• Computers and Concrete
• /
• 제14권3호
• /
• pp.299-313
• /
• 2014

Effects of polypropylene (PP) fibers, steel fibers (SF) and hybrid on the properties of highstrength fiber reinforced self-consolidating concrete (HSFR-SCC) under different volume contents are investigated in this study. Comprehensive laboratory tests were conducted in order to evaluate both fresh and hardened properties of HSFR-SCC. Test results indicated that the fiber types and fiber contents greatly influenced concrete workability but it is possible to achieve self consolidating properties while adding the fiber types in concrete mixtures. Compressive strength, dynamic modulus of elasticity, and rigidity of concrete were affected by the addition as well as volume fraction of PP fibers. However, the properties of concrete were improved by the incorporation of SF. Splitting tensile and flexural strengths of concrete became increasingly less influenced by the inclusion of PP fibers and increasingly more influenced by the addition of SF. Besides, the inclusion of PP fibers resulted in the better efficiency in the improvement of toughness than SF. Furthermore, the inclusion of fibers did not have significant effect on the durability of the concrete. Results of electrical resistivity, chloride ion penetration and ultrasonic pulse velocity tests confirmed that HSFR-SCC had enough endurance against deterioration, lower chloride ion penetrability and minimum reinforcement corrosion rate.

• 대한금속재료학회지
• /
• 제50권4호
• /
• pp.285-292
• /
• 2012

Hot ductility behavior of precipitation-hardened low-carbon iron alloys containing 0.02 wt% Ti and 0.05 wt% Nb was characterized by a hot tensile stress test. Carbon (0.05, 0.1, 0.25 wt%) and boron (0.002 wt%) contents were varied to study the effect of precipitates on the high-temperature embrittlement of the alloys in the temperature range of $600{\sim}800^{\circ}C$. Ductility loss was observed at $700^{\circ}C$ for the tested alloys. The cause of the ductility loss was mainly attributed to the carbides and ferrite films formed at the grain boundaries during deformation. Although the carbon content tended to raise the total fraction of Nb (C, N), the precipitates were formed mostly in the grain interior as the precipitation temperature was raised above the deformation temperature by the high carbon content. Hence, carbon in excess suppressed the hot ductility loss. Meanwhile, boron addition improved the hot ductility of the alloys. The improvement is likely due to the boron atoms capturing carbon atoms and thus retarding the carbide formation.

• 열처리공학회지
• /
• 제13권5호
• /
• pp.355-359
• /
• 2000

Ion beam assisted deposition system was used to deposit CNx coatings with various thickness on the substrates of high-frequency induction hardened steels. Rolling contact fatigue tests were performed using Polymet RCF-1 machine with a constant supply of lubricant. Rolling contact fatigue life was substantially different in the steels with various thickness of CNx coatings. The optimum thickness of CNx coating was found to be $8.9{\mu}m$, showing the longest fatigue life, mainly caused by higher resistance to initiation of cracks and protective overcoat remaining to the surface failure during rolling contact fatigue. Cracks were initiated in the substrates under the surface of wear track and propagated to the surface, which eventually resulted in the failure. The reduction of fatigue life observed in the specimen with elimination of CNx coating during rolling contact fatigue was explained by the substrates deformation.

• Advances in Computational Design
• /
• 제1권2호
• /
• pp.139-154
• /
• 2016

The usage of sandwich structure is extensively increasing in lightweight protective structures due to its low density and other useful properties. Sandwich panels made of metal sheets with unfilled cellular cores are found to exhibit lower deflections by comparing to an equivalent monolithic plate of same metal and similar mass per unit density. However, the process of localized impact on solid structures involving plastic deformation, high strain rates, temperature effect, material erosion, etc. does not hold effectively as that of monolithic plate. In present work, the applications of the sandwich plate with corrugated core have been extended to develop optimized lightweight armour using foam as medium of its core by explicit finite element analysis (FEA). The mechanisms of hardened steel projectile penetration of aluminum corrugated sandwich panels filled with foams have been numerically investigated by finite element analysis (FEA). A comparative study is done for the triangular corrugated sandwich plate filled with polymeric foam and metallic foam with different densities in order to achieve the optimum penetration resistance to ballistic impact. Corrugated sandwich plates filled with metallic foams are found to be superior when compared to the polymeric one. The optimized results are then compared with that of equivalent solid and unfilled cores structure to observe the effectiveness of foam-filled corrugated sandwich plate which provides an effective resistance to ballistic response. The novel structure can be the alternative to solid aluminum plate in the applications of light weight protection system.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 추계학술발표회 초록집
• /
• pp.12-12
• /
• 2000

