $1000V_{MAX}$ 최대전압과 $200I_{MAX}$ 전류에서 최대 700kHz의 고주파 LC공진 출력이 되도록 커패시터 내부구성 원자재 선정 및 공정설계 단계까지 단일전극 용량별 샘플을 추출하였다. 그리고 정전용량 규격변화에 따라 주파수 변화특성과 출력 파라메타 결과를 바탕으로 HF-LC공진용 전도냉각 커패시터의 최적설계를 위한 관계를 증명하는 기초 실험결과를 제시하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2003년도 학술.기술논문발표회
• /
• pp.31-34
• /
• 2003

Sandwich panel is composed of the facing sheets which support the external load, the cellular core with the low thermal conductivity and the adhesive agent to bond them. The cellular core was produced by binding lightweight cellular aggregates with cement and two types of acrylic base St/BA emulsion were added with a view to improving the workability ion due to high absorption of light weight aggregate and to develope more strength, respectively. This investigation is to comprehend the effect of the addition of two types of St/BA on thermal conductivity, calorific value and exhaustion content of noxious gas in addition re compressive and flexural strength. Flexural strength of the specimen made with St/BA-2 ranged 20kgf/cm2 to 25kgf/cm2 and was about 50% to 100% as high as that of the non-fiber specimen. Thermal conductivity was recorded from 2.0 to 3.0 kcal/mh$^{\circ}C$ and calorific value of St/BA modified specimen was much lower than that of commercial sandwich panel core of EPS and urethane. Careful caution has to be taken because generation of noxious gas such as CO, NO and SO2 tend to increase with addition of polymer cement ratio.

• 한국조리학회지
• /
• 제20권2호
• /
• pp.89-99
• /
• 2014

본 연구의 목적은 대구뼈를 이용하여 열수추출방식으로 육수를 제조하는 것이었다. 제조한 육수의 이화학적 검사(수분함량, pH, 염도, 당도, 무기질), 관능검사(묘사분석, 기호도 검사)를 통해 열수추출방식을 이용한 대구육수 제조의 표준 제조법을 알아보고자 하였다. 수분함량은 가열시간 증가 시 유의적(p<0.001)으로 낮아졌으며, 색도는 이와 반대되는 경향을 보였다. pH는 30분 가열시료인 CS1이 가장 낮았고, CS5가 가장 높았다. 염도와 당도는 육수의 가열시간이 길어질수록 유의적(p<0.001)으로 증가하였다. 대구육수의 무기질 중 Na은 137.87~154.17 mg으로 함량이 가장 높았으며, Mg와 Fe는 가열시간이 길어짐에 따라 비례적으로 증가하였다. 이상의 결과로 보아, 대구육수의 무기질 중 Na, Mg, Fe의 함량은 가열시간이 따라 영향을 받는 것을 알 수 있었으나, K, Ca은 비례적인 변화가 없었다. 대구육수의 관능검사 중 묘사분석 결과, 육수색의 강도, 투명도, 비린 냄새와 구수한 냄새, 짠맛, 감칠맛은 가열시간이 길어질수록 유의적(p<0.001)인 차이를 보이며 강하게 평가되었다. 그러나 시원한 맛은 CS4가 가장 강하게 평가되었다. 대구육수의 기호도 검사결과 중 외관, 향, 맛, 뒷맛, 전체적인 기호도에서 CS4가 가장 좋은 것으로 평가되었으며, 가열시간 증가 시 좋은 것으로 평가되었다. 이상의 결과로 보아, 대구육수의 제조 시 양파, 셀러리, 무, 바지락, 물, 대구뼈 등 모든 재료를 넣고 끓기 시작한 시점으로부터 60분을 가열하였을 때 무기질 등의 영양소 함량은 높으며, 기호도는 상승된 우수한 대구육수를 제조할 수 있는 것으로 나타났다.