• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.430-430
• /
• 2007

In this study, the nematic liquid crystal (NLC) alignment effects treated on the ZnO thin film layers using ion beam irradiation were successfully studied for the first time. The ZnO thin films were deposited on indium-tin-oxide (ITO) coated glass substrates by rf-sputter and The ZnO thin films were deposited at the three kinds of rf power. The used DuoPIGatron type ion beam system, which can be advantageous in a large area with high density plasma generation. The ion beam parameters were as follows: energy of 1800 eV, exposure time of 1 min and ion beam current of $4\;mA/cm^2$ at exposure angles of $15^{\circ}$, $30^{\circ}$, $45^{\circ}$, and $60^{\circ}$. The homogeneous and homeotropic LC aligning capabilities treated on the ZnO thin film surface with ion beam exposure of $45^{\circ}$ for 1 min can be achieved. The low pretilt angle for a NLC treated on the ZnO thin film surface with ion beam irradiation for all incident angles was measured. The good LC alignment treated on the ZnO thin film with ion beam exposure at rf power of 150 W can be measure. For identifying surfaces topography of the ZnO thin films, atomic force microscopy (AFM) was introduced. After ion beam irradiation, test samples were fabricated in an anti-parallel configuration with a cell gap of $60{\mu}m$.

• Nuclear Engineering and Technology
• /
• 제37권5호
• /
• pp.447-456
• /
• 2005

Laser driven accelerators promise to provide an alternative to conventional accelerator technology. They rely on the excitation of large amplitude density waves in a plasma by the photon pressure of an intense laser. The density oscillations in which electrons and ions are separated, result in extremely large longitudinal electric fields that can be several orders of magnitude larger than those that are used in today's radio-frequency accelerators. Whereas this principle had been demonstrated experimentally for nearly two decades, it was not until 2004 that the production of high quality electron beams around 100 MeV was demonstrated. Analysis, aided by particle-in-cell simulations, as well as experiments with various plasma lengths and densities, indicate that tailoring the length of the accelerator, together with loading of the accelerating structure with beam, are the keys to production of mono-energetic electron beams. Increasing the energy towards a GeV and beyond will require reducing the plasma density and design criteria are discussed for an optimized accelerator module. The current progress and future directions are summarized through comparison with conventional accelerators, highlighting the unique short and long term prospects for intense radiation sources and high energy accelerators based on laser-drivenplasma accelerators.

• Structural Engineering and Mechanics
• /
• 제42권4호
• /
• pp.551-570
• /
• 2012

An experimental program was carried out to investigate the influence of fibre reinforcement on the mechanical behaviour of high strength reinforced concrete beams. Eighteen beams, loaded in four-point bending tests, were examined by applying monotonically increasing controlled displacements and recording the response in terms of load-deflection curves up to failure. The major test variables were the volume fraction of steel fibres and the transverse steel amount for two different values of shear span. The contribution of the stirrups to the shear strength was derived from the deformations of their vertical legs, measured by means of strain gauges. The structural response of the tested beams was analyzed to evaluate strength, stiffness, energy absorption capacity and failure mode. The experimental results and observed behaviour are in good agreement with those obtained by other authors, confirming that an adequate amount of steel fibres in the concrete can be an alternative solution for minimizing the density of transverse reinforcement. However, the paper shows that the use of different theoretical or semi-empirical models, available in literature, leads to different predictions of the ultimate load in the case of dominant shear failure mode.

