• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.11
• /
• pp.841-848
• /
• 2008

DME(Di-methyl Ether) has been expected to be one of the promising alternative fuels for compression ignition engines due to its low emission characteristics for particulate matter. However, its physical properties such as density, bulk modulus and viscosity are not comparable to those of conventional diesel fuel. Especially, problems caused by low lubricity and high compressibility need to be understood more thoroughly, when a DME fuel is used for compression ignition engine, especially with mechanical fuel supply system. In this study, measurement and calculation of DME's bulk modulus were carried out over the range of temperatures from $-3^{\circ}C$ to $53^{\circ}C$, and pressures from 50 bar to 250 bar using an experimental apparatus built in this work. The results show that DME is prone to be compressed more easily compared to diesel fuel. A comparison of bulk modulus with butane and propane were also made in this work.

• Geomechanics and Engineering
• /
• v.22 no.4
• /
• pp.329-337
• /
• 2020

Polyacrylamide (PAM) possesses high water absorption capacity and a unique pH-dependent behavior that confer large potential to enhance the engineering performance of clays. In this study, calcium bentonite was treated with a nonionic PAM. Flexible-wall permeability test and the consolidation test were performed at different pH values to evaluate the effects of PAM treatment on the hydraulic and consolidation properties. Test results demonstrate that index properties are affected by the adsorbed PAM on clay surface: a decrease in specific gravity, a decrease in net zeta potential, and an increase in liquid limit are observed due to the PAM treatment. At a given pH, the compressibility of the treated clay is greater than that of the untreated clay. However, the compression indices of untreated and treated clays can be expressed as a single function of the initial void ratio, regardless of pH. Hydraulic conductivity is reduced by PAM treatment about 5 times at both neutral and alkaline pH conditions under similar void ratios, because of the reduction in size of the water flow channel by PAM expansion. However, at acidic pH, the hydraulic conductivity of the treated clay is slightly higher than the untreated clay. This reflects that the treated bentonite with PAM can be beneficially used in barrier system for highly alkaline residues.

• Journal of Korean Society of Disaster and Security
• /
• v.10 no.1
• /
• pp.55-60
• /
• 2017

The dyeing sludge can be weakened by inflow of rainfall or absorption of moisture after it is buried in a waste landfill. This study tested the dyeing sludge and earth/sand mixture to check the problem when the dehydrated dyeing sludge is buried in a waste landfill. When the dyeing sludge was left idle with high water content inside a landfill with poor draining for a long period, the water permeability decreased to around 3/100 level and the compressibility increased by 1.4 times compared to the dyeing sludge at a dyeing factory. The study result indicated that it was important to reduce the water content inside the landfill for stability. Also, the facilities to secure the drainage path and eliminate leachate were needed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.491-498
• /
• 2002

Dredged and reclaimed soft clays form slurry state which is very high water content and very low shear strength, experience large self-weight consolidation, nonlinear compressibility and permeability phenomenon would take place. In this case, a material functions which represent variety effective stress-void ratio-permeability relation (especially very low effective stress), are should be determined to predict nonlinear finite strain consolidation phenomenon forehand In this study, large slurry consolidometer with a 380mm diameter and a 1400mm height which is able to consolidation and permeability test, was developed to determine material function of very soft clay with a 500% initial water content clay, self-weight consolidation and low stress level consolidation (1Kpa, 3Kpa, 6Kpa, 12Kpa) was conducted and after each consolidation step permeability test also conducted. after final consolidation step, a constant rate of strain consolidation was conducted with undisturbed sample obtained from the large consolidometer. On the above result, material function was determined and laboratory test was modelled to evaluate its validity, numerical analysis on th field was compared to other method.

• Structural Engineering and Mechanics
• /
• v.76 no.5
• /
• pp.653-661
• /
• 2020

The paper presents a study regarding rubber compressibility behavior. The objective is to analyze the effect of compression degree of rubber on its mechanical properties and propose a new methodology based on reverse engineering to predict compressibility degree based on uniaxial stretching test and Finite Element Analysis (FEA). In general, rubbers are considered to be almost incompressible and Poisson's ratio is close to 0.5. Since this property is intimately related to the rubber packing density, little changes in Poisson's ratio can lead to significant changes regarding mechanical behavior. The deviatory hyperelastic constants were obtained through experimental data fitting by least squares method for the most relevant constitutive models implemented in commercial software Abaqus, such as: Neo-Hooke, Mooney-Rivlin, Ogden, Yeoh and Arruda-Boyce, whereas the hydrostatic part was determined through an optimization algorithm implemented in the Abaqus environment by Python scripting. The simulation results presented great influence of the Poisson's ratio in the rubber specimen mechanical behavior mainly for high strain levels. A conventional pure volumetric compression test was also carried out in order to compare the results obtained by the proposed methodology.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.1
• /
• pp.183-194
• /
• 2004

