• Journal of Advanced Marine Engineering and Technology
• /
• 제31권5호
• /
• pp.522-530
• /
• 2007

In order to extract small hydropower in the very low specific speed range of $n_s<10$, a Positive Displacement Turbine (PDT) has been proposed and steady performances have been determined experimentally. However, the suppression of large pressure fluctuation is inevitable for practical application of PDT. Therefore, present study adopted 4-lobe helical type robe to reduce the pressure fluctuation. The results show that 4-lobe helical type robe can be adopted to suppress the pressure fluctuation drastically. Moreover, efficiency and unit power of the turbine with newly proposed 4-lobe helical type lobe are higher than those of the turbine with 3-lobe straight type robe.

• 한국소음진동공학회논문집
• /
• 제27권1호
• /
• pp.36-42
• /
• 2017

Helical gear excitation is transmitted to a gearbox through the shafts and bearings and the vibration of the gearbox radiates the noise in the air. Therefore gearbox modeling is essential to evaluate the gear noise. This work deals with vibration and acoustic analysis of a cylindrical shell-type gearbox with/without holes excited by helical gears and focuses on the development of the simple gearbox model. To do so, helical gears and bearing forces are calculated. Gearbox with/without holes is modeled by the aluminum end plates and PMMA cylindrical shell body. The vibration mode and the forced harmonic response were calculated by the commercial FE software and the end plate of the gearbox is more contributed to vibration than the body. Acoustic analysis was also conducted by the commercial acoustic software and a cylindrical shell type gearbox with/without holes has the similar vibro-acoustic characteristics.

• 한국산업융합학회 논문집
• /
• 제7권4호
• /
• pp.419-424
• /
• 2004

In order to increase the efficiency of the sawdust machine, the helical type drums with an oblique cutting condition (3D) were developed. The preexisting drums have an orthogonal cutting condition (2D) considering of a saw cutter and a wood cutting pattern. Unfortunately, the disadvantages of this type drum are the big cutting resistance, the high cost of a cutting power and the extreme occurrence of a vibration. To improve this shortcoming, the helical type drum with an oblique cutting condition was developed. Therefore, this type drum decreased the vibration and the cutting resistance of the sawdust machine, and also improved the productivity of 30% or more and the porosity of the sawdust.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.88-92
• /
• 2004

We developed a helical type drum with an oblique cutting condition for sawdust machine. The existing drum has an orthogonal cutting(2D) condition considering of saw cutter and wood cutting pattern. Additional disadvantage of this type include big cutting resistance, high cost of cutting power and extreme occurrence of vibrations. To improve this shortcoming, we developed a helical type drum with an oblique cutting(3D) condition, therefore, this type drum decreased the vibration and cutting resistance of sawdust machine, and also improved productivity and sawdust porosity.

• 한국정밀공학회지
• /
• 제15권6호
• /
• pp.40-47
• /
• 1998

Drilling is an indispensable process in manufacturing of the die and mould and the other mechanical parts which needs high dimensional and surface accuracy. In this paper, a new type of drilling method was proposed in order to improve both processing efficiency and accuracy. Specifically, the helical motion using ball end mill tools, instead of normal drilling method, was applied to perform an effective hole machining. In this paper, an theoretical background of the new type of drilling method was established, and the feasibility of the proposed theory was proved by experiments, where proposed drilling process in the paper gave a different machining specification than general method did.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권6호
• /
• pp.707-714
• /
• 2007

The heat transfer coefficient and Pressure drop during gas cooling process of $CO_2$ (R-744) in inclined helical coil copper tubes were investigated experimentally. The main components of the refrigerant loop are a receiver. a variable-speed pump. a mass flow meter, a pre-heater and a inclined helical coil type gas cooler (test section). The test section consists of a smooth copper tube of 2.45mm inner diameter. The refrigerant mass fluxes were varied from 200 to $600[kg/m^2s]$ and the inlet Pressures of gas cooler were 7.5 to 10.0 [MPa]. The heat transfer coefficients of $CO_2$ in the inclined helical coil tubes increases with the increase of mass flux and gas cooling pressure of $CO_2$. The pressure drop of $CO_2$ in the gas cooler shows a relatively good agreement with those Predicted by Ito's correlation developed for single-phase in a helical coil tube. The local heat transfer coefficient of $CO_2$ agrees well with the correlation by Pitla et al. However, at the region near pseudo-critical temperature. the experiments indicate higher values than the Pitla et al. correlation. Therefore. various experiments in the inclined helical coil tubes have to be conducted and it is necessary to develop the reliable and accurate prediction determining the heat transfer and pressure drop of $CO_2$ in the inclined helical coil tubes.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.144-149
• /
• 1996

In this paper, the clamping type forging of helical gears has been investigated. Clamping type forging is an operation in which the product is constrained to extrude sideways through an orifice in the container wall. Punch is cylindrical shaped. The punch compresses a cylindrical billet placed in a die insert. As a consequence the material flows in a direction perpendicular to that of punch movement. The forging has been analysed by using the upper-bound method. A kinematically admissible velocity field has been developed, wherein, an involute curve has been introduced to represent tooth profile of the gear. Numerical calculations have been carried out to investigate the effects of various parameters, such as module, number of teeth, helix angle, friction factor and initial height of billet on the forging of helical gears.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1969-1974
• /
• 2004

The performance of small cyclone is analysed by an experiment for the purpose of developing a bag-less vacuum cleaner. For the high collection efficiency and low pressure loss cyclone, the effect of cyclone inlet feature must be well understood. Four types of the helical inlet are considered to compare with the normal tangential inlet, and also various inlet velocities are used to each inlet type. Based on the reference dimension, each type of inlet shows the changes of the grade efficiency and pressure loss which determine the cyclone quality. The results show that the helical inlet has the smaller cut-size but bigger pressure loss than the tangential inlet. And the degree of opening area influences factors of cyclone performance. As the inlet velocity is increased, the cut-size becomes smaller and the pressure loss becomes bigger of each cyclone. Further studies are required to understand the optimized helical inlet of cyclone.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2723-2728
• /
• 2008

The present study is numerically and experimentally performed to reveal the pumping characteristics of a helical-type molecular drag pump (HTDP) in the molecular transition flow region. In the experimental study, the pressures are measured simultaneously at the 5 positions along the helical channel of rotor under various conditions of outlet pressure and throughputs, and nitrogen is used as test gas. The outlet pressure is in the range of 26-533 Pa. As results, the local pressure changes are checked corresponding to the various outlet pressure and throughput of HTDP. In the numerical study, Navier-Stokes equations with slip boundary conditions are employed (Re< 1000, Kn< 0.1). The local pressure distribution and the pumping speed are calculated. The numerical results are compared with the experimental results. The numerically computed value agrees with the experimental data within an error of approximately 5%.

• 한국분무공학회지
• /
• 제24권1호
• /
• pp.15-20
• /
• 2019

The agitator is an important industrial instrument widely used for mixing various solutions in the industrial field. In this study, the optimized design of the helical ribbon type impeller, which is mainly used for the stirring of the high viscosity solution, is carried out by CFD analysis. For this purpose, an index for evaluating the agitation performance is newly defined and an optimization design process is performed through a multiphase computational fluid dynamic analysis. From these results, it is understood that the stirring performance is maximized in the case of the helical ribbon impeller under given operating conditions when the width is 7.5 mm, the height is 160 mm and the turn is 1.