• 한국의학물리학회지:의학물리
• /
• 제32권4호
• /
• pp.165-171
• /
• 2021

Purpose: This study aimed to evaluate the effect of collimator width on effective atomic number (EAN), relative electron density (RED), and stopping power ratio (SPR) measured by dual-layer dual-energy computed tomography (DL-DECT). Methods: CIRS electron density calibration phantoms with two different arrangements of material plugs were scanned by DL-DECT with two different collimator widths. The first phantom included two dense bone plugs, while the second excluded dense bone plugs. The collimator widths selected were 64 mm×0.625 mm for wider collimators and 16 mm×0.625 mm for narrow collimators. The scanning parameters were 120 kVp, 0.33 second gantry rotation, 3 mm slice thickness, B reconstruction filter, and spectral level 4. An image analysis portal system provided by a computed tomography (CT) manufacturer was used to derive the EAN and RED of the phantoms from the combination of low energy and high energy CT images. The EAN and RED were compared between the images scanned using the two different collimation widths. Results: The CT images with the wider collimation width generated more severe artifacts, particularly with high-density material (i.e., dense bone). RED and EAN for tissues (excluding lung and bones) with the wider collimation width showed significant relative differences compared to the theoretical value (4.5% for RED and 20.6% for EAN), while those with the narrow collimation width were closer to the theoretical value of each material (2.2% for EAN and 2.3% for RED). Scanning with narrow collimation width increased the accuracy of SPR estimation even with high-density bone plugs in the phantom. Conclusions: The effect of CT collimation width on EAN, RED, and SPR measured by DL-DECT was evaluated. In order to improve the accuracy of the measured EAN, RED, and SPR by DL-DECT, CT scanning should be performed using narrow collimation widths.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 추계학술대회 논문집
• /
• pp.167-170
• /
• 1995

LiCoO$_2$is a electrode material of Li ion Cell which is expected as the cell with a very high electric charge density. The recent study is mainly to focused on a high power secondary cell. If very thin Li ion Cell can be made in the scale of IC substrate it can be a electric souse in IC chip , micro machine or very thin electrical display etc. LiCoO$_2$thin film can be made by CVD, Laser ablation, E-Beam, ton Beam process, sputtering etc. But to make the material with a high quality for a cell is difficult as the electrode in cell have the fitable ratio in components and a lattice structure of bulk etc. In this study, LiCoO$_2$is made by R.F magnetron sputtering with the variance of substrate temperature and oxygen partial pressure etc. In the substrate temperature of 600$^{\circ}C$ and the oxygen rate of 10%, we can acquire the good thin film LiCoO$_2$compared wish a bulk material.

• Journal of Welding and Joining
• /
• 제15권3호
• /
• pp.88-98
• /
• 1997

Welding defects, such as porosity and spike, have sometimes occurred in deep penetration electron beam welds. These defects are known to be one of the serious problem in electron beam welds. So, effects of active parameters ($a_b$) on bead shape and occurrence of defects in electron beam welds of heavy section 9%Ni steel plates were investigated. Partial penetration welding in flat position, and deep penetration welding of 10 ~ 28mm depth were investigated in this study. It is desirable to select low accelerating voltage and above the surface focus position $a_b$$\geq$1.2 at which a wine-cup shaped bead is obtained to avoid the welding defects such as spike and root porosity. When the accelerating voltage of electron beam was low (90kV), active parameter ($a_b$) did not influence on the bead width, penetration depth and weld defects significantly. However, in case of high voltage ($\geq$120kV), active parameter ($a_b$) was sensitively associated with penetraton depth and weld defects, i.e. when the active parameter (($a_b$) was in the range of 0.6 to 1.0, the depth of penetration was always over the target (23mm), while the depth of penetration was dramatically decreased with further increase of active parameter ($a_b$). The weld defects were decreased with the increase of active parameter $a_b$ resulting in the decrease of energy density of the focused beam in the root part of fusion zone.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2010년도 임시총회 및 하계학술연구발표회
• /
• pp.70-71
• /
• 2010

In this study, We fabricated FePt-based perpendicular patterned media using a selective combination of E-beam lithography and either Ar plasma etching (deposition-first process) or FePt lift-off (deposition-last process). We employed the deposition-last process to avoid chemical and structural disordering by impinging Ar ions (deposition-first process). For a patterned medium with 100 nm patterns made by this process, the out-of-plane coercivity was measured to be 5 fold larger than its in-plane value. The deposition-last process may be a promising way to achieve ultra-high density patterned media.