It's essential process to study non-linear material function related to characteristics of compressibility and permeability when we predict the consolidation behavior of soft clay ground. In this study, laboratory tests were conducted to find out the material function using marine clay. Standard oedometer test and Rowe cell test were performed with conditions, which were classified into vertical drainage only, radial drainage only and vertical-radial drainage case. Modified oedometer test equipment was developed to find out the material function and special extrusion device was originated to minimize the sample disturbance effect. Reliability of the results in modified oedometer test could be confirmed by comparing with the Rowe cell's one. Effective stress - void ratio - permeability relations were analyzed using all testing results. As a result, void ratio with effective stress level could be expressed by the power function and permeability with void ratio could be expressed by exponential function. In soft clay with high initial water content and low shear strength, non-linear characteristics related to compressibility and permeability varied with wide range by the effective stress levels. It's important to note that non-linearity of the material function should be considered at prediction of the consolidation behavior.

• Korean Journal of Digital Imaging in Medicine
• /
• v.6 no.1
• /
• pp.31-40
• /
• 2003

Purpose : In a PACS(Picture Archiving Communications System) environment, which is a very important component in a digital medical environment, the compression of digital medical images is a necessary and effective feature. In a current system where JPEG is applied to the compression of medical images, this study is to examine effectiveness and suitability when the JPEG2000, a more advanced compression algorithm for still images, is applied to the compression of medical images. In this thesis, we attempt to address the compressibility for effective clinical usage when compressing medical images, applying the objectivization of clinical evaluation as a function of compressibility. In the experiment al method, the compression was applied at a fixed rate using JPEG2000, and the n the result was compared with compressed images by JPEG. Method : For the performance evaluation, we choose SNR(Signal to Noise Ratio) measurement of an objective evaluation of definition and analyze a subjective evaluation by the ROC(Receiver Operating Characteristic) method. The results of the experiment showed that in the case of JPEG2000 there is hardly any distortion of images, even at high compression ratio(100:1), while regarding noise, the SNR remains around about 40dB, which is also relatively high. Before reading by reference to evaluative materials concerning objective compressed images, it is impossible to apply high compression to images : however, after reading, this can be applied to images that have already existed for some time.

• Journal of the Korean Society of Safety
• /
• v.25 no.5
• /
• pp.7-14
• /
• 2010

Ultra high pressure system, which can be generally increased over 1,000bar, needs to have sealing mechanism to protect leakage and selection of the materials used in the intensifier. Components such as pressure vessel, hydraulic hose assembly, accumulator, hydraulic cylinder, hydraulic valve, pipe, etc., are tested under the impulse-pressure conditions. Components need to be tested under 1.5 to 3 times of rated pressure to check the tolerance even though rated pressure range of these components are not ultra high pressure. So, the ultra high pressure system needs to be equiped to test components. In this study, safety assessments of ultra high pressure system which are using failure analysis of components, changing the types of the control system, and finite element analysis with static condition, are investigated.

• Journal of Mechanical Science and Technology
• /
• v.14 no.1
• /
• pp.103-112
• /
• 2000

Numerical simulations of unsteady opposed-flow flames are performed using an adaptive time integration method designed for differential-algebraic systems. The compressibility effect is considered in deriving the system of equations, such that the numerical difficulties associated with a high-index system are alleviated. The numerical method is implemented for systems with detailed chemical mechanisms and transport properties by utilizing the Chemkin software. Two test simulations are performeds hydrogen/air diffusion flames with an oscillatory strain rate and transient ignition of methane against heated air. Both results show that the rapid transient behavior is successfully captured by the numerical method.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1993.12a
• /
• pp.85-91
• /
• 1993

Air-Lubricated tilting pad journal bearing that has high stability is analyzed by using the direct method, and this bearing is usually used to need high precision. The pressure that supports the shaft is occured by the differences between the shaft and pads radii of curvatures. So the characteristics of load capacity for their variable values is important. In this paper the load capacity is compared with some of the eccentricity ratio values. The large load oapacity comes form large eccentricity ratio, high bearing number and high preload. But if the preload becomes too high, the shaft comes into contact with the pads. Stiffness and damping coefficients are compared with some of the preload, too. The coefficients decreased along compressibility number with constant load.