This paper investigated the effect of the film deposition rate for $CrN_x$ microstructure and mechanical properties. For these purpose, pure Cr an stoichiometric CrN films were deposited with various target power density on Si hardened M2 tool steel. The variation of ni trogen concentration in $CrN_x$ f analyzed by AES and deposition rate was calculated by measuring of thickness using ${\alpha}-step$ profilometer. The microstructure was analyzed by X-Ray Diffract and Scanning Electron Microscopy(SEM), and mechanical properties were evalua residual stress, microhardness and adhesion tests. Deposition rate of Cr and CrN increased as an almost linear function of target power density from $0.25\mu\textrm{m}/min$ and $0.15\mu\textrm{m}/min$ to $0.43\mu\textrm{m}/min$. Residual stresses of Cr and CrN films were from tensi Ie to compressive stress with an increase of deposi tion rate a compressive stresses were increased as more augmentation of deposition r maximum hardness value of $2300kg/\textrm{mm}^2$ and the best adhesion strength correspond HF 1 were obtained for CrN film synthesized at the highest target densitY($13.2W/\textrm{mm}^2$) owing to high residual compressive stress and increasing mobility.

• 한국주조공학회지
• /
• 제25권1호
• /
• pp.23-29
• /
• 2005

Mechanical characteristics of Hi-Cr cast irons containing 16.8%Cr and 3.0%C were studied with various heat treatments. After as-cast Y-block ingots were annealed fully, the ingots were machined into cylinderical specimens with the size of 9mm in diameter and 20mm in length in order to investigate the effect of heat-treatments on mechanical characteristics of high Cr cast irons. All specimens were heat-treated by quenching- tempering, austempering and cyclic heat at the various temperatures(950, 1000, 1050 and $1100^{\circ}C$) respectively. The wear amount was measured for each heat-treated specimens against the counterpart of a hardened SKD11 steel at the following conditions; wearing velocity: 0.7 m/s, load: 100N and sliding distance: 70 km. After as-cast specimens were annealed, fine $M_{3}C$ carbides were formed, which affected the hardness and the wear resistance of Hi-Cr specimens. High hardness and good wear resistance were appeared on the specimens treated at 950 and $1000^{\circ}C$ and the austempered specimens show excellent wear resistance as well as high hardness.

• 한국터널지하공간학회 논문집
• /
• 제4권1호
• /
• pp.45-55
• /
• 2002

1980년 초 서울지하철 건설공사를 계기로 국내의 터널공사에 NATM(New Austrian Tunnelling Method)공법이 적용되고 있다. 하지만, 주지보재의 하나인 숏크리트 기술은 NATM공법이 국내에 들어온 초기의 기술력을 아직 답습하고 있는 상태로 다량의 리바운드가 발생하고, 노즐맨의 경험이나 기량등에 의존하는 경우가 많아 비용절감 및 시공능률 향상을 위한 개선이 절실히 요구되고 있는 실정이다. 본 논문에서는 숏크리트 품질확보에 중요한 위치를 차지하고 있는 급결제(Accelerator)를 주변수로 강섬유보강 숏크리트(SFRS)에 대한 모형시험을 실시하여 고품질 숏크리트에의 적용 가능성을 검토하였다. 모형시험(압축강도, 휨강도, 휨인성)결과, Alkali-free 액상급결제를 사용한 숏크리트를 통해 고강도 발현을 위한 고가의 혼화재를 사용하지 않고서도 고품질의 고강도 숏크리트 개발 가능성을 확인할 수 있었으며, Single-Shell Lining 터널 등 Permanent Shotcrete Lining이라는 새로운 개념의 터널 지보시스템 구축을 위한 요소기술로 그 적용이 확대될 것으로 판단된다.