• 한국진공학회지
• /
• 제15권6호
• /
• pp.637-641
• /
• 2006

본 논문에서는 100 nm 게이트 길이를 갖는 InGaAs/InAlAs/GaAs MHEMT(metamorphic high electron mobility transistors)m의 DC와 RF 특성을 분석 하였다. 이중 노광 방법으로 ZEP520/P(MMA-MAA)/PMMA 3층 구조의 레지스터와 게이트 길이 100 nm인 게이트를 제작하였다. 게이트의 단위 폭이 $70\;{\mu}m$인 2개의 게이트와 길이가 100 nm로 제작된 MHEMT를 DC 및 RF특성을 조사하였다. 최대 드레인 전류 밀도는 465 mA/mm, 상호전달 컨덕턴스는 844 mS/mm이, RF 측정으로부터 전류 이득 차단 주파수는 192 GHz와 최대 진동주파수 310 GHz인 특성을 보였다.

• 한국진공학회지
• /
• 제16권2호
• /
• pp.79-90
• /
• 2007

저에너지 초고속 표면 처기 이온원, 4개의 마그네트론 스퍼터 캐소드가 부착된 300 mm 폭 다목적 연성 기판 제작을 위한 부피 800 L 용량의 진공 웹코터 원형 (prototype) 장비를 설계 제작하였고, 무접착제 2층 연성 동박 적층 필림을 제작하여 성능을 평가하였다. 2 개의 터보 펌프 및 폴리콜드를 장착한 비코팅 부분인 상실부와 각각 1개씩의 터보 펌프를 사용한 표면 처리 및 코팅 부분인 하실부의 진공 배기 특성을 측정하였다. 패러데이 컵을 사용하여 대면적 이온원의 이온 전류 밀도 및 균일도를 측정하고, 스퍼터 캐소드의 자기장 분포 및 타겟 사용 효율을 조사하였다. 진공 웹코터의 성능 및 각 구성 요소의 특성 조사를 위하여 연성 기판으로는 폴리이미드 (Kapton-E) $38{\mu}m$을 사용하여 여러 가지 가스 이온에 대한표면 처리 조건에 따른 증류수의 접촉각 변화와 화학 성분의 변화를 x-선 분광학을 사용하여 조사하였다. 고밀도 2층 연성 동박 적층 필림 기판을 스퍼터-전기 도금법으로 제작하기 위하여 스퍼터 타겟으로는 Ni-Cr 및 Cu 금속을 사용하여, 각각의 증착율을 직류 전력의 변화 및 롤의 속도에 따라 조사하였고, 전기 도금으로 $9{mu}m$ 까지 동박 적층 필림을 제작한 후 접착력 및 내열성, 내화학성을 측정하여 소형 진공 웹 코터의 특성을 조사하였다.

• 한국레이저가공학회지
• /
• 제11권2호
• /
• pp.15-19
• /
• 2008

Electron beam (EB) weldability of pure grade Nb sheet was studied. One of Nb sheets was as-annealed and the other was cold rolled. Microstructures, Vickers hardness, and transverse weld tensile test were carried out for the base metal, the heat affected zone (HAZ) and weld metal. In the case of the EB welds made using the annealed Nb sheeet, fine equiaxed grains and coarse grains were dominant at the base metal and the HAZ, respectively, and columnar grains were observed at the weld metal. For the EB welds made using the cold rolled Nb sheet, elongated grains in the rolling direction at the base metal, and the microstructures of the weld metal and the HAZ are similar to those of the EB welds made using the annealed Nb sheet, respectively. For both annealed and cold rolled Nb sheet, the width of the HAZs are unusually wide in spite of using high density heat source, i.e. electron beam, and the grain sizes of both HAZs are similar. When tensile test was carried out using the transverse weld specimens, the failure occurred at the HAZ for both EB welds made using Nb sheets annealed and cold rolled, respectively and the tensile strengths of both specimens were 161MPa. Vickers hardness of EB welds made using annealed Nb was 56-57 Hv at both base metal and weld metal, 52-53 Hv at the HAZ. On the other hand, Vickers hardness of EB welds made using cold rolled Nb was 97-99 Hv at the base metal, but the hardness values of weld metal were similar to those obtained at the weld metal of annealed Nb.