• Journal of Biosystems Engineering
• /
• 제33권2호
• /
• pp.94-100
• /
• 2008

Present chemical application method using a power sprayer has been labor intensive, costly and ineffective. Therefore, a small agricultural unmanned helicopter was suggested to replace the conventional spray system. In this study, conceptual design for developing the helicopter and a consequential prototype were reported. The overall conceptual design was initiated by deciding the type of agricultural helicopter, as the single rotor helicopter with a tail system. As the first step of the designing, an air-cooled, 2-stroke engine was selected and a prototype transmission was designed by determining the rotating speed of main rotor shaft. A 'pusher' type tail rotor system was adapted to balance the reaction torque and reduce the power use. The tail boom length was designed to avoid the rotating trajectory of the main rotor. The RF console consisted of the engine control, attitude control, and emergency control modules. Assembling the prototype concluded the mechanical development of the agricultural helicopter.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.123-126
• /
• 2003

This paper describes the development procedure for Tail-Fan system which has the role of anti-torque and yaw control in helicopter. A detailed design of Tail-Fan system was done and structural analysis also was done. After finishing detailed design, Detailed drawings were generated for manufacture. Through detailed design and manufacture, required techniques were achieved for helicopter development. After validation through performance and stability test, acquired techniques will be applied to development of Korea Multi-role Helicopter(KMH) which will be launched

• 항공우주기술
• /
• 제11권1호
• /
• pp.185-191
• /
• 2012

본 논문에서는 축소 로터의 성능시험과 축소 헬기 Flight Test Bed 개발이 가능한 헬리콥터 섀시다이나모미터(HCDS)를 개발하여 지상시험을 수행하였다. 축소 헬기는 엔진 출력에 따른 컬렉티브 피치각의 상호 관계로부터 로터의 일정 회전속도에 대한 추력과 동력의 변화를 확인하고, 그 결과로 OGE에서의 정지비행효율(F.M.)이 0.76으로 비행시험 가능성을 점검하였다. 본 헬리콥터 섀시다이나모미터(HCDS) 시험 결과는 축소 헬기 개발과 로터 블레이드의 성능 평가에 활용할 것이다.

• 항공우주시스템공학회지
• /
• 제2권2호
• /
• pp.14-19
• /
• 2008

This paper presents the procedure and the results of the preliminary design of the fuel tank as a part of developing the helicopter. For the requirements of operational capability, MIL-DTL-27422D and Defence Standard 15-2/Issue 1 are considered to be applied in developing a helicopter fuel tank. The procedure of the fuel tank development is set up including interface plate design, tank design, former design, tank material lay-up, and tank installation assessment. The outer moulded line and fittings of fuel tank have being designed, and several test will be performed to get the qualification.

• 대한기계학회논문집A
• /
• 제33권9호
• /
• pp.922-929
• /
• 2009

This paper deals with the State-Dependent Riccati Equation (SDRE) Technique for the design of helicopter nonlinear waypoint guidance controller. To generate the flight guidance through multiple waypoints, we use the trigonometric spline. The controller design and its validation is based upon a level 2 simulation helicopter model and the designed SDRE controller is applied to the trajectory tracking problems. To validate the designed SDRE controller, the simulation environment of high fidelity helicopter model is developed using three independent computers. This paper focuses on the validation the present SDRE controller through the helicopter waypoint guidance simulation.

• 한국군사과학기술학회지
• /
• 제10권1호
• /
• pp.22-32
• /
• 2007

This paper describes a study of a helicopter database for the sizing stage of a preliminary design process. The database includes specifications and performance parameters for more than 150 conventional single rotor helicopters currently in market. Design parameters, including configuration and weight parameters, have been analyzed and trend curve equations(regression equations) are derived using the regression analysis method. Finally, the applicability of this research result was verified whether the method is reliable for being adopted as a useful design tool in the early stage of a helicopter design process.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1992년도 한국자동제어학술회의논문집(국제학술편); KOEX, Seoul; 19-21 Oct. 1992
• /
• pp.344-348
• /
• 1992

This paper describes a procedure to design a hovering flight controller for a model helicopter using LQG theory. Parameters of the model helicopter in hover are obtained using direct measurements and calculations proposed by other research. A feedback co is by using digital LQG theory. First, a full state feedback controller is designed to the discretized system taking desirable transient response and other assumptions into account. Then a full-state estimator is designed and revised until desirable response is obtained while global stability is maintained. Performance of the controller is tested by computer simulations. Experiments have been performed using a 3-degree-of-freedom gimbal that holds the model helicopter, and the controller exhibited stable hover capability.

• 한국항공운항학회지
• /
• 제15권1호
• /
• pp.18-25
• /
• 2007

The safety should be primarily considered for air vehicle, such as helicopter, which is not easy to cope with when out of order or loss of control that followed catastrophe. The U.S National Transportation Safety Board (NTSB) investigated and analyzed for 34 years rotorcraft accidents that occurred from 1963 through 1997. This paper handles intensively the relative investigation and analysis of recent 10 years domestic civil helicopter accidents to those of the United States in order to increase the safety of helicopter transportation and to consider the main design parameter before we develop Korean Civil Helicopter. To understand the overview of civil turbine helicopter accident, it uses the NTSB's accident investigation results and the overall accident trend for U.S civil single and twin turbine engine helicopter according to category, cause, activity, and phase of operation.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2003년도 종합학술발표회 논문집 Vol.13 No.1
• /
• pp.208-212
• /
• 2003

An airborne radar is an essential aviation electronic system of the helicopter to perform various missions in all-weather environments. This paper presents the conceptual design results of the multi-mode pulsed Doppler radar system testbed model for helicopter. Due to the inherent flight nature of the hovering vehicle which is flying in low-altitude and low speed, as well as rapid maneuvering, the moving clutters from the platform should be suppressed by using a special MTD (Moving Target Detector) processing. For the multi-mode radar system model design, the flight parameters of the moving helicopter platform were assumed: altitude of 3 Km, average cruising velocity of 150knots. The multi-mode operation capability was applied such as short-range, medium-range, and long-range depending on the mission of the vehicle. The nominal detection ranges is 30 Km for the testbed experimental model, but can be expanded up to 75 Km for the long range weather mode. The detection probability of each mode is also compared in terms of the signal-to noise ratio of each mode, and the designed radar system specifications ate provided as a design results.

• Journal of Biosystems Engineering
• /
• 제34권2호
• /
• pp.89-94
• /
• 2009

Aerial application using an agricultural unmanned helicopter was suggested for an alternative against current pesticide application methods. Centrifugal clutches play important roles in the performance and safety of the helicopter operation. A previous study analyzed and verified the power transfer theory of the guide type centrifugal clutch. Based on the clutch theory, optimal designs of the clutch became possible and feasible using a simulation method. Design criteria of the clutch were the power transfer capacity of 24.66 kW(33.5 PS) at the rated engine speed and the engaging range speed of 3,000${\sim}$3,500 rpm. Various designs were accomplished using the simulation. An optimal clutch was simulated by determining the values of spring constant and mass of friction sector, which were 94,700 N/m and 123.7 g, respectively. The design performed the power capacity of 24.86 kW(33.8 PS) and engagement speed of 3,069 rpm, meeting the design criteria. Using the designed clutch, an efficient transfer of the power would be possible for the unmanned agricultural helicopter.