• 대한기계학회논문집A
• /
• 제40권12호
• /
• pp.1027-1035
• /
• 2016

내식성과 기계적 성능이 우수한 316L 스테인리스 강의 저주기 변형률제어 피로시험에서 3가지 변형률진폭과 3가지 변형률비의 조건이 피로수명에 미치는 효과를 분석하였다. 낮은 변형률범위에서 곡선이 거의 중첩되는 Masing 거동이 나타나고, 높은 변형률범위에서 비선형거동 응력범위가 서로 크게 벗어나는 non-Masing 거동과 함께 평균응력의 감소가 나타났다. 소성 변형률에너지를 이용하여 저주기 피로수명을 예측하고 non-Masing 거동을 고려한 수명예측 방법의 정확성 여부를 검토하였다. 각각의 변형률진폭과 변형률비의 조건에서 초기 수 사이클 동안 반복경화 현상 후 장시간동안 점진적으로 낮아져 연화하다가 파괴 되었다. 저사이클 피로수명을 정확히 예측하기 위해서는 변형률진폭에 따라 Masing 및 non-Masing 거동을 구분하고, 이를 반영한 수명예측식을 적용해야 함을 알았다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.441-444
• /
• 2008

본 연구에서의 초고성능 콘크리트(Ultra High Performance Concrete, UHPC)는 모래, 시멘트, 실리카퓸, 석영미분말, 강섬유 및 고성능감수제 등으로 구성되며, 평균입경 약 0.5mm이하의 아주 작은 입자들로 구성된다. 일반적으로 석영미분말는 일정크기 이상의 공극을 메움으로써 물리적 성능개선의 효과가 있으며 또한 높은 $SiO_2$함량을 가지므로 고온 또는 고압의 양생조건에서 시멘트 수화물과의 화학반응을 통해서도 성능 향상효과가 있는 것으로 알려져 있다. 본 연구에서는 상압, $90^{\circ}C$ 증기양생 조건에서 석영미분말의 입자크기가 초고성능 콘크리트의 역학적 특성에 어떠한 영향을 미치는지에 대해 알아보고자 하였으며, 평가항목으로는 굳지 않은 상태에서의 유동성과 굳은 상태에서의 압축강도, 극한변형률, 탄성계수 및 휨강도를 평가하였다. 석영미분말의 입경크기의 영향은 약 $2{\mu}m$에서 $26{\mu}m$까지의 범위에서 고려하였으며, 입경 크기가 작을수록 유동성 및 강도특성이 모두 향상되는 것으로 나타났다.

• Advances in concrete construction
• /
• 제8권1호
• /
• pp.21-31
• /
• 2019

The rich recipe of ultra high performance concrete (UHPC) offers the higher mechanical, durability and dense microstructure property. The variable like cement/sand ratio, amount of supplementary cementitious material, water/binder ratio, amount of fiber etc. alters the UHPC hardened properties to any extent. Therefore, to understand the effects of these variables on the performance of UHPC, inevitably a stage-wise development is required. In the present experimental study, the effect of sand/cement ratio, the addition of finer material (fly ash and quartz powder) and, hybrid fiber on the fresh, compressive and microstructural property of UHPC is evaluated. The experiment is conducted in three phases; the first phase evaluates the flow value and strength attainment of ingredients, the second phase evaluates the efficiency of finer materials (fly ash and quartz powder) to develop the UHPC and the third phase evaluate the effect of hybrid fiber on the flow value and strength of ultra high performance hybrid fiber reinforced concrete (UHP-HFRC). It has been seen that the addition of fly ash improves the flow value and compressive strength of UHPC as compared to quartz powder. Further, the usage of hybrid fiber in fly ash contained matrix decreases the flow value and improves the strength of the UHP-HFRC matrix. The dense interface between matrix and fiber and, a higher amount of calcium silicate hydrate (CSH) in fly ash contained UHP-HFRC is revealed by SEM and XRD respectively. The dense interface (bond between the fiber and the UHPC matrix) and the higher CSH formation are the reason for the improvement in the compressive strength of fly ash based UHP-HFRC. The differential thermal analysis (DTA/TGA) shows the similar type of mass loss pattern, however, the amount of mass loss differs in fly ash and quartz powder contained UHP-HFRC.