• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.7-10
• /
• 2003

The amount of coal ash has been increasing and development of effective use is urgently needed. Various by-products and waste are expected to be used as resources from the point of reduction in environmental load. This is an experimental study to compare the properties of high volume coal ash concrete using the reclaimed coal ash. For this purpose, the mix proportion of concrete according to the content ratio of below 5mm reclaimed coal ash (0.65, 0.70, 0.75 and 0.80). And then air content, slump, compressive strength test were performed. According to test results, it was found that the compressive strength of reclaimed coal ash concrete was similar to the content ratio of below 5mm reclaimed coal ash. And the slump of reclaimed coal ash concrete decreased as the content ratio of below 5mm.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.3
• /
• pp.73-78
• /
• 2009

Coal ash is a by-product of the combustion of pulverized coal, and much of this is dumped in landfills. The disposal of coal ash is one of the major issues for environmental problems. In this paper, the effects of the kinds and replacement ratio of coal ash on the durabilities of concrete mixtures are investigated. Fine aggregate was replaced with coal ash(fly ash and bottom ash) in five different ratios, of 0%, 10%, 20%, 35%, and 50% by volume. Test results indicated that the compressive strength increased with the increase in fly ash percentage. The loss of compressive strength of bottom ash concrete mixes after immersion in sulphuric acid solution was less than in the control mix(BA0). In addition, the carbonation depth of fly ash concrete mixes was lower than the control mix(FA0).

• Advances in concrete construction
• /
• v.6 no.4
• /
• pp.407-422
• /
• 2018

The study evaluates properties of brick having coal ash and explores the possibility of utilization of coal bottom ash and coal fly ash as an alternative raw material in the production of coal ash bricks. Lower cement content was used in the investigations to attain appropriate strength and prohibit high carbon content that is cause of environmental pollution. The samples use up to 7% of cement whereas sand was replaced with bottom ash. Bricks were tested for compressive strength, modulus of rupture, ultrasonic pulse velocity (UPV), water absorption and durability. The results showed mix proportions of bottom ash, fly ash and cement as 1:1:0.15 i.e., M-15 achieved optimum values. The coal ash bricks were well bonded with mortar and could be feasible alternative to conventional bricks thus can contribute towards sustainable development.

• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.443-450
• /
• 2008

Efficient use of low rank coals (LRC) have been investigated as a method to cope with recent high oil price. Among the coals used in industry, lignite and sub-bituminous coals are belong to the LRC, and have abundant deposit and are distributed worldwide, but high moisture contents and self ignition properties inhibits their utilization. In this paper, chemical coal cleaning to produce ash-free coal from LRC has been investigated. Two technologies, that is, UCC(Ultra Clean Coal) process removing ash from coal and Hyper Coal process extracting combustibles from coal were compared with. UCC process has merits of simple and reliable when it compared with Hyper Coal process, but the remaining ash contents werehigher than Hyper Coal. Hyper Coal has ash contents under the 200ppm when raw coal is treated with appropriate solvent and ion exchange materials to remove alkali materials in extracted solution. The ash-free coal which is similar grade with oil can be used as alternate oil in the industry, and also used as a high grade fuel for IGCC, IGFC and other advanced combustion technology.

• Architectural research
• /
• v.4 no.1
• /
• pp.39-44
• /
• 2002

Recently, the coal-ash production has been increased by increase of consumption of electric power. So it is important to secure a reclaimed land from pollution and develop practical application of coal ash. This is an experimental study to compare and analyze the properties of concrete using high volume of coal ash (including fly ash and bottom ash) as a part of fine aggregate. For this purpose, the mix proportions of concrete according to replacement ratio of coal ash (10, 20, 35, 50%) were selected. And then air content, slump, setting time, bleeding content, chloride content, compressive strength and carbonation test were performed. According to test results, it was found that the bleeding content of concrete using the coal ash decreased according to increase of replacement ratio. And the chloride content of concrete using the bottom ash as a part of fine aggregate increased as the replacement ratio of bottom ash increased, but it is satisfied with the total chloride content of concrete recommended by KCI - $0.3kg/m^3$ below. Also, the compressive strength of concrete using the bottom ash was similar to that of plain concrete(BA 0) after 28days of curing and the carbonation depth of concrete increased as the replacement ratio increased. However, the carbonation depth of concrete using the fly ash decreased as the replacement ratio of fly ash increased.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.95-98
• /
• 1998

Fly ash is glassy dust collected from coal fired power plant. Recently, much research for fly ash conducted in Korea and fly ash is a valuable material especially when it used in high strength, high flowable, high durability concrete. But it varies with coal source, coal grinding and boiler conditions. Therefore, it is important that quality control of fly ash itself to get high quality concrete. In this study, over 20 samples of Poryong and Samchonpo fly ashs are tested and analyzed. The physical, chemical properties of fly ash and their relationships are investigated and it can be applied to quality control of concrete.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.4
• /
• pp.405-413
• /
• 2013

The char oxidation characteristics of high ash coal were experimentally investigated at several temperatures (from 900 to $1300^{\circ}C$) for 4 types of coals (Gunvor, Glencore, Noble, and ECM) under atmospheric pressure in a drop tube furnace (DTF). The char reaction rate was calculated from the exhaust gas concentrations (CO and $CO_2$) using FT-IR, and the particle temperature was measured using the two-color method. In addition, the activation energy and pre-exponential factor for high ash coal char were calculated based on the Arrhenius equation. The results show that as the ash content increases, the particle temperature and area reactivity decreases. This is because in high ash coal, the large heat capacity of the ash, ash vaporization, and relatively low fixed carbon content of ash suppress combustibility during char oxidation. As a result, the higher ash content of coal leads to high activation energy.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.3
• /
• pp.211-218
• /
• 2022

Coal ash is being considered as a source of silica and alumina for cement clinker. The purpose of this study was to investigate the effect on cement clinker sintering by confirming the high-temperature microstructural change according to the firing temperature in the cement clinker sintering process of coal ash. In the coal ash used as a raw material for cement clinker, the shape change of the particle surface was confirmed from the sintering tem perature of 950 ℃. The shape of the coal ash disappeared from the sintering temperature higher than 1250 ℃. It was confirmed that the Al and Fe components of the coal ash were converted to the cement interstitial phase at a temperature higher than 1350 ℃. In addition, the clinker using a large amount of coal ash as a raw material showed a low content of Lime and a high content of Belite in the sintering tem perature range of 1150~1200 ℃. From this, it was confirmed that the formation of calcium silicate mineral proceeds more easily at the initial sintering temperature by the application of coal ash.

• Journal of Magnetics
• /
• v.18 no.3
• /
• pp.365-369
• /
• 2013

Coal ash is known to contain a noticeable amount of valuable elements, including transition metals and lanthanides. Therefore it is quite actual problem to extract them for metallurgy and other applications. This paper presents the results of high gradient magnetic and mechanical separation, microscopy, element analyses and optical spectroscopy of brown coal ash taken from the combustion camera and chimney-stalk of Angren thermal power station. The separated magnetic fraction was 3.4 wt.%, where the content of Fe in ferrospheres increased to 58 wt.%. The highest contents of Fe and rare earth elements were found in the fine fractions of $50-100{\mu}m$. Optical absorption spectroscopy of water solutions of the magnetic fractions revealed $Fe^{2+}$ and $Fe^{3+}$ ions in the ratio of ~1:1. The separated coal ash could be used for cleaning of technological liquid waste by means of the high gradient magnetic field.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.5
• /
• pp.204-210
• /
• 2004

Though the recycling rate of coal fly ash generated from domestic thermoelectric power plants is gradually increased, at present, the most amount of coal bottom ash is disposed by a landfill instead of recycling. Therefore, to reuse a coal bottom ash as high-value materials the synthesis of zeolite made from a coal bottom ash was investigated in this study. NaPl, hydroxy-sodalite and tobermorite were produced through the alkaline hydrothermal reaction of pulvelized bottom ash at various temperatures; 80, 120, $150^{\circ}C$, and the concentration of NaOH at the range from 1 to 5 M. Especially, NaPl with excellent cation exchange capability had a high crystallinity at ${\leq}2$ M NaOH and ${\leq}120^{\circ}